HunterDouglas RB 500 User manual

SURFACE/WALL MOUNT
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
020519
END PLATES
INSTALLING A POCKET
BOTTOM CLOSURES
TOOLS NEEDED
Pencil Level
Measuring
Tape Drill with
bits
Screwdriver
Pocket Installation - 5.25" Single and 9" Single and Dual Shades
Manual
Single
Shade
Dual Shade
9” Pocket Only
Motorized
Single
Shade
Manual
Bracket
55L or 75L
Motor
Bracket
55L or 75L
Surface Mounted
Use bracket and shade instructions for
Standard+ & Heavy Duty+ Manual
Surface Mounted
Use bracket and shade instructions for
RB 500 Heavy Duty Bracket Motorized
Surface Mounted
Use bracket and shade instructions for
Heavy Duty+ 7" Dual Bracket Motorized or Manual
Mount into wood or metal studs
or into concrete with concrete
anchors. Drywall anchors are not
recommended.
Determine the mounting location.
Pre-drill the pocket. Mount in
place.
Use a screwdriver to attach
the end plates with the
screws provided.
Tilt the bottom closure inside the
front edge of the pocket until the
closure catches on the inside ledge.
7" Dual
Motor
Bracket
Side View
1 of 4

© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
2 of 4
OPTIONAL: INTEGRATED LEVELER
ADJUST LEVELERIDLE END
TOOLS NEEDED
INSTALLING THE BRACKETS
Pencil Level
Measuring
Tape Drill with
bits
Allen Key
(provided with
optional Leveler)
Screwdriver Pliers
040419
MOTORS
Sonesse 50 RTS 506S2 & 510S2 120V AC
Plug-In
Quick Disconnect
Motor Front Plate
(comes attached to motor)
Insert the provided Allen key into the set screw of the leveler.
Adjust skewing by turning the Allen key left or right to move
the shade up or down. Support the shade with your hand if
necessary.
All adjustments can be made after the shade has been
installed and after the operation has been tested.
Sonesse 50 RTS 506S2 & 510S2 Motor with
Coupled 7" Dual Brackets in 9" Pocket
Motorized Shade Installation Series 5-267–216
Compatible Motors
LT50 RA 525A2
LT50 Altus RTS 525A2
Sonesse 50 RTS 506S2
Sonesse 50 DCT 506S2
Sonesse 50 RA 506S2
Sonesse 50 RS485 506S2
Sonesse 50 RTS 510S2
Sonesse 50 DCT 510S2
Sonesse 50 RA 510S2
Sonesse 50 RS485 510S2
Sonesse ULTRA 50 RTS 506A2
Sonesse ULTRA 50 RA 506A2
Sonesse ULTRA 50 RS485 506A2
LT50 RS485 515S2
LT50 RS485 535A2
Sonesse ULTRA 50 DC RTS 504A8
Sonesse 50 DC RS485 504A8
Sonesse 30 RTS
Sonesse 30 DCT
Sonesse 30 RS485
7" DUAL BRACKETS IN A 9" POCKET
Determine the mounting location inside the pocket.
Measure and mark the bracket locations with a pencil.
Mount brackets with the screws provided. Pre-drilling is
recommended.
Check that the brackets are level and aligned.

3
click
1
2
3 of 4
INSTALLING THE SHADE - Do not remove the tape around the shade until it is fully installed
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
MOTOR BRACKET
2
1
Push the shade against the
idle end and lift the roller
shade up until the motor
front plate fits into the
motor bracket.
Turn the roller shade approximately
10˚ in the rolling direction and close
both fasteners of the brackets.
Repeat to install the front shade.
MOUNT OUTER BRACKET AND COUPLER
MOUNT THE COUPLED SHADE
COUPLING 2 INTERMEDIATE BRACKETS
ALIGNER SET ADJUSTMENT
Fix the outer
bracket in to
the pocket
with the
screws
provided.
Place the
tube with
plug
connector
on the
aligner or
connector
set head.
Press the tube
bearing plug,
lift the roller
shade and
snap into the
idle bracket
end.
Slide the
aligner or the
connector
through the
bracket into
the idle end.
Fix the inner
bracket with the
screws provided.
Slide the aligner or
the connector
through the
bracket into the
idle end.
2
1
2 1
3
To align the bottom
hembars, pull the shade
away from the aligner set
(1), turn the shade to line
up the bottom hembars
together (2). Release the
shade to secure the
position (3). Not possible
when using a connector
set.
click
Sonesse 50 RTS 506S2 & 510S2 Motor with
Coupled 7" Dual Brackets in 9" Pocket
Motorized Shade Installation Series 5-267–216

REMOVE COUPLED SHADE FIRST
4 of 4
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
SHADE REMOVAL
UNLOCK THE SHADES
DISCONNECT THE MOTOR
Rotate the
nut on the
idle end
countercloc
kwise to
unlock the
shade.
RELEASE THE SHADE
1
2
Disconnect the power cable
from the electrical source.
Plug-in: Unplug from the
outlet
Quick Disconnect: Unplug the
quick disconnect cables
Wired to the junction box:
Electrician is required
Open the bracket fasteners.
Turn the shade in the roll up
direction until the motor front
plate releases.
Push the shade in the direction
of the idle bracket to slide it out
of the bracket and down to
remove it completely.
Place a screwdriver between the
bracket and bearing plug and push
towards the aligner to remove the
shade. Move the shade downward
and out of the bracket. Remove the
aligner or connector from the bearing
plug.
LOCK THE SHADE CHECK SHADE
OPERATION
UNLOCKED LOCKED
Rotate the nut on the
idle end clockwise
until it meets the tube.
This locks the shade
into position.
Remove the tape from the shade.
Make sure the shade operates properly. Use separate
wiring information per motor type and programing
instructions from HDhospitality.com
Adjust leveler if applicable.
Sonesse 50 RTS 506S2 & 510S2 Motor with
Coupled 7" Dual Brackets in 9" Pocket
Motorized Shade Installation Series 5-267–216