KI Engage Task Chair Installation instructions

Required
Tools
Disassembly Instructions
Material Type:
Warning: This drawing format requires special non-standard fonts!!
Make sure the appropriate font files are installed!!!
TT Humanst 521 BT Light
O HelveticaLTStd-Cond
O HelveticaLTStd-LightCond
Engage Task Chair, Engage Stool, Piretti 2000 Task Chair, Piretti 2000 Stool
Page 1 of 3Rev. 1P0033-0080
A. Steel B. Plastic C. Foam D. Fabric
KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com
Procedure:
1. Pry off the rear shrouds from the backrest.
2. Pry the Back Shroud from the Back Assembly.
3. Remove the screws holding the backrest to the steel backrest
support and remove the backrest.
(continued next page)
General Notes:
1. Disassembly time: 30-45 minutes
2. This procedure assumes basic familiarity with hand tools and
furniture terminology: no specialized training is required
3. All materials removed and disassembled shall be sorted and
segregated with like materials and disposed of or recycled
according to recycling availability or waste acceptance
4. For items to be recycled, refer to KI's End of Life Recycling
Matrix and KI's End of Life Recovery Options Matrix, available
at www.ki.com
All fasteners not explicitly tagged
are Material Type A: Steel
Procedure:
1. Remove the screws holding the backrest onto the back sup-
ports and remove the backrest.
2. Pry off the cover under the seat to expose the seat support
plate. Remove the screws holding the support plate to the seat
and remove the seat.
3. Remove the screws holding each arm cap to the back sup-
ports and remove the arm caps.
4. Pry out the end caps holding the arms onto the torsion tube
and remove the outer bushings. Rotate each inner bushing so
that the slot underneath is aligned with the pin. Push back on
the support which will allow the pin to drop out. Pull the sup-
ports and inner bushings away from the frame and pull out the
leaf springs.
5. Pry out the caps from the seat frame tubes underneath the seat.
6. Pry out the casters and caster bushings from the chair base.
See Sheet 3
See Sheet 2
Gloves Safety Glasses Pry Bar
Philips Screwdriver Putty Knife
Hex Socket Wrench
Rubber Mallet Flat Screwdriver
Channel Lock Pliers Torx Screwdriver
Robertson Screwdriver
Robertson Screwdriver
Allen Wrench
B
B
D
C
B
A
B

Required
Tools
Disassembly Instructions
Material Type:
Warning: This drawing format requires special non-standard fonts!!
Make sure the appropriate font files are installed!!!
TT Humanst 521 BT Light
O HelveticaLTStd-Cond
O HelveticaLTStd-LightCond
Engage Task Chair, Engage Stool, Piretti 2000 Task Chair, Piretti 2000 Stool
Page 2 of 3Rev. 1©2013 Krueger International, Inc. All Rights Reserved · P0033-0080
A. Steel B. Plastic C. Foam D. Fabric
KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com
All fasteners not explicitly tagged
are Material Type A: Steel
Procedure:
1. Pry off the rear shroud from the backrest.
2. Remove the screws holding the backrest to the steel backrest
support and remove the backrest.
3. Remove the screws holding any amrests and the seat to the
seat support mechanism and remove the armrests and seat.
Remove the armrest pads and housing from the support.
4. Invert the chair and gently tap on the bottom of the steel height
adjustment cylinder while lifting the plastic base. Remove the
plastic chair base and height adjustment cylinder shroud from
the steel cylinder.
WARNING: CONTENTS UNDER PRESSURE!
REMOVE WITH CAUTION.
5. Pry off the plastic control knob, handles and backrest support
shroud halves from the support mechanism.
6. Discard the backrest, seat, chair base and plastic components.
7. Recycle the seat support mechanism, seat slides, back support
(J-bar), armrest supports and height adjustment cylinder.
4. Remove the screws holding any armrests and the seat to the
seat support mechanism and remove the armrests and seat.
5. Pry off the plastic control knob, handles and shrouds from
the support mechanism.
(continued next page)
B
B
BC
BCD
A
C
B
B
C
B
B
Gloves Safety Glasses Channel Lock Pliers Philips Screwdriver Torx Screwdriver Pry Bar Hex Socket Wrench
Rubber Mallet

Required
Tools
Disassembly Instructions
Material Type:
Warning: This drawing format requires special non-standard fonts!!
Make sure the appropriate font files are installed!!!
TT Humanst 521 BT Light
O HelveticaLTStd-Cond
O HelveticaLTStd-LightCond
Engage Task Chair, Engage Stool, Piretti 2000 Task Chair, Piretti 2000 Stool
Page 3 of 3Rev. 1©2013 Krueger International, Inc. All Rights Reserved · P0033-0080
A. Steel B. Plastic C. Foam D. Fabric
KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com
All fasteners not explicitly tagged
are Material Type A: Steel
6. Invert the chair and gently tap on the bottom of the steel height
adjustment cylinder while lifting the plastic base. Remove the
plastic chair base and height adjustment cylinder shroud from
the steel cylinder.
WARNING: CONTENTS UNDER PRESSURE!
REMOVE WITH CAUTION.
7. Discard the backrest, seat, chair base and plastic components.
8. Recycle the seat support mechanism, back support (J-bar) and
height adjustment cylinder.
Safety Glasses
Gloves Channel Lock Pliers Pry Bar Rubber Mallet
A
A
B