Protech Systems SP-S214 User manual

Ver. Q2
All Rights Reserved. Copyright 2019
SP-S214
SP-S214
Jumper Setting
SP-S214
Quick
Reference
Guide
Specification
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly.
Replace batteries only with the same or equivalent type recommended
by the manufacturer. Dispose the used batteries according to the
manufacturer’s instructions.
System
CPU Support Core™ i7-7700T, Quad Core, 2.9GHz, 8M cache
Core™ i5-7500T, Quad Core, 2.7GHz, 6M cache
Core™ i3-7101TE, Dual Core, 3.4GHz, 3M cache
Celeron®G3930TE, Dual Core, 2.7GHz, 2M cache
Chipset Intel®Q170/H110
Memory Support 2 x DDR4 2133MHz SO-DIMM sockets (up to 32GB)
Storage 2 x 2.5" SATA III HDD/SSD (support RAID 0/1 in Q170 SKU only)
Power Input AC input ATX 250W
Operating System Windows 10 IoT Enterprise (64bit)
Dimensions (W x H x D) 585 x 377 x 107.15mm
System Weight 11.8kg
Mounting Support Wall mount / VESA75,100 / Panel mount
Certifications FCC / CE
I/O Ports
Display 2 x DVI-D
USB 4 x USB 3.0 / 4 x USB 2.0
Audio 1 x Line In / 1 x Line Out / 1 x Mic In
LAN 2 x RJ45 ports
LAN1: Intel®PHYI 219LM (10/100/1000 Mbps)
LAN2: Intel®LAN 210AT (10/100/1000 Mbps)
Support Wake-on-Lan, PXE
Serial Ports 4 COM ports / COM1 for RS-232/422/485
COM2/COM3/COM4 for RS-232
COM1/COM2/COM4 support +5V / +12V / RI selectable
Expansion Slots 1 x PCIe (x16) / 1x half-sized Mini PCIe
Power On/Off 1 x power button switch
1 x 2-pin connector for remote power button
Parallel Port 1 x Parallel Port (SPP/EPP/ECP)
Antenna Hole 2 x antenna holes
Display
LCD 21.5” TFT LCD(LED) resolution FHD (16:9) 1920x1080
Touchscreen 21.5” P-CAP touch panel
Environment
Operating Temp. HDD: 0°C~45°C (32°F~113°F) / SSD: 0°C~50°C (32°F~122°F)
Storage Temp. -20°C~80°C(-4°F~176°F)
Humidity 20%~90% (no condensation)
(default)
Disable
11
Enable
JP4 Intruder Detect
Selection
JP5 BIOS Recovery Mode
Selection
Configure Normal
(default)
1
1
1
Recovery
1
(default)
Enable Disable
1
SPI Override
Protection Selection
Normal
1
(default)
1
Clear CMOS
JCMOS1 Clear CMOS
Data Selection
11
JRTC1 Clear RTC Data
Selection
Normal (default)
Clear RTC Data
LAN2 Enable/Disable
Selection
Disable
Enable
(default)
1
1
COM1 RS-485 Auto Flow
Control Selection
(default)
Disable Enable
1
1
VCCIO Voltage Selection
0.95V 1.0V
(default)
1
1
AT/ATX Mode Selection
ATX
(default)
1
AT
1
COM4 Pin9 Voltage
Selection
2
1
12V
2
1
5
6
5V
RI
(default)
2
1
5
6
5
6
COM1 RS-232/422/485
Selection
RS-485
RS-422
RS-232
1
9
2
10
(default)
2
10
1
9
2
910
1
RTC1
1
910
B2
B82
1
AUDIO1
LAN2_USB2
LAN1_USB1 USB1 JD09M1
DVI1
ATX_PWR1
ATX_PWR2
PCI_E1
JP_LAN2
JP10
JP9
COM5
COM3
COM4 JP_COM2
JP_COM1
JP_COM4
JP11 JP6
SYS_FAN1
CPU_FAN1
JP3
SO-DIMM1
SO-DIMM2
USB2 SATA1
SATA2 JP1
FP1
JP12
JP4
JCMOS1
JP2
BAT1 M_PCIE1
LPT1
JP7
JP5
143 1
1
REMOVE
Intel
®
7th Gen.
Core™ i7/i5/i3
(LGA1151)
145
259
259
260
260 146 144
144
146
145 143 2
1
2
1
1
1
1
1
2
15
16 18 52
51
1
1
1
1
2
8
7
1
26
13
Intel®
H110/Q170
11
2
20
19
5
10
10
1
6
1
6
1
1
A2
A1
B1
A82
A81
B81
1517
1
13
24
12
1
6
1
6
56
5
34
12
12V
12V
GND
GND
15
2
6
1
12
COM6
1
7
14
5
DP1
17
2
15
6
COM1 Pin9 Voltage
Selection
5V
6
2
2
5
1
RI
(default)
1 2
56
12V
6
5
21
RI
(default)
5
6
COM2 Pin9 Voltage
Selection
5V
2
1 5
6
12V
2
1
AT/ATX Mode
Selection
AT
1
1
ATX
(default)

All Rights Reserved. Copyright 2017
(Unit: mm)
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the device.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special vacuum cleaner for computers.
• The power cord with the plug shall be connected to a socket-outlet with earthing connections.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
WARNING! Some internal parts of SP-S214 may have high electrical voltage. And therefore we strongly recommend that qualified engineers can open and disassemble the device.
Please handle LCD and Touchscreen with extra care as they are easily breakable.
Safety Precaution
Installing Hooks (optional)
Step 1. Install the mounting brackets into the mounting holes on
the four sides of SP-S214 using 12 screws (M3x5mm).
Step 2. Mount SP-S214 Panel PC equipped with 12 brackets
onto the wall firmly.
Quick Setup
Hook Accessories (optional)
x 12 M3x5mm screw
x 12
x 12
M4x35mm screw
Mounting Bracket
System Overview
Installing Wall Oring (optional)
Step 1. Place the Wall O-ring into
the back of the front bezel.
Hook
x 12
M4 Nut
x 12
Step 2. Fasten the 20 screws.
Wall Oring Accessories (optional)
M3x 28mm screw x 20 Washer x 20
Wall
Step 3. Install 12 hooks onto the mounting brackets on the four sides
of Panel PC and fasten the mating screws to secure firmly.
The following messages are reminders for safety on how to protect your panel PC from damages and extend the life cycle of SP-S214.
1. Check the Cable Voltage
• The range of operating voltage should be AC input ATX 250W. Otherwise, the panel PC could be damaged.
2. Environmental Conditions
• Place your SP-S214 on a sturdy, level surface. Be sure to allow enough space to have easy access around the device.
• Avoid extremely hot or cold place to install SP-S214.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the device from any heating device or using SP-S214 when it’s been left outdoors in a cold winter day.
• Avoid moving SP-S214 rapidly from a hot place to a cold place and vice versa because condensation may come from inside of the device.
• Don’t place SP-S214 close to any radio-active device in case of signal interference.
3. Handling
• Avoid putting heavy objects on top of the device.
• If water or other liquid spills into this product, unplug the power cord immediately.
Front View Rear View
Left Side View
Rear I/O View
Wall Mount Cut-out Dimensions
Top View
Right Side View
Bottom View
585
4-R2
377
549.2
532
368
184
341.2
324
171.2
20-Ø 3.5
4-R3
100(VESA)
55
75(VESA)
42.5
133.5
146
75(VESA)
100(VESA)
107.15
44.6
14.8
42.90
200.85
319.80
28.60
527.80
360
USB3.0COM1
DVI-D
USB 2.0
COM2 COM3
COM4
Remote
Switch
LAN1
LAN2
Mic In
Line In
Line Out LPT Power
Button
Wall O-ring
Wall
HDD Easy Maintenance
Step 3. Place the HDD / SSD and
fasten the four screws.
Step 2. P ull out the HDD / SSD tray.
Step 4. P ush back HDD / SSD tray.
Step 1. Release the screw of the
HDD / SSD tray.
Step 5. Fasten the screw of
the HDD / SSD tray.
Installing VESA Mount (optional)
HDD Accessories
M3x4.8mm Screw x 8
HDD Tray Screw
VESA Mount Accessories (optional)
VESA Mount Kit
VESA Mount (optional)
M4x10mm screw
x 4
VESA Mount Screw
M6x15mm screw
(Round Head with
spring washer screw)
x 4
x 1