PROAIM P-LLBT-150 User manual

1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
HD 150mm Bowl Baby Camera Tripod Stand w
Lever-Fricon and Aluminum Spreader (P-LLBT-150)
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
What’s In The Box
HD 150mm Bowl Baby Camera Tripod Stand
with Lever Fricon
Spanner Size: 13mm
Aluminium Spreader
Assemb ly Manua l

2
Aluminum Spreader Setup
• Extend the Spreader on the oor and loosen
all three knobs.
NOTE: The Spreader aaches to the spiked legs
of the spreader to provide precise customizaon
of the tripod's length and stability.
• Aer loosening the knobs, extend the
Spreader per your requirement.
• You can lock the posion using the locking
knobs present on each arm.
NOTE: The arms of the Spreader can easily
telescope out from 41cm/16” to 66cm/26”
radius, oering a broader footprint to create a
secure and steady base for the tripod.
Extendable adjustment via the provided locking knobs of Spreader

3
• Loosen all three adjustment knobs to set the
desired height of the Stand.
NOTE: One-stage telescopic design with fricon
knob extends up to 6 inches to capture
low-angle shots, and conversely, it can be easily
extended up to 34 inches for greater elevaon.
• Aer seng the height, ghten the knobs to
secure the Stand, as shown in the image.
NOTE: Locking pins on each leg secures the
adjusted height, prevenng them from
retracng under load.
• Unlock the red knob to adjust the Tripod’s legs
according to your requirement.
• Aer adjusng the Tripod legs, re-lock the
knob, as shown in the image.
• Mount the Tripod on the aluminum Spreader
by equally aligning them.
• Aer mounng the Tripod, properly secure it
using the rubber gripper.
150mm Bowl Baby Camera Tripod Stand Setup

4
Telescopic design provided with one-stage height adjustment

5
• Loosen the locking knob of the bowl uid
head (Not Included) and remove it.
• Now, mount the uid head on the Tripod
Stand.
• Tighten the locking knob to secure the uid
head.
• Press the yellow locking lever of the uid head
to unlock it.
• Aer unlocking the yellow locking lever,
remove the top plate of the uid head and
aach it to the Camera (Not Included) by
matching the threads.
• Secure the top plate and the Camera
(Not Included) using a screwdriver.
• Now, mount the Camera (Not Included) on the
uid head and properly lock it.
NOTE: The assembly of the whole setup is quick
and tool-less, saving you valuable producon
me.
• Tripod Stand works eciently with compable
devices such as Sliders, Jibs, and Geared
Heads with its 150mm bowl base.

6
YOUR PROAIM HD 150MM BOWL BABY CAMERA TRIPOD STAND W LEVER-
FRICTION AND ALUMINUM SPREADER
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon and
evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.