HunterDouglas RB 500 User manual

HInstallation Instructions
RB 500 Motorized Roller Shade
Motorized Coupled Roller Shade
---HunterDouglas 0


Slide the bracket cover onto the bracket until it snaps.
The fastener of the bracket adapter must be open.
Install the bracketswith the screws provided.
a)recess b)ceiling c)wall
Place the shade with the tube bearing plug
onto the bracket. (1) Push the shade against the idle
end and lift the shade up (2).
Fix the blind by turning the locking ring against the
bearing.
Slide the end caps onto the brackets. Make sure that
the end caps snap onto the brackets.
Connect the motor and controls in accordance with
separately provided instructions.
... until the motor front plate ts the bracket ring.
Turn the blind (10°) in the rolling off direction and
close both fasteners of the bracket ring. Make sure
that limit switches are accessible.
To adjust skewing, put the provided Allen key into
the screw of the leveller and turn it left or right to
move the blind up and down. Support lifting of large
heavy blinds with the palm of your hand.
Option: Leveller
Installation
Make sure that the opening for the Allen key is
pointing downwards before installing the brackets.
Change the orientation by loosening the 4 screws
(M5 x 8) and turning the leveller 90°. Fix the screws.
1
2
INSTRUCTIO
2
1
a
c
b
click
click
click
2

Slide the cover cap onto the bracket until it snaps.
The fasteners of the bracket ring must be open.
Fix the bracket with the screws provided
a recess b ceiling c wall
Press the blind with the bearing onto the bracket.
Push the blind against the idle end and lift the blind
up ...
Secure the shade by turning the locking ring
furthest away from the bracket.
Slide the bracket covers onto the brackets. Make sure
that the bracket covers snap onto the brackets.
Connect the motor and controls in accordance with
separately provided instructions.
Line up teeth of motor Plate L with the bracket adapter
(A).Turn the shade (10°) in the rolling off direction (1)
close fastener onthe bracket adapter (2). Make sure
that limit switches are accessible on motors.
To adjust skewing, put the provided Allen key into
the screw of the leveller and turn it left or right to
move the blind up and down. Support lifting of large
heavy blinds with the palm of your hand.
Option: Leveller
Installation
Make sure that the opening for the Allen key is
pointing downwards before installing the brackets.
Change the orientation by loosening the 4 screws
(M5 x 8) and turning the leveller 90°. Fix the screws.
1
2
INSTRUCTIO
2
1
a
c
b
click
click
click
3
A

     

 

4

click
click
2
1
2 1
3
Fix the outer bracket with the screws provided.
Install the main roller shade with the coupling end
cap.
Slide the cover cap onto the bracket until it snaps.
Press the idle end, lift the roller shade and snap it to
the bracket.
Fix the roller shade by turning the locking ring
against the idle end.
To align the bottom rails, push the shade against
the idle end (1), turn the shade, level the bottom rail
ZLWKWKHRWKHURQH5HOHDVHWR¿[WKHSRVLWLRQ
Not possible when using connector set.
Slide the aligner or the connector set through the
intermediate bracket into the tube bearing plug.
Place the tube with plug connector on the aligner or
connector set head.
Installation
Shades with custom width gaps or Joint 45° will
require 2 intermediate brackets. Slide the aligner or
connector set through the intermediate bracket into
the tube bearing plug.
5

click
click
2
1
2 1
3
Fix the outer bracket with the screws provided.
Install the main roller shade with the coupling end
cap.
Slide the cover cap onto the bracket until it snaps.
Press the tube bearing plug, lift the roller shade and
snap it to the bracket.
Secure shade band by turning the locking ring
on tube bearing plug furthest away from the bracket.
To align the bottom hembars, pull the shade away
from aligner set (1), turn shade to line up bottom
hembars together 5HOHDVHshade WRsecure 
position (3). Not possible when using connector set.
Slide the aligner or the connector through the brack-
et into the idle end.
Place the tube adapter on the aligner or connector
head.
Installation
Only for coupling with 2 intermediate brackets! Fix
the inner bracket (with mounted end cap) with the
screws provided. Slide the aligner or the connector
through the bracket into the idle end.
6

click
Lift the backside of the end cap and slide it in your
direction.
Type 5-217
Move the roller shade downwards out of the brack-
et. Pull the aligner or connector out of the idle end.
Unfasten the locking ring. Slide a screw driver
between locking ring and bracket and push the idle
end in the aligner direction.
To adjust skewing, put the provided Allen key into the
screw of the leveler and turn it left or right to move
the roller shade up and down. Support lifting of large
heavy roller shades with the palm of your hand.
Installation Instruction
Roller Shade
Coupled Shades
Option: Leveler
Make sure that the opening for the Allen key is
pointing downwards before installing the brackets.
Change the orientation by loosening the 4 screws
and turning the leveler 90°. Reinstall the screws.
Removal
Slide the bracket cover onto the bracket. Make sure
that the bracket cover snapsonto the bracket.
7

Slide the cover cap onto the bracket until it snaps.
The fasteners of the bracket ring must be open.
Fix the bracket with the screws provided
a recess b ceiling c wall
Press the blind with the bearing onto the bracket.
Push the blind against the idle end and lift the blind
up ...
Fix the blind by turning the locking ring against the
bearing.
Slide the end caps onto the brackets. Make sure that
the end caps snap onto the brackets.
... until the motor front plate ts the bracket ring.
Turn the blind (10°) in the rolling off direction and
close both fasteners of the bracket ring. Make sure
that limit switches are accessible.
Connect the motor and all controls in accordance
with all safety standards.
Installation
1
2
2
1
a
c
b
click
click
click
8

click
Lift the backside of the bracket cover and slide it
towards you.
Type 5-217
Move the roller shade downwards out of the bracket.
Pull the aligner or connector out of the tube bearing plug.
Unfasten the locking ring. Slide a screw driver
between locking ring and bracket and push the tube
bearing plug in the aligner/connector direction.
To adjust skewing, put the provided Allen key into the
screw of the leveller and turn it left or right to move
the roller shade up and down. Support lifting of large
heavy roller shades with the palm of your hand.
Installation Instruction
Roller Shade
Coupled Shades
Option: Leveler
Make sure that the opening for the Allen key is
pointing downwards before installing the brackets.
Change the orientation by loosening the 4 screws
(M5 x 8) and turning the leveller 90°. Fix the screws.
Removal
Slide the end cap onto the bracket. Make sure that
the end cap snap onto the bracket.
9

Open both fasteners of the bracket ring. Turn the
blind in the roll up direction until the front plate gets
out of the bracket ring.
Type 5-216
Push the blind against the bearing and slide it out
of the bracket.
... and slide it towards you.
Installation Instruction
Roller Blind
Motor Operation
Unfasten the locking ring.
Disconnect power to the motor. Lift the backside
of the bracket cover...
2
1
1
2
10