Optimum 600 User manual

600
QUALITY YOU CAN TRUST
USER’S MANUAL
WHOLE COLD-PRESS SLOW JUICER

1
SAFETY FIRST 1
PARTS 4
HOW TO ASSEMBLE 6
HOW TO OPERATE 8
TIPS ON OPERATION 10
TIPS ON INGREDIENTS 11
INGREDIENTS PREPARATION 12
HOW TO DISASSEMBLE AND CLEAN 16
OPTIONAL HOW TO USE THE FROZEN FRUIT STRAINER 17
FROZEN INGREDIENTS 18
TROUBLESHOOTING Q&A 19
SPECIFICATIONS 21
WARRANTY TERMS AND CONDITIONS 22
CONTACT US 23
CONTENTS SAFETY FIRST
When using electrical appliances, basic safety precautions should always be followed, including
the following:
1. Read all instructions.
2. To protect against risk of electrical shock do not put motor or base of unit in water or otherliquid.
3. Close supervision is necessary when any appliance is used by or near children.
4. Unplug from outlet when not in use, before putting on or taking o parts, and beforecleaning.
5. Avoid contacting moving parts when power switch is on.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions,
or is dropped or damaged in any manner. Return appliance to the nearest authorised service
facility for examination for repair or electrical or mechanical adjustment.
7. The use of attachments not recommended or sold by the manufacturer may cause fire, electric
shock or injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter.
10. Always make sure juicer cover is securely in place before motor is turned on. Do not unfasten
clamps while juicer is in operation.
11. Be sure to turn switch to OFF position after each use of your juicer. Make sure the motor stops
completely before disassembling.
12. Do not put your fingers or other objects into the juicer opening while it is in operation. If food
becomes lodged in opening, use food pusher or another piece of fruit or vegetable to push it
down. When this method is not possible turn the motor o and disassemble juicer to remove the
remaining food.
13. Do not use the appliance if the filter is damaged.
14. When a separate pulp container is provided, do not operate without the pulp container inplace.
15. Please do not alter the appliance in anyway.
16. Do not use the appliance for anything other than its intended purpose as described in
themanual.
17. The appliance should be used for limited period of time (30-45 minutes).
18. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
BEFORE USING YOUR OPTIMUM 600 COLD-PRESS JUICER,
PLEASE READ THESE SAFETY INSTRUCTIONS CAREFULLY.

2 3
Unplug the power
cord when not in use.
Do not put fingers or
other objects in to the
feeding tube while it
is in operation;
*It may cause injury.
Do not keep or
operate the appliance
near infants or
toddlers;
*It may injure them.
Do not put the juicer
parts in the dish
washer or extremely
hot water;
*The parts may
wearfaster.
Do not use the
appliance on an
uneven surface;
*It may cause a
malfunction if the
appliance tips over.
Do not use any
hazardous chemicals
to clean the
appliance;
*It may change the
color of the appliance
or result in a fire.
Do not repair,
disassemble the base,
or customize the
appliance;
*The appliance may
not operate properly
causing fire, electric
shock, or injury.
Do not spray water
or flammable sprays
near the appliance;
*It may cause
an explosion or
electricalshock.
19. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
20. Children should be supervised to ensure that they do not play with the appliance.
21. Switch o the appliance and disconnect from supply before changing accessories or
approaching parts that move in use.
22. This appliance is intended to be used in domestic and commercial environments and similar
applications such as:
– sta kitchen areas in shops, oces and other working environments;
– farm houses;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments.
– the appliance will not be covered under the manufacturer warranty if the product is
abnormallyused.
23. Save the instruction manual for future reference.
24. If the appliance is given as a gift, please include the manual with the product.
FAILURE TO FOLLOW SAFETY INSTRUCTIONS AND WARNINGS COULD
RESULT IN SERIOUS INJURY. MISUSE OF YOUR JUICER MAY DAMAGE
YOUR APPLIANCE AND VOID YOUR WARRANTY.
SAFETY FIRST (CONTINUED)
The following precautions are provided to ensure the safety of the user. Please read carefully and
exercise care when using the appliance.
SAFETY FIRST (CONTINUED)

4 5
STEP 1
Top-set Assembly
Align the red dots on
each part and assemble in
the order shown.
STEP 2
Top-set and Base Assembly
Place the bowl on the base so that
its grey arrow lines up with the black
arrow on the base.
Detachable
1. Feeding Tube
2. Drum Lid
3. Juicing Bowl
4. Pulp Cup 7. Juice Cup
6. Base
5. Silicon tap
8. Silicon wiper
11. Pusher 12. Cleaning Brush
9. Filter 10. Juicing Screw
PARTS PARTS CONTINUED
*The products illustrated/photographed in this booklet may vary slightly from the actual product
Pusher
Align the dots
Align

6 7
STEP 1 Top-set Assembly STEP 2 Top-set and Base Assembly
Check Before
Operating
• Wash the parts before first use.
• Ensure that the compression silicone and silicone ring are
assembledproperly.
1Insert the compression silicone 40%
into the slot below the pulp spout.
Donot push all the way in.
and hold the bowl with your other hand
for a better grip.
Note • The Juicer may leak if not
assembledproperly.
Note • The juicing screw needs to be
pushed down firmly and locked into
place for the drum lid to close.
Note • Juicer will not operate if parts are not
assembled properly.
HOW TO ASSEMBLE HOW TO ASSEMBLE CONTINUED
Open
Close
Closed position
Open position
1A Place the bowl on the base so that its
grey arrow lines up with the black arrow
on the base.
2Assemble the filter into the silicon wiper
then place this assembly in to the juicing
bowl ensuring the red dot on the
strainer is aligned with the red dot on
the juicing bowl.
3Place the juicing screw into the filter.
Turn and press down on it until it clicks
into place.
4Place the drum lid on the juicing bowl
aligning the red dot on the drum lid with
the red dot on the juicing bowl. Turn
clockwise to close, aligning the red dot
on the drum lid with the close-mark.
TIP For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration...
5Open/Close mark on the top-set.
6Place the pulp cup under the pulp spout
and place the juice cup under the juice
spout for juice collection.

8 9
HOW TO OPERATE HOW TO OPERATE CONTINUED
STEP 1 After preparing the ingredients, plug the power cord into a wall outlet.
STEP 3 Insert the prepared ingredients one piece at a time.
STEP 4 Use the smart cap to make mixed juices, stop juice from dripping, or rinse between
dierent juices.
STEP 5 After juice and pulp are completely extracted, switch the unit OFF.
STEP 2 Press the FORWARD button to operate.
Note • Do not touch the power cord with wet hands. It may cause electrical shock,
short‑circuit, or fire.
• Check the safety of the wall outlet.
Note • Fibrous leafy vegetables (celery, kale, etc.):
» Separate each stem. Cut the outer stems that are thick and fibrous.
Bundle up the leafy vegetables and insert into the juicer. Alternate between leafy
parts and stems.
• Before extracting, remove hard seeds or pips in ingredients.
• When juicing frozen fruits with small seeds, ensure that even the seeds are
completely thawed.
• Insert the ingredients one piece at a time.
Tip • After inserting ingredients, use the pusher when it is necessary. Do not push toohard.
» Intermittently use the pusher for soft ingredients like tomatoes and apples.
Constant use of pusher for soft ingredients may aect the juice quality.
Tip • Juicing with the smart cap closed creates various mixed juice creations when
dierent fruits and vegetables are selected; milk, banana, beans, etc, are selected.
• After juicing, close the smart cap to stop the juice from dripping, especially when
disassembling the juicing bowl o the base.
• When making dierent juices quickly rinse away any leftover flavours by running a
glass of water in the juicer with the smart cap closed.
Note • Leave the smart cap open when juicing ingredients that create excessive foam
during extraction (e.g. apples, celery).
• Pay close attention when operating with the smart cap closed. Juice may overflow if
the juice collected in the juicing bowl exceeds its capacity marked on the bowl.
Note • If the remaining ingredients in the juicing bowl have not been extracted completely,
the drum lid may not open easily. After each extraction, run the juicer for an
additional 30 seconds to let the juicer extract the remaining pulp.
• When the drum lid is stuck, press the REVERSE-OFF-FORWARD button in this order;
switching back and forth 2 or 3 times to dislodge the ingredients. Then place hands
on top of the drum lid and firmly press down while simultaneously turning the drum lid
counter clockwise to open.
» Depending on the ingredients, pour water down the feeding tube to rinse out the
interior of the juicing bowl and then attempt to remove the drum lid.
Note • Forward: Pulls down and slowly masticates the ingredients.
• Reverse: Pushes the ingredients back up to dislodge them.
IF THE JUICER STOPS DURING OPERATION:
Note • REVERSE: Pushes the ingredients back up to dislodge them.
The REVERSE button only works while holding down the switch.
• Switch OFF ensuring that the juicer comes to a complete stop. Then pressREVERSE.
Hold the REVERSE button for 2‑3 seconds and release. Repeat as needed. Let the
juicer stop completely before using the REVERSE button to prevent malfunction.
• If the juicer does not work after these steps, disassemble and clean the parts
before operating the juicer again.
1 2 3 4
REVERSEOFF OFF FORWARD
TIP We recommend following a recipe to begin with.

10 11
TIPS ON INGREDIENTSTIPS ON OPERATION
1. Operating the juicer without ingredients can cause damage to the screw.
2. Do not continuously operate the juicer for more than 30-45 minutes.
This can damage the motor from overheating.
After continuous use, let the juicer rest for 30 minutes to cool down before starting
anothersession.
3. Do not put fingers or other objects into the feeding tube. Always use provided pusher
whenneeded.
If other objects are inserted into the feeding tube during operation, such materials can get stuck
and damage the juicer parts and/or cause injury.
4. Do not put dried or hard ingredients like whole grains, fruits with hard seeds or ice into the juicer.
These may damage the juicer parts (e.g. juicing bowl, juicing screw, and filter).
• Beans or grains can be used if soaked overnight or boiled.
• Fruits with pips and hard seeds (e.g. nectarines, peaches, mangoes and cherries) must be
pitted before juicing.
• When using frozen fruits with small seeds such as grapes, completely thaw before inserting
them into the juicer.
5. Do not use ingredients containing excessive amounts of vegetable oil or animal fat.
Do not use the juicer to extract vegetable oil from ingredients.
If vegetable/animal oil gets on the juicing screw, it may reduce performance and even
damage the part.
6. After juicing ingredients with seeds like grapes, thoroughly clean all the crevices on the bottom
of the juicing screw.
Juicer damage due to owner negligence or from not following the instructions in the owner’s manual
will void the warranty service.
DO NOT put the following ingredients into the juicer:
Experience the best quality juice by understanding each ingredient’s characteristics and knowing the
optimal way of handling the ingredients.
Peach, nectarines, apricot, plum, mango, etc.
Remove hard seeds from the ingredients
before juicing.
Hard seeds
Pineapple, watermelon, cantaloupe, etc.
You may like to peel the skins from the
ingredients before juicing.
Hard or
inedible
skins
Sesame seed, butter, margarine, etc.
Do not extract ingredients containing
vegetable or animal oil. This can reduce
performance and even damage the juicer.
Vegetable/
animal oil
Coconut, sugar-cane, whole grains, etc.
Do not extract ingredients with no
watercontent.
Others
The Slow Juicer is an innovative product that uses a patented slow-speed
masticating technology to eciently extract the juice fromingredients.
Thejuicer is designed to obtain the best result from ingredients with firm
composition and with high water content.
For best result, we recommend that you follow a recipe to begin with.

12 13
INGREDIENTS PREPARATION
SOFT FRUITS AND VEGETABLES (e.g. oranges, tomatoes):
If the ingredients are larger than the feeding
tube, cut the Ingredients into pieces that will fit
into the feeding tube.
EXTRACTION TIPS:
• Slowly insert the ingredients one at a time.
• Use the pusher to push the ingredients down the feeding tube. (The pusher also helps prevent juice
from spraying out of the feeding tube when extracting ingredients with high water content)
• Leave the smart cap open when juicing ingredients that create excessive foam during extraction.
(Foam can accumulate if operated with smart cap closed.)
• It is recommended that the extracted juice be consumed within 48 hours after extracting.
Depending on the density of the ingredients the extracted juice can gradually show layers
overtime.
• If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.
INGREDIENTS PREPARATION CONTINUED
HARD FRUITS AND VEGETABLES (e.g. carrots, potato, beetroot & spinach):
Soak in cold
water prior
tojuicing.
To increase the juice yield,
juice fruits and vegetables with
high water content.
PREPARATION TIPS:
Optional • Soak hard ingredient like carrots and ginger in cold water prior to juicing.
EXTRACTION TIPS:
• Slowly insert the ingredients one at a time.
• Pace the juicing speed ensuring each ingredient is thoroughly extracted.
• To maximize the juice yield, juice with ingredients with high water content.
How to Use
the Smart Cap:
Juice Yield:
Adjusting the
amount of pulp
in the juice:
• Juicing with the smart cap closed allows mixed juice creations with
dierent fruits, vegetables and liquids.
• After juicing, close the smart cap to block excess juice from dripping,
especially when disassembling the juicing bowl o the base.
• When making juices quickly rinse away any leftover flavours by running a
glass of water in the juicer with smart cap closed.
• Leave the smart cap open when juicing ingredients that create
excessive foam during extraction (e.g. apples, celery).
• Pay close attention when operating the juicer with smart cap closed. Juice
may overflow if the juice collected in the juicing bowl exceeds its capacity
marked on the juicing bowl.
• For the optimal extraction and maximum juice yield, you may like to cut
the ingredients following the guidelines given in this section.
• Insert ingredients slowly monitoring the flow of waste pulp.
The juice yield may vary depending on the speed ingredients are fed into
the juicer.
• Depending on the ingredient, you may get extra pulp in the juice when
juicing continuously.
• To reduce the amount of pulp, disassemble the top-set and wash frequently.

14 15
INGREDIENTS WITH SMALL SEEDS (e.g. raspberry, pomegranate, grape):
Insert ingredients slowly
to minimize the amount of
leftover seeds in the filter.
For best result, juice with
ingredients with higher
amount of fluid (e.g.
apple, pear).
PREPARATION TIPS:
• Thoroughly rinse ingredients like grapes. Take the grapes o and discard the stem.
• For pomegranate, discard the skin and juice only the inner part.
EXTRACTION TIPS:
• Depending on the size of the grape, insert 3–5 grapes at a time while monitoring the
extractionresult.
Caution If the lid does not open due to excessive amount of small seeds left in the juicing
bowl, continuously run the juicer for 30 seconds to extract any leftover seeds.
If the lid is still stuck, repeat REVERSE‑OFF‑FORWARD until the ingredients
become dislodged. Then twist the lid to open while pushing downwards on the
lid with palms (depending on the ingredient, pour some water down the feeding
tube for quick rinsing and to help dislodging).
INGREDIENTS PREPARATION CONTINUEDINGREDIENTS PREPARATION CONTINUED
FIBROUS AND/OR TOUGH LEAFY INGREDIENTS (e.g. celery, kale, pineapple):
When juicing leafy
ingredients like
celery and kale, do
not collect more than
500g per session.
For best result,
disassemble and
wash the top-set
before juicing again.
It’s best to juice with
ingredients with higher
amount of fluid, like
Carrots, apples: fibrous
ingredients = 9:1
[recommended ratio]
If leafy ingredients
wrap around the
juicing screw, open
the lid and remove
the fibers before
continue juicing.
PREPARATION TIPS:
Optional • Soak fibrous ingredients in cold water for about 30 minutes.
EXTRACTION TIPS:
• One at a time, slowly insert the prepared ingredients.
• Insert more ingredients after the previously inserted ingredients have been completely extracted.
1Roll leaves into spiral as inserting into the juicer.
2Insert the leafy part of the ingredients first then alternate between leafy parts and stems.
3For ingredients like wheat-grass, grab a handful and insert in a bundle.
4Ensure waste pulp continues to appear.
Caution • The fibres from tough ingredients like celery can wrap around the juicing
screw and aect juicer’s performance. Cut the stems that are thick and tough
to 4 inches long or less.
• Foam can build up from juicing fibrous ingredients. Use strainer to remove
the foam before serving.
• For ingredients like pineapple, slice o the rind of the pineapple and cut around
the fibrous core. Cut the flesh of the pineapple to smaller pieces.
• Recommended amount of juicing per session is 500g. When juicing more
than 500g, wash the top-set before continue juicing.
Slowly insert ingredients with small seeds to prevent the seeds from clogging the strainer. When the pulp outlet is blocked by the fibrous ingredients, press the REVERSE‑OFF‑FORWARD
button in this order, switching back and forth 2‑3 times.

16 17
1To assemble, place the Juicing screw and the
Frozen Fruit Strainer in the juicing bowl and close
the lid.
1Insert the Frozen Fruit Strainer into the juicing
bowl while aligning the red dots of the Frozen
Fruit Strainer with the juicing bowl.
2Insert the juicing screw into the Frozen Fruit
Strainer with a twisting motion.
3Place the lid onto the juicing bowl by aligning
the red dots of the lid and the juicing bowl.
Then, rotate the lid clockwise until the lid
issecured.
• When using the Frozen Fruit Strainer, always
leave the Smart Cap and silicon tap open.
Note • Immediately clean the juicer after
each use. If remaining residue in
the juicer dries up, it can make
disassembling and clean‑up difficult.
The excess build up can cause poor
performance in future uses.
• For easier disassembly, place the
top-set in the sink and run the water
through from the top of the top-set.
• Thoroughly dry the bottom of the
juicing screw where it connects to the
metal cylinder shaft on the base
HOW TO DISASSEMBLE AND CLEAN
Note • Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
• For easier clean up, operate the
juicer for an additional 30 seconds
after the juice is extracted.
• When the drum lid is stuck, press the
REVERSE-OFF-FORWARD button in
the order, switching back and forth
2 to 3 times to dislodge. Then place
hands on top of the drum lid and
firmly press down simultaneously
turning the drum lid counter clockwise
to open.
OPTIONAL | HOW TO USE THE FROZEN FRUIT STRAINER
CAUTION
When using the Frozen Fruit Strainer with frozen
fruit, slowly process small amounts perbatch.
• Do not use ice or process ingredients containing vegetable or animal oil. It may cause amalfunction.
• Remove hard seeds from the ingredients and peel the skins from the ingredients beforejuicing.
Note • When moving the appliance, donot
lift by grabbing the feeding tube.
Always lift the appliance by grabbing
the base or handle.
Lid
Juicing Screw
* use the same
juicing screw
from the Slow
Juicer
Frozen Fruit
Strainer
Juicing Bowl
Align the arrow from the lid with the
OPEN sign from the base and rotate
the top set clockwise until the arrow
from the lid is in CLOSE position.
Top set
Base
1Switch OFF and unplug the power cord
from the wall outlet.
2Turn the drum lid counter clockwise
toopen.
3Remove the bowl from the base.
4Remove the juicing screw, filter and
silicon wiper unit from the juicing bowl.
Clean with provided brush, using warm
soapy water.
5Place the juicing bowl under running
water and unplug the compression
silicone to clean the pulp spout.
TIP Soak the juicing bowl in a solution of
warm water with baking soda or little bit
of vinegar to clean any excess build up.
TIP Use the Frozen Fruit Strainer to make homemade
nut butter, hummus dip, baby food and more.

18 19
OPTIONAL | FROZEN INGREDIENTSOPTIONAL | HOW TO USE THE SMOOTHIE STRAINER
CAUTION
When juicing frozen ingredients, make sure to thaw your frozen ingredients for about 5 to 20
minutes before use.
(The required period to thaw the ingredients will depend on how long the ingredients were in the
freezer and the temperature it was kept in.)
• Please do not insert ingredients like ice, meat, oil or fat based ingredients. These ingredients may damage
the components.
• Please remove hard or thick seeds, pips, or peel before use.
HOW TO CLEAN THE SILICONE WIPERS
The silicone wipers are removable for cleaning. After cleaning, place the silicone wipers
back onto the frame as shown in the picture.
When making smoothie, add milk or other types of liquid between ingredients.
Check the consistency of the smoothie by looking through the juicing bowl, and add more liquid
asneeded.
• Thaw frozen ingredients like pomegranate and raspberry then insert about 1 tablespoon (5g)
atatime.
• Frozen ingredients usually lose significant amount of fluid when thawing. When juicing, mix milk or
yogurt to balance the fluid lost.
TIP Insert into the slot with
the tail pointing down.
Align the arrow from the lid with the OPEN
sign from the base and rotate the topset
clockwise until the arrow from the lid is in
CLOSE position.
Top set
Base
Lid
Juicing Screw
* use the same
juicing screw
from the Slow
Juicer
Smoothie
Strainer
Rotation Wiper
Juicing Bowl
1To assemble the top set, place the juicing
screw and the smoothie strainer in the juicing
bowl and close the lid.
1Insert the rotation wiper and the smoothie
strainer into the juicing bowl while aligning
the red dots of the smoothie strainer and
the juicing bowl.
2Insert the juicing screw into the Smoothie
Strainer with a twisting motion.
3Place the lid onto the juicing bowl by
aligning the red dots of the lid and the
juicing bowl. Then, rotate the lid clockwise
until the lid issecured.
• When using the Smoothie Strainer, make
sure the smart cap is closed to make a
better smoothie.
2Place the assembled top set onto the base.
TIP Use the Smoothie Strainer to enjoy delicious and healthy
smoothies and juice with a greater level of pulp.

20 21
TROUBLESHOOTING Q&A
When there is no power to the juicer:
• Check if the power cord is properly plugged in.
• Check if the drum lid and the juicing bowl are
properly assembled.
• Check if the top-set and the base are
properlyassembled.
• Juicer will not operate if parts are not
assembledproperly.
Low juice yield:
• Dierent ingredients hold dierent amounts of
fluid that will yield dierent amounts of juice.
• If the ingredients are not fresh, they may contain
reduced amounts of fluid, which will yield
lessjuice.
• Ensure the silicone compression is inserted
correctly (the compression silicone must be
inserted 40% into the slot below the pulp spout).
• If the ingredient itself has low water content, it
may help to soak it in water before juicing.
• If juicing ingredients with small seeds, after a
few servings, it may reduce the juice yield. For
best result, disassemble and wash the top-set in
between juicing.
• If there is seed residue on the bottom of the
strainer, this can aect juicer performance and
the overall juice yield.
There is too much pulp in the juice:
• When continuously juicing, and depending on
the ingredient, the juice may contain a lot of
finepulp.
• To reduce the fine pulp, clean the top-set
frequently to extract the pulp.
• Use a mesh strainer and put the juice through it
to collect the unwanted pulp.
• If the strainer and the screw are damaged
and aecting the juicer’s performance, it is
recommended the parts be replaced.
• The lifetime of each part may vary depending
on length and method of use and ingredients
extracted.
• If too many ingredients are inserted at the same
time, it may cause the juicer to stop frequently.
This can lead to pulpy juice. Insertthe
ingredients slowly and few at a time.
The drum lid will not close:
• Make sure the juicing screw is pushed all the
way in to the strainer in order for the drum lid to
close properly.
• If the juicing screw is not properly in position,
the drum lid may not close.
Odd noise from the juicer:
• Check if the parts are assembled correctly.
Try reassembling the parts and listen for the
odd noise.
• Do not start the juicer unless there are
ingredients and/or liquid in it.
• Operating the juicer without ingredients can
cause damage to the screw.
• If the juicer is operated without ingredients or
liquid, the noise level can increase and also can
lead to damage.
• The friction noise from the juicing screw and
the strainer will disappear when ingredients are
inserted into the juicer.
• The noise can occur if the juicer is operated
on an uneven or slanted surface. Place
the juicer on a horizontally flat surface
whenoperating.
The extracted pulp is very moist.
• During the very beginning of extraction, the
pulp can be more moist.
• Depending on the ingredient’s condition, the
extracted pulp can be aected; especially when
the ingredient is not fresh, the juice can be
extracted with the pulp.
During operation, the juicing bowl shakes.
• The juicing screw and the strainer are set up to
crush and squeeze the ingredients. It is normal
for the juicing screw and the strainer to vibrate.
• If the ingredient contains strong fibre, the
vibration from the top-set may be stronger.
TROUBLESHOOTING Q&A (CONTINUED)
During juicing, the juicer stopped:
• Check the power cord and make sure it is
plugged in correctly.
• Check that all the parts are correctly assembled.
• If too many ingredients are inserted at one time,
this can cause the juicer to stop.
• When the juicer stops because there are
too many ingredients inserted in it, press the
REVERSE-OFF-FORWARD button in this order,
switching back and forth 2 to 3 times.
• The reverse setting will push the ingredients
up, and the forward setting will pull the
ingredientsdown.
• If the juicer stops due to the overload
protection, let the juicer cool for 30 minutes to
2hours before juicing again.
• If there are hard seeds within the ingredients,
remove them before juicing. Hard seeds can
damage the juicer.
Layers of separation in the juice:
• Depending on the density of the ingredients,
the extracted juice may show layers of
dierent juices. It is dierent from separation
due to oxidation caused by juicing with a
high-speedjuicer.
The drum lid is stuck:
• After juicing, let the juicer operate for another
30seconds to extract the remaining pulp.
• If there are too much pulp in the top-set, this
can cause the drum lid to not open. In this
situation, press the REVERSE-OFF-FORWARD
button in this order, switching back and forth
2to 3 times.
• Pour water down the feeding tube to rinse out
the insides and then try opening the drum lid.
Juice dripping down the body of the base:
• If the compression silicone on the bottom of
the juicing bowl is not plugged in correctly, the
juice may seep out on to the juicer base. Before
assembling the parts, check and make sure the
compression silicone is inserted 40% into the
slot below the pulp spout.
Is it possible to juice ingredients with toughfibre?
• Ingredients like celery or ginger contain long
fibres that may wrap around the juicing screw
and aect the juicer’s performance. When
juicing fibrous ingredients, do not collect more
than 1 lb. of juice. After collecting this quantity
or less, clean the top-set completely before
juicingagain.
Discolouration of the plastic parts:
• After juicing, if the juicer is not cleaned right
away, the remaining pulp inside the top-set
can dry up which can make disassembling and
cleaning hard. This can also aect the juicer’s
performance and colour.
• Ingredients that are rich in carotenoids such
as carrots and spinach may dye plastic parts.
When the parts are dyed with carotenoids, rub
vegetable oil in to the dyed areas and use mild
detergent to clean.
• Vegetable oil should only be used during
clean‑up for parts that are discoloured. Do not
use vegetable oil on the juicing screw or the
strainer. If vegetable oil or oil from animal fat
gets on the juicing screw or the strainer, this
can aect the juicer’s performance and may
result in damaged parts.
• The silicone pieces on the top-set can be
detached to be thoroughly cleaned.
Using for purposes other than juicing:
• This juicer is designed to juice ingredients like
fruits and vegetables.
• Do not use the juicer for extracting
vegetableoil.
• Do not juice ingredients with high contents of
vegetable/animal oil.
• If vegetable/animal oil gets on the juicing screw
or the strainer, this can aect the performance
of the juicer and could result in damaged parts.

22 23
SPECIFICATIONS
Product Juicer
Model 600 - Whole Slow Juicer
Voltage 230-240Volt 50/60Hz
Power Consumption 240W
Rated working time 30-45 min
Rated interval time 3 min
Weight 9kg
Dimension 25 x 18.3 x 48.3 cm
Manufacturer Optimum Appliances
Type Vertical Cold-Press Masticating

24 25
CONTACTING US
Please contact the distributor located in the Country where you made your original purchase for
all Support, Servicing and Warranty.
Your distributor is:
Call to speak to one of our friendly Customer Service Representatives during business hours.
Australia 1300 309 900
New Zealand 0800 741 369
United Kingdom 0800 0789 055
United States 187 766 11851
24/7 After Hours Support, Appliances Faults, Repairs And Warranty.
Australia and New Zealand www.froothiesupport.com
United Kingdom www.froothieuk.supportsystem.com
United States www.froothiesupport.com
Europe www.froothiesupport.com
Customer feedback.
Australia [email protected]
New Zealand [email protected]
United Kingdom [email protected]
United States [email protected]
Europe [email protected]
TO FIND OUT MORE, VISIT FROOTHIE INTERNATIONAL
AND SELECT YOUR COUNTRY.
www.froothieinternational.com
WARRANTY TERMS & CONDITIONS (INTERNATIONAL)
Eective as of 1st January 2014
This warranty as outlined below solely covers distributors of the Optimum range of appliances. Please
contact your distributor for full product warranty.
1. Optimum® warrants this appliance to be free from defects in materials and workmanship and to perform
satisfactorily in household use for a period of 2 years from the date of purchase when used in accordance with
the accompanying instruction book.
2. Any warranties exceeding this standard period are oered as extended terms by the selling distributor and
claimable only though that provider.
3. Defects that occur within this manufacturer’s warranty period, under normal use and care will be repaired or
replaced at our discretion only if the selling distributor is unable to do so. This is done solely at our option
with no charge for parts. This warranty does not extend to accessories included or purchased separately.
Replacements can be oered for major faults as determined by your distributor and at their own discretion.
4. The strainers will only deteriorate or break through abuse and misuse are therefore are not covered by this
warranty for more than 30 days after purchase date.
5. In the event that the goods requiring repair are under warranty, and this distributor is unable to provide
the repairs; the customer is responsible for any freight charges to or from Optimum® (or their approved
serviceprovider).
6. Whilst in transit the goods are at the owner’s risk and any further damage during this transportation is not
covered under warranty.
7. Customers should ensure that the product being returned is properly packaged so as to ensure that no
damage occurs to the product during transit. To be able to process the warranty claim ensure you have
included an explanation of any problem, Optimum® will not fault-find and will only repair described faults as
covered under warranty.
8. This full warranty is void if this appliance has been subject to abuse, negligence, accident, alteration, failure to
follow operating instructions, or the product has been exposed to abnormal or extreme conditions.
9. Cosmetic changes that do not aect performance, such as discolouration of parts of the product in the
hands of the user or the eects of the use of abrasive cleaners will not be warranted or considered defects.
Thecleaning or removal of food products along with any damage caused by allowing them to build up is not
covered by this full warranty.
10. This warranty does not cover normal wear and tear of the product or parts.
11. This warranty does not cover any defect caused by an accident, misuse, abuse, improper installation or
operation, lack of reasonable care, unauthorized medication, loss of parts, tampering or attempted repair by a
person not authorized by Optimum®.
12. The warranty will not apply if damage, malfunction or failure resulting from alterations, accident, misuse, abuse,
fire, liquid spillage, maladjustment of customer controls, use on an incorrect voltage, power surges and dips,
thunderstorm activity, acts of God, voltage supply problems, tampering or unauthorized repairs by any persons,
use of defective or incompatible accessories, exposure to abnormally corrosive conditions or entry by any
insect, vermin or foreign object in the product.
13. You must keep your purchase receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase receipt must be presented when making a claim under this warranty.
14. In the event the receipt of purchase is not presented, then this warranty is invalid. Consumer Law allows us to
request reasonable proof of purchase to service a warranty claim.
15. This warranty does not imply, intend to or detract any consumer rights listed in and able to be enforced
from Regulated Consumer Law, any condition which is found to be in breach of the consumer law, the single
condition shall be void only and all other conditions remain in place.