Protech Systems SP-6157 User manual

Ver. Q1
All Rights Reserved. Copyright 2018
Specification
SP-6157/6159
SP-6157/6159
Jumper Setting
SP-6157/
SP-6159
Quick
Reference
Guide
System
CPU Support Intel®Celeron®N3350 2C, 2.4Ghz
Intel®Pentium®N4200 4C, 2.5Ghz
Intel®AtomTM x7 E3950 4C, 2.0Ghz
Memory Support 1 x DDR3L 1600/1867 SO-DIMM socket, memory up to 8 GB
Drive Bay 1 x 2.5 inch SATAIII HDD or SSD drive space
Power Supply DC in 9~36V
Operating System Windows 10 loT Enterprise LTSB 2016 64bit / Ubuntu 16.04 LTS
Weight / Dimension SP-6157 : 7.1kg / 448mm(W) x 352mm(H) x 89mm(D)
SP-6159 : 10.7kg / 471mm(W) x 396mm(H) x 91.28mm(D)
Certificate FCC/CE
I/O Ports
Display 1 x HDMI (up to 4K), 1 x DVI-D
USB 3 x USB 3.0
Serial Port COM 1 / 2 for RS232 / 422 / 485 selectable by BIOS,
RI / 5V / 12V selectable by jumper
Antenna Hole 4 x antenna holes
Drive Bay 1 x 2.5 inch SATAIII HDD or SSD drive space
Expansion Slots 1 x Full-sized mini-PCIe(mSATA or 3G/4G card with USB 2.0 signal)
1 x Full-sized mini-PCIe(PCIe or 3G/4G card with USB 2.0 signal)
1 x SD slot / 2 x SIM slot
LAN 2 x LANs with PoE (IEEE 802.3af) as option, Wake-On-LAN, PXE
LAN 1: Intel®I210IT / LAN 2 : Intel®I210IT
Audio 1 x Line-out / 1 x MIC-In
Power On/Off 1 x power button, 1 x remote switch
LED 2 x PoE LED
I2C 1 x I2C port
Display
LCD SP-6157 : 17” TFT LCD(LED) Resolution SVGA 1280 x 1024, 350nit
SP-6159 : 19” TFT LCD(LED) Resolution SVGA 1280 x 1024, 300nit
Touch Screen 5-wire resistive touch screen (USB interface)
Environment
Operating Temp. HDD: 0°C ~ 40°C / SSD: 0°C ~ 50°C
(with air flow) Wide Temperature:
0°C ~ 50°C (without PoE and for N3350, N4200 only)
0°C ~ 45°C (with PoE and for N3350, N4200 only)
-20°C ~ 50°C (without PoE and for E3950 only)
-20°C ~ 45°C (with PoE and for E3950 only)
Storage Temp. -20°C ~ 80°C (-4°F ~ 176°F)
Humidity 20% ~ 90%
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly.
Replace batteries only with the same or equivalent type recommended
by the manufacturer. Dispose the used batteries according to the
manufacturer’s instructions.
JP_VDD1
31
JP7
20 19 1
1
2930
21
1
2
2
3
LVDS1
JINV1
JP6
PWR_BTN1
J_PBTN1
RST1 CN_POWER1
DVI1
HDMI1 USB2 USB1 LAN1 LAN2
AUDIO1
JDIO1
JP_I2C1
JPOE1
JI2C1
JI2C2
JLPC1
COM4 COM1
COM2COM3
LED1
JP_COM1
JP_COM2
JP_ATX1
JP_TPM1
JP10
SO_DIMM1
M_SATA1
M_PCIE1
JP4
SATA_PWR1
SATA1
1
2
16
18
52 51
17
15
16
18
52
2
1
17
15
51 1
3
1
2
1
2
5
6
666
1161 1
10 510 10 10
5 5 5
1
6
5
2
2
1
3 4
1
1
1
1
9
1
2
7
8
10
4
4
2
2
1516
12
5 6
1
2
9
10
1
2 3 54
25
22
R16
R14
R16
R14
R15
R13
R15
R13
R1
R7
R6
R12 R1
R7
R6
R12
L1 L2 L3 L4 L2 L3L1 L4
A1
A9
B1
B9
A4
A5
B4
B5
1
9
4
5
119
1
9
17
8
16
24
1
2
3
3
1
1
2
2
4
4
1
2
1
272
71
74
73
204
203
1
2
1 2
17
COM1 and COM2 PIN9
Definition Selection Guide
JP_COM2
JP_COM1
RI
12V
5V
51
6 2
2
(default)
1
2
5
6
1
2
5
6
51
6 2
2
1
2
5
6
1
2
5
6
Clear CMOS Data Selection
Normal Clear CMOS
(default)
11
TPM Module Selection
Normal Enable
(default)
11
I2C PIN2 VOLTAGE of
JI2C1 and JI2C2 SETTING
5
1
6
2
5
1
6
2
5
1
6
2
JI2C2 pin2JI2C1 pin2
3.3V
5V
(default)
5
1
6
2
AT / ATX Mode Selection
ATX AT
(default)
11
JP_EDP1
13
SW2

All Rights Reserved. Copyright 2017
Rear View (SP-6159)
(Unit: mm)
Top View
SP-6157 SP-6159
The following messages are reminders for safety on how to protect your system from damages and to extend a long life of the system.
1. Check the Cable Voltage
• The range of operating voltage should be between DC 9V and 36V. Otherwise, the system could be damaged.
2. Environmental Conditions
• Place your SP-6157 / SP-6159 on a sturdy, level surface. Be sure to allow enough space to have easy access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using 1SP-6157 / SP-6159 when it’s been left outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0°C ~ 40°C for HDD & 0°C ~ 50°C for SSD.
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because
condensation may come from inside of the system.
• Placing SP-6157 / SP-6159 in strong vigrations may cause hard disk failure.
• Don’t place the system close to any radio-active device in case of signal interference.
3. Handling
• Avoid putting heavy objects on top of the system.
• Don not turn the system upside down. This may cuase the floppy drive and hard drive to mal-function.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers
can open and disassemble the system. Please handle LCD and Touchscreen with extra care as they are easily breakable.
System Overview
Quick Setup HDD Easy Maintenance
Installing Panel Mount
Tighten the screws into the 12 mounting holes
(SP-6157) / 18 mounting holes (SP-6159) of the wall
fixture as shown to mount Panel PC onto the wall
securely. The panel mount installation is applicable for
both SP-6157 and SP-6159 Panel PCs.
Wall
The bottom-side hook is only available for SP-6157 $
SP-6159.
1. Install the bracket.
2. Tighten the screw.
Step 1. Install the hooks into the mounting hole
on the four sides of SP-6157 & SP-6159
using 8 pieces M3x5mm screws.
The top-side hook is only available for SP-6157 &
SP-6159.
SP-6157 & SP-6159
Step 2. Mount SP-6157 & SP-6159 Panel
PC equipped with 8 hooks onto
the wall firmly.
SP-6157 & SP-6159 SP-6157 & SP-6159
Step 3. The operation is the same as above.
Safety Precaution
Installing Hooks
Front View Rear View (SP-6157)
Rifgt Side View
SP-6157 SP-6159
Rear I/O View
Wall Mount Cut-out Dimensions
SP-6159 Wall
Wall
Wall
Installing Memory Heatsink
HDD & Memory and VESA Mount
Accessories
Memory Heatsink x 2
HDD Tray
M3 x 5 mm Screw x 4
Memory Heatsink
Installing VESA Mount
Step 2. Put the click on to secure.
Step 1. Attach the adhesive tapes on both
sides of the memory module.
Memory module
Adhesive tape
Unassemble the two
screws of HDD tray.
Step 1.
Pull out HDD tray.
Step 2.
Heed the mark should
be directed upwards when
you push back HDD tray.
Flip HDD tray to the
other side and release
the four screws.
Step 3.
M4 Nut
Hook
x 8 for SP-7157
Hook Accessories (option)
x 4 for SP-6157 & SP-6159
Mounting Brackets
M3x5mm screw
x 8 for SP-7157
M4x35mm screw
x 8 for SP-7157
x 8 for SP-7157
VESA Mount
VESA Mount Kit x 1
C.L.100(VESA)
130.5
100(VESA)
C.L.100(VESA)
448 (SP-6157)
471 (SP-6159)
352 (SP-6157)
396 (SP-6159)
100(VESA) 125.5
89
42
10
39
308 230
22
91.28
44.3
10
360 230 48
18
DVI-D HDMI
I
2
C
COM1
LAN1 LAN2
PoE ON
12
DC IN 9~36V
DVI-D
HDMI
USB
Connector
LAN1
LAN2
COM Connector
COM
Connector
Remote
Switch
I2C
Mic-in
Line-out
Power Button RESET DC IN 9~36V
COM2 GND VCC
Remote SW
404
217.5 435
217.5
421.5
410
138
325.5
314
106
4.7 Hole - 12X
449
439
276
92
192
364
374
4.7 Hole - 18X
SP-6157