Optimum 700 ADVANCED User manual

QUALITY YOU CAN TRUST
USER’SMANUAL
700 ADVANCED
COLD-PRESS JUICER

1
IMPORTANTSAFEGUARDS 1
PARTS&ACCESSORIES 3
ASSEMBLYINSTRUCTIONS 5
DIRECTIONSFORUSE 7
JUICINGTECHNIQUESFOROPTIMALRESULTS 9
TIPSANDPRECAUTIONSFORUSE 10
CLEANINGANDMAINTAININGYOURJUICER 11
OPTIONALHOWTOUSETHEHOMOGENISINGSTRAINER/BLANKPLATE 12
OPTIONALHOWTOUSETHECOARSE-HOLESTRAINER 13
OPTIONALFROZENINGREDIENTS 14
PRODUCTSPECIFICATIONS 14
HELP!SOMETHING’SGONEWRONG 15
WARRANTYTERMSANDCONDITIONS 16
CONTACTUS 17
CONTENTS IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed
including the following:
1. Read all instructions.
2. Always use this appliance on a dry, level surface.
3. To protect against electrical hazards, do not immerse cord, plugs or the appliance in
water or other liquid. Do not place on a wet surface.
4. Close supervision is necessary when any appliance is used by or near children.
Children should be supervised to ensure that they do not play with the appliance.
5. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
6. Unplug from outlet when not in use before putting on or taking o parts and
beforecleaning.
7. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner. Contact Customer Support
and Warranty.
8. The use of accessories or attachments not recommended or sold by the supplier
may cause fire, electrical shock or injury.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter, or touch hot surfaces.
11. Extreme caution must be used when moving an appliance containing hot liquids.
12. Do not use appliance for other than intended use.
13. Do not leave unit unattended while in use.
14. Always turn the appliance o and unplug from the outlet when left unattended or
finished using.
15. Check to be sure that the switch is in the OFF position after each use. Make sure the
motor is stopped before disassembling.
16. Avoid contacting moving parts. Make sure that the motor stops completely before
disassembling.
17. Always make sure the juicer is fully assembled and the juicer cover is locked
securely in position before the motor is turned on. Do not attempt to remove parts
when the juicer is in operation.
18. Do not either operate or plug and unplug the unit with wet hands.
19. Do not use the appliance continuously for more than 30-45 minutes.
20. Do not turn the appliance on for more than 2 minutes without adding food. This may
damage the auger.
21. Do not use this appliance if the strainer basket is damaged.
22. Do not put your fingers or other objects into the food chute while it is operation.
BEFOREUSINGYOUROPTIMUM700COLD-PRESSJUICER,
PLEASEREADTHESESAFETYINSTRUCTIONSCAREFULLY.

2 3
PARTS AND ACCESSORIESIMPORTANT SAFEGUARDS, CONTINUED
1. Hopper
2. Bowl Cover/Drum Lid
3. Juicing Screw
4. Coarse Strainer
5. Fine Strainer
6. Spinning Brush
7. Juice Bowl
8. Pulp Container
9. Juice Cup
10. Cleaning Brush
11. Pusher
12. Tofu Box and
Fabric Cloth
13. Strainer Attachment
14. Homogenising
Strainer/Blank Plate
15. Smart Cap
1
8
2
9
10
3
5
4
11
6
7
12
13 15
14
Always use the food pusher provided.
23. During operation feed the food slowly to avoid clogging. If the unit gets clogged
turn the appliance o immediately. Press the reverse function on the on/o switch. If
this does not work, press the on/o switch to the o position, unplug the appliance,
remove the cover and remove the stuck food.
24. Do not place on or near a hot gas or electric burner, or in a heated oven.
25. Always attach plug to appliance first, then plug cord into the wall outlet.
Todisconnect, turn any control to ‘OFF’, then remove plug from wall outlet.
26. Do not attempt to override the safety features.
SAVE THESE INSTRUCTIONS
Polarized Plug
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk
of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Donot modify the plug in any way.
FAILURE TO FOLLOW SAFETY INSTRUCTIONS AND WARNINGS COULD
RESULT IN SERIOUS INJURY. MISUSE OF YOUR JUICER MAY DAMAGE
YOUR APPLIANCE AND VOID YOUR WARRANTY.

4 5
PARTS AND ACCESSORIES, CONTINUED
1. Unlock Sign
2. Pulp Outlet
3. Bowl Dot
4. On/Rev Switch
5. Juice Bowl
6. Smart Cap
7. Easy Moving Grip
CHOICE OF STRAINERS
Coarse strainer
Coarse-hole Strainer is to juice soft fruit (strawberry, kiwi fruit & tomato)
or sticky material (bananas). The end result when using this strainer will
contain more pulp. (Nylon material)
Fine strainer
Fine-hole strainer is to juice hard fruit, beans & vegetables with fibres.
The juice will be smoother. (ULTEM/ PEI material)
Homogenising strainer/ Blank Plate
This specially designed blank plate can be used for grinding dry hard
food material (coee beans, almonds, etc.) It is also able to make frozen
fruit ice-cream and baby food.
(ULTEM/ PEI material)
1
3
4
5
6
7
2
PREPARATION:
1. Wash all the component parts before you start to assemble them.
2. Follow the directions below exactly as given. Your juicer may leak if you assemble
itincorrectly.
ASSEMBLY INSTRUCTIONS
1
1A
2
3
STEP 1: ASSEMBLE THE TOP PART OF THE JUICER
Place strainer inside the spinning brush
holder then add the spinning brush
into the juicing bowl. Line up the white
triangle on the strainer exactly with the
equivalent white triangle on the bowl.
Insert the juicing screw into the strainer.
Push it down firmly, and turn it until you
hear a click as it locks into place.
Place the compression silicone piece
partway into the slot beneath the pulp
spout. Ensure that most (around 60%) of
the silicone remains outside of the slot.
Position the juicing bowl on top of the
juicer base.

6 7
4
Open position
Closed position
STEP 2: ADD THE ASSEMBLED TOP PART TO THE BASE
To close the lid, hold the hopper in one
hand and the bowl in the other; then turn
the lid clockwise until the ‘lock’ mark and
triangle linesup.
Position the juice cup directly
beneath the juice outlet and the place
the pulp cup directly underneath the
pulp outlet.
IMPORTANT: the drum lid will not
close unless the juicing screw has
locked properly (see Step 3).
IMPORTANT: Never place your
fingers in the Food Chute.
DIRECTIONS FOR USE
Prepare your juicing ingredients. The wide mouth of your Optimum 700
Advanced means you don’t need to chop ingredients, but we do recommend
washing them first. Additionally:
For foods with hard seeds or pips (e.g. mango or stonefruit): remove any
hard parts from each ingredient before you juice it.
For leafy or fibrous vegetables (e.g. spinach or celery): separate the
leaves from the stems, and remove any tough, fibrous outer stems before
juicing the innerparts.
For frozen fruits and berries: ensure your ingredients are completely
thawed – beforejuicing.
NOTE: If you are unsure about which ingredients to use we recommend
following the recipes within the recipe book provided.
Plug the juicer in. If your hands are still wet from Step 1, ensure you dry them
before touching the power cord, plug or wall socket.
Start the juicer. Press the “On” button to turn the juicer on. While it remains
on, the juicer will slowly pull ingredients from the feeding tube into the
juicingbowl.
Insert the ingredients into the feeding tube one by one. Using the clip
positioned on the outer rim of the feeding tube unlock the safely lock which
provides access to the wide 8cm x 8cm feeding tube and self-feeding wings.
Insert larger ingredients such as whole apples and oranges (peeled or
unpeeled) into the wide tube with the assistance of the self-feeding wings.
The self-feeding wings are designed to lock into the safety position when not
in use and when using the smaller feeding tube.
Feed longer ingredients such as celery and kale into the smaller
feedingtube.
You may occasionally need to gently use the pusher to move ingredients
to the bottom of the feeding tube when using the smaller feeding chute.
Avoid using it continuously, however, or your juice quality may suer.
1
2
3
4
ASSEMBLY INSTRUCTIONS, CONTINUED

8 9
Turn the juicer o: keep the juicer running for at least 30 seconds after all
ingredients have been juiced, then press the “O” button. Note that the drum
lid may not open if any ingredients are left in the juicing bowl.
Use the smart cap, if required. The smart cap is designed to make your
Optimum 700 Advanced Cold-Press Juicer more versatile. With it, you can:
Make dierent types of juice within the same juicing process: when one
ingredient has finished juicing, close the smart cap, and add a glass of
water to the feeding tube. This will clean away any remaining tastes from
previous ingredients before you juice the next set.
Create mixed juices: make dierent mixed juice recipes by closing the
smart cap and selecting dierent ingredient options.
Stop the juicer from dripping: close the smart cap after the juicing
process has finished to stop any juice dripping out when you disassemble
the bowl.
6
5The Optimum 700 Advanced Whole Cold-Press Juicer is extremely versatile and
achieves great results every time. Please take the time to familiarise yourself with the
juicing techniques below for optimal results:
TECHNIQUE 1
Don’t press/shove food into the Optimum 700 Advanced Cold-Press Juicer
Do not apply a pushing/pressing/shoving force when inserting ingredients. Instead, simply
let your food fall into the “chewing juicing screw.” Virtually no force is necessary!
TECHNIQUE 2
Juice low-fibre plants first, and high-fibre plants last
When juicing fibrous ingredients a great tip for large leafy, stringy or fibrous vegetables is
to feed through gently, letting the juicing screw pull the ingredients into the juicer, using
the tamper only gently if required. It’s recommended that these ingredients are juiced last
as the fibres tend to accumulate in the ejection port in the juicing bowl at the bottom of
the juicing screw.
TECHNIQUE 3
Juice your juice!
If you find too much pulp in your juice, just pour the juice back through the machine again!
You’ll find that the second time through, nearly all the pulp is removed.
ITISIMPORTANTTOFOLLOWTHESETHREETECHNIQUESTOACHIEVETHEBESTRESULT
INYOUROPTIMUM700ADVANCEDJUICER.
JUICING TECHNIQUES FOR OPTIMAL RESULTS DIRECTIONS FOR USE, CONTINUED

10 11
TIPS AND PRECAUTIONS FOR USE
REMOVEHARDSEEDSBEFOREJUICINGFROMFRUITSLIKE:
PERSIMMONS,PEACHES,PLUMS, ETC.
HARDITEMS(KUDZUVINE,SUGARCANEETC.)ARENOTSUITABLE
FOR JUICING.
JUICERCANBEUSEDTOMASHGARLICANDPEPPERSWITHMOISTURE.
NOT SUITABLEFORGRINDINGDRY GRAINS.
WHENJUICINGHARDFRUITSORVEGETABLES,LIKECARROTS,THEY
MAYCAUSELOUDNOISES,THISDOESNOTINDICATEDAMAGETO
THE MACHINE.
BEAWARETHATJUICEMAYSPILLOUTWHENJUICINGFRUITSAND
VEGETABLELIKEGRAPESANDTOMATOES.
USINGFROZENFRUITSANDVEGETABLESMAYINFLUENCETHEFLAVOUR
OF JUICE.
FREQUENTLYJUICINGPROCESSEDANDHARDFOODSTUFFS(ICE,FRUIT
SEEDS,ETC.)MAYDAMAGETHESTRAINERS.PLEASEUSEWITH CARE.
THECONTINUOUSWORKINGTIMESHOULDBENOMORETHAN
30-45 MINUTES.
DRINKJUICESASSOONASPOSSIBLEAFTERJUICING,IFYOUWISH
TOSTOREJUICEPLACEITINASEALEDGLASSCONTAINERIN
THE REFRIGERATOR.
JUICINGTOOMUCHFOODORJUICINGHARDFOODSTUFFSMAYMAKEIT
DIFFICULTTOREMOVETHEHOPPERFROMTHEJUICINGBOWL.
IMPORTANT NOTE:
You will need to disassemble and clean your Optimum 700 Advanced Cold-Press Juicer
immediately after using it, every time you use it. If you allow the juicing residue inside it
to dry out, you will find it hard to disassemble and clean the juicer later on.
CLEANING AND MAINTAINING YOUR JUICER
Turn the drum lid counter clockwise
toopen.
1Switch o and unplug the juicer.
Never try to disassemble the
machine while the power cord is
plugged in.
Open the drum lid. Turn the lid
anticlockwise to open it, until the
‘unlock symbol’ and the triangle lines
up. If the lid is stuck, please refer to the
troubleshooting section.
Separate out and clean the juicing
components. Remove the spinning
brush holder, strainer and juicing screw
from the juicing bowl. Clean them in
hot, soapy water using the special juicer
brush provided.
Clean the juice bowl. Remove the
compression silicon from the slot (DO
NOT detach), then rinse the bowl in water.
Ensure the pulp outlet is rinsed clean,
then soak the bowl in a sink of warm
water with vinegar and/or baking soda
to remove any lingering residue.
Remove the base. Separate the juicing
bowl from the juicer base. Wipe down
the base with a damp cloth if required.
2
3
4
5
TIP: Ensure all components are completely dry before you put them away.

12 13
1To assemble, place the juicing screw and
the Homogenising Strainer/Blank Plate in the
juicing bowl and close the lid.
1Insert the Homogenising strainer/Blank
Plate into the juicing bowl aligning the
triangles of the strainer and juicing bowl.
2Insert the juicing screw into the
Homogenising Strainer/Blank Plate with a
twisting motion.
3Place the lid onto the juicing bowl by
aligning the triangles. Then, rotate the lid
clockwise until the lid is secured.
• When using the Homogenising Strainer/
Blank Plate, always leave the Smart
Cap and compression silicon open.
OPTIONAL | HOWTOUSETHEHOMOGENISINGSTRAINER/BLANKPLATE
• Do not use ice or process ingredients containing vegetable or animal oil. It may cause amalfunction.
• Remove hard seeds from the ingredients beforejuicing.
TIP Use the Homogenising Strainer/Blank Plate
to make homemade nut butter, hummus dip,
baby food and more.
Hopper
Juicing Screw
* use the same
juicing screw
from the Cold-
Press Juicer
Homogenising
Strainer/Blank
Plate
Juicing Bowl
OPTIONAL | HOWTOUSETHECOARSE-HOLESTRAINER
Hopper
Juicing Screw
* use the same
juicing screw
from the Cold-
Press Juicer
Coarse-hole
Strainer
Spinning brush
Juicing Bowl
1To assemble the top set, place the juicing
screw and the Coarse-hole Strainer in the
juicing bowl and close the lid.
1Insert the spinning brush and the
coarse-hole strainer into the juicing
bowl by aligning the triangles.
2Insert the juicing screw into the
Coarse-hole Strainer with a twisting
motion.
3Place the lid onto the juicing bowl by
aligning the triangles. Then, rotate the
lid clockwise until the lid is secured.
• When using the Coarse-hole
Strainer, make sure the smart cap is
closed to make a better smoothie.
TIP Use the Coarse-hole Strainer to enjoy delicious and
healthy smoothies and juice with a greater level of
pulp.
• Do not use ice or process ingredients containing vegetable or animal oil. It may cause amalfunction.
• Remove hard seeds from the ingredients beforejuicing.

14 15
OPTIONAL | FROZENINGREDIENTS
• Please do not insert ingredients like ice, meat, oil or fat based ingredients. These ingredients may damage
the components.
• Please remove hard or thick seeds, pips, or peel before use.
When making smoothie, add milk or other types of liquid between ingredients.
Check the consistency of the smoothie by looking through the juicing bowl, and add
more liquid asneeded.
• Thaw frozen ingredients like pomegranate and raspberry then insert about 1 tablespoon
(5g) atatime.
• Frozen ingredients usually lose significant amount of fluid when thawing. When juicing,
mix milk or yogurt to balance the fluid lost.
HELP! SOMETHING’S GONE WRONG
Check the below troubleshooting guide before calling for assistance or maintenance. If
you cannot resolve the issue please contact the supplier for support and service.
Troubleshooting when the device does not work:
A. Please check if the plug is correctly positioned.
B. Please check if all components are correctly
installed. Only when all components are
properly inserted / assembled can the device
be operated. Should the juicer made a strange
noise or not start please re-check assembly.
C. Please check hopper is securely locked in place
with juicing bowl; juicer will not start when this is
not done correctly.
The device does not work
• Make sure the power plug is correctly plugged
into the wall socket.
• Make sure the device is assembled correctly.
The device stops when juicing
• Please check power plug has not become lose.
• Please ensure you have not put in excessive or
hard foodstu into the juicer. Please check that
the device has not been working continuously
for too long.
Leaking from beneath juicing bowl
• Please check if the silicone stopper is plugged
insecurely.
The device shakes when juicing
• The motor rotation may cause it to shake slightly.
• Please ensure the device is on a level surface.
• Please ensure that the food is
preparedcorrectly.
Separation of juice
• Please note that some ingredients have dierent
density and you may note a slight separation
during juicing. Simply stir and enjoy.
Abnormal noise
• Please ensure to place the device on level
ofsurface.
• Check if the device contains excessive or overly
hard foodstus.
Dyed containers or accessories
• Please clean the device promptly after using
to prevent pulp leftovers from sticking to
thecontainers.
• The container or accessories may be stained
when juicing some foods containing rich
pigments. Clean it with cooking oil and then
withdetergent.
Hopper/lid is stuck
• Do not force it open.
• Make sure that no excessive pulp is left inside
the device. Please start the juicer to assist in
removing any build up.
• Check if any unidentified or hard objects have
been left inside. Use the reverse button to push
objects back up the feed tube.
PRODUCT SPECIFICATIONS
Product Juicer
Model 700 Advanced
Voltage 110-120V 60Hz
Power 200 Watts
Rated working time 30-45 min
Rated interval time 3 min
Weight 9.0kg
Dimension 240 x 165 x 443 mm
Type Vertical Cold-Press Masticating

16 17
WARRANTY TERMS & CONDITIONS
Eective as of 1st January 2014
This warranty as outlined below solely covers distributors. Please contact your distributor for full product warranty.
1. Optimum® warrants this appliance to be free from defects in materials and workmanship and to perform
satisfactorily in household use for a period of 2 years from the date of purchase when used in accordance with
the accompanying instruction book.
2. Any warranties exceeding this standard period are oered as extended terms by the selling distributor and
claimable only though that provider.
3. Defects that occur within this manufacturer’s warranty period, under normal use and care will be repaired or
replaced at our discretion only if the selling distributor is unable to do so. This is done solely at our option
with no charge for parts. This warranty does not extend to accessories included or purchased separately.
Replacements can be oered for major faults as determined by your distributor and at their own discretion.
4. The strainers will only deteriorate or break through abuse and misuse are therefore are not covered by this
warranty for more than 30 days after purchase date.
5. In the event that the goods requiring repair are under warranty, and this distributor is unable to provide
the repairs; the customer is responsible for any freight charges to or from Optimum® (or their approved
serviceprovider).
6. Whilst in transit the goods are at the owner’s risk and any further damage during this transportation is not
covered under warranty.
7. Customers should ensure that the product being returned is properly packaged so as to ensure that no
damage occurs to the product during transit. To be able to process the warranty claim ensure you have
included an explanation of any problem, Optimum® will not fault-find and will only repair described faults as
covered under warranty.
8. This full warranty is void if this appliance has been subject to abuse, negligence, accident, alteration, failure to
follow operating instructions, or the product has been exposed to abnormal or extreme conditions.
9. Cosmetic changes that do not aect performance, such as discolouration of parts of the product in the
hands of the user or the eects of the use of abrasive cleaners will not be warranted or considered defects.
Thecleaning or removal of food products along with any damage caused by allowing them to build up is not
covered by this full warranty.
10. This warranty does not cover normal wear and tear of the product or parts.
11. This warranty does not cover any defect caused by an accident, misuse, abuse, improper installation or
operation, lack of reasonable care, unauthorized medication, loss of parts, tampering or attempted repair by a
person not authorized by Optimum®.
12. The warranty will not apply if damage, malfunction or failure resulting from alterations, accident, misuse, abuse,
fire, liquid spillage, maladjustment of customer controls, use on an incorrect voltage, power surges and dips,
thunderstorm activity, acts of God, voltage supply problems, tampering or unauthorized repairs by any persons,
use of defective or incompatible accessories, exposure to abnormally corrosive conditions or entry by any
insect, vermin or foreign object in the product.
13. You must keep your purchase receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase receipt must be presented when making a claim under this warranty.
14. In the event the receipt of purchase is not presented, then this warranty is invalid. Consumer Law allows us to
request reasonable proof of purchase to service a warranty claim.
15. This warranty does not imply, intend to or detract any consumer rights listed in and able to be enforced
from Regulated Consumer Law, any condition which is found to be in breach of the consumer law, the single
condition shall be void only and all other conditions remain in place.
CONTACT US
Please contact the distributor located in the Country where you made your original
purchase for all Support, Servicing and Warranty.

OPT Juicer700 US Manual v3