Kongskilde 300FL User manual

ASSEMBLY INSTRUCTIONSRTS
& OPERATING GUIDE
For 300FL Finger Tine Harrow Kit for 300SS Rota Harrows
Kongskilde 300 FL Kit
300FL Harrows
Finger Tine Harrow Kit

2
INDEX
INTRODUCTION: ................................................................................................................ 3
PRE ASSEMBLY TIPS: ....................................................................................................... 3
Mounting Brackets:............................................................................................................ 4
FL Tine Mounting:...............................................................................................................5
FIELD SETTINGS:............................................................................................................... 6
ADJUSTMENTS / PRECAUTIONS: ................................................................................... 8
MAINTENANCE: ................................................................................................................. 9

3
INTRODUCTION:
The Kongskilde 300 FL - Finger Tine Harrow Attachment has been developed as a optional
pre-levelling attachment for Kongskilde 300 Series Double Rota-Harrows.
When properly adjusted, the 300 FL Harrow Attachment will help to divide the flow of soil from
thebackrowoftines,thusreducingtheridgesthatforminfrontofthedoublerotaharrows.This
pre-levelling of the soil surface enhances the performance of the double rota-harrows in
preparing a level surface for planting in various field conditions and soil types.
This booklet has been developed to assist you in assembling your 300 FL Harrow Kit for
Kongskilde cultivator equipped with 300 Series Double Rota-Harrows.
PRE ASSEMBLY TIPS:
Priortoassemblingthe300 FLFingerTine Harrows, the cultivator should be carefully unfolded
and lowered to the ground, (resting on the tines), on a flat level area.
The 300 Series - Double Rota-Harrows must be mounted first, according to the instructions
provided in the HarrowAssembly & Operator Manual no. 03 150 109.
We strongly recommend that you do not attempt to assemble the harrows before mounting to
the cultivator, as the harrow sections are heavy and difficult to move when assembled. It is
also difficult to insure correct placement and spacing of the harrow sections if they have been
pre-assembled.
NOTE: Before starting be sure to check that you have all of the correct components in order to
assemble each section of harrows as shown in the parts list booklet and assembly diagrams
provided.

4
Mounting Brackets:
1. With the Double Rota-Harrows fully assembled and the cultivator laid out on a flat level
area, begin by selecting the locations for the mounting brackets on the front roller frame tube.
2. The location of the mounting brackets will vary from roller to roller depending on the
position of the roller harrow hanger arms and tine locations. Place the mounting brackets at
the best possible location on the roller frame tubes so that they will not interfere with the
placement of the FL finger tines in step 4.

5
3. After securing the mounting brackets, match the toolbar length to the roller section and
attach the toolbars to the mounting brackets with the wire tine clamps provided. The toolbars
can be shifted a few inches to the right or left of centre as required for correct mounting of the
FL finger tines.
FL Tine Mounting:
4. The Finger Tines must be mounted so that they are being pushed in the direction of
travel as shown below.
5. Position one finger tine about 4" to the right and left of each tine on the back row of the
cultivator. Secure the FL tines to the toolbars with the tine clamps, nuts, bolts and washers
provided.Whencompleted,therewill be 2 FLtinesmountedon the toolbars for every S-tine on
therearbarofthe cultivator.Forfurtherinstructionsonlocating the FLtinesrefer to the section
on field settings.

6
FIELD SETTINGS:
A) NOTE: There are many factors that can affect the ability of the harrows to level the soil
surfacebehindthe cultivator; Cultivator tinespacing,typeofshares(sweeps), cultivating depth,
ground speed, direction of travel across the field (angle), soil type, and soil conditions like
moisture content and crop residue levels, all have an affect on the quality and levelness of the
seed bed. Therefore, do not expect the same settings to work in every case. Be prepared to
adapt and adjust your equipment and operating practices to obtain the best results for each
field condition.
B) The down pressure on the rota-harrows can be increased or decreased by turning the
spring adjustment bolt with a 15/16" socket wrench. First loosen the jamnut then adjust the
downpressureontherollers as required to break lumps or clods and obtain a levelsoilsurface.
Securethejamnut.(Forfurther instructions on the double rota-harrows refer totheappropriate
section in the 300 SS harrow manual.)
C) For best results, move the FL finger tines from 4" to 8 " to the right or left behind the tines
as required, so that the finger tine divides the flow of soil coming from the rear row of cultivator
S-tines in half, or knocks down the ridge formed in between the tines into 2 smaller ridges. By
pre-levelling the soil in this way the rota harrow has better contact with the entire soil surface
creating a more uniform surface and soil structure for planting.

7
D) The angle of the FL tines can be adjusted to 4 different positions.The steeper the angle
-the more aggressivethetineactionbecomes. Selection oftheworkinganglewill again depend
onthesoil type and the amountof crop residue left onthe soil from the previousyears harvest.
Field testing has shown that in most cases the best working angle for the FL tines is when the
stop block is located in position 4.
E) Theheightofthe FLtineson eachtoolbarcanbeadjustedto3 differentpositions.Normally
the bracket should be set at the highest position (1) and then lowered to position (2) or (3) as
the finger tines wear. When the tines becomes worn down after position (3) they should be
replaced.

8
ADJUSTMENTS / PRECAUTIONS:
Whenthe assembly of the harrows has beencompleted check to make sure that thecomplete
assembly appears evenly spaced and centred across the back of the cultivator. If the harrow
assemblyisnotcentredyoumayhavetoshifttheharrowsectionsasrequired.Impropercentring
of the harrows may cause the cultivator to pull crooked in the field.
Check to make sure that each section of harrows can move up and down freely. It is important
that the harrow sections will not hit each other when working on uneven ground.
Check all nuts and bolts and secure if loose.
Takecarewhenfolding thecultivatorfortransport forthefirst timeaftercompletingtheassembly.
Check to make sure that the harrows do not interfere with each other or other cultivator frame
components when folding and unfolding.
DANGER! NEVER STAND OR WORK IN THE AREA BELOW THE WINGS OR
UNDER AN UNSUPPORTED CULTIVATOR FRAME.
ALWAYS USE WING LOCK PINS, AND WHEEL CYLINDER TRANSPORT LOCKS.
USE EXTREME CAUTION WHEN WORKING AROUND HEAVY EQUIPMENT.
BLOCK THE WHEELSAND MAKE SURE THAT THE UNIT IS SUPPORTED TO PREVENT
IT FROM FALLING BEFORE ATTEMPTING TO MAKE ADJUSTMENTS OR WHEN
PERFORMING MAINTENANCE OPERATIONS.

9
MAINTENANCE:
A) Periodically check all nuts and bolts and secure if loose.
B) Lubricate the G-bearings after every 12 hours of operation. DO NOT OVER GREASE
THE G-BEARING: Over greasing may cause damage to the bearing seals.
C) Periodically check and remove any foreign material that may become wound around the
FL tines, rollers or bearings and remove any objects (ie: stones) that have become trapped in
the rollers. Any bent or damaged roller sections should be repaired or replaced.
D) Replace or repair any bent, broken or very worn down FL tines.
Alwayschecktheconditionofyourfieldcultivatorand levelling attachments at regular intervals
and keep in good repair. Optimal performance cannot be expected of equipment in poor
condition.

603 150 561 NOVEMBER2000