Protech Systems SP-6555 User manual

Ver. Q1
All Rights Reserved. Copyright 2018
Specification
SP-6555/6557
SP-6555/6557
Jumper Setting
SP-6555/
SP-6557
Quick
Reference
Guide
System
CPU Type Intel®Celeron®N3350 2C, 2.4GHz
Intel®Pentium®N4200 4C, 2.5GHz
Intel®Atom®x7 E3950 4C, 2.0GHz
Memory Support 1 x DDR3L 1600/1867 SO-DIMM socket (up to 8 GB)
Drive Bay 1 x 2.5” SATAIII HDD or SSD drive space
Power Supply DC In 9~36V
Operating System Windows 10 loT Enterprise LTSB 2016 64bit / Ubuntu16.04 LTS
Weight / Dimensions SP-6555: 5.7kg / 364.3(W) x 278.8(H) x 78.2mm(D)
SP-6557: 6.5kg / 394.8(W) x 327.2(H) x 76mm(D)
Certificate FCC/CE
I/O Ports
Display 1 x HDMI (up to 4K), 1 x DVI-D
USB 3 x USB 3.0
Serial Ports COM1/2 for RS-232/422/485 selectable under BIOS
5V/12V/RI selectable by jumper
Antenna Holes 4 x antenna holes
Drive Bay 1 x 2.5” SATAIII HDD or SSD drive space
Expansion Slots 1 x Full-sized Mini PCIe(mSATA or 3G/4G card with USB 2.0 signals)
1 x Full-sized Mini PCIe(PCIe or 3G/4G card with USB 2.0 signals)
1 x SD slot / 2 x SIM slots
LAN 2 x LANs with PoE (IEEE 802.3af) as option, Wake-On-LAN, PXE
LAN 1: Intel®I210IT / LAN 2: Intel®I210IT
Audio 1 x Line Out / 1 x Mic In
Power On/Off 1 x power button, 1 x remote switch
LED 2 x PoE LED indicators
I2C 1 x I2C port
Display
LCD SP-6555: 15” TFT LCD(LED) Resolution XGA 1024 x 768
SP-6557: 17” TFT LCD(LED) Resolution SXGA 1280 x 1024
Touchscreen 5-wire resistive touchscreen or projected capacitive touchscreen
(USB interface)
Environment
Operating Temp. HDD: 0°C ~ 40°C / SSD: 0°C ~ 45°C
(with airflow) Wide Temperature SSD:
0°C ~ 50°C SSD (without PoE and for N3350, N4200 only)
0°C ~ 45°C SSD (with PoE and for N3350, N4200 only)
-20°C ~ 50°C SSD (without PoE and for E3950 only)
-20°C ~ 45°C SSD (with PoE and for E3950 only)
Storage Temp. -30°C ~ 60°C (-22°F ~ 140°F)
Humidity 20% ~ 90%
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly.
Replace batteries only with the same or equivalent type recommended
by the manufacturer. Dispose the used batteries according to the
manufacturer’s instructions.
JP_VDD1
31
JP7
1
2
2930
21
LVDS1
20 19
12
JINV1
1
3
JP6
PWR_BTN1
RST1 CN_POWER1
DVI1
HDMI1 USB2 USB1 LAN1 LAN2
AUDIO1
JDIO1
JP_I2C1
JPOE1
JI2C1
JI2C2
JLPC1
COM4 COM1
COM2COM3
LED1
JP_COM1
JP_COM2
JP_ATX1
JP_TPM1
JP10
SO_DIMM1
M_SATA1
M_PCIE1
JP4
SATA_PWR1
SATA1
1
2
16
18
52 51
17
15
16
18
52
2
1
17
15
51 1
3
1
2
1
2
5
6
666
1161 1
10 510 10 10
5 5 5
1
6
5
2
2
1
3 4
1
1
1
1
9
1
2
7
8
10
4
4
2
2
1516
12
5 6
1
2
9
10
1
2 3 54
25
22
R16
R14
R16
R14
R15
R13
R15
R13
R1
R7
R6
R12 R1
R7
R6
R12
L1 L2 L3 L4 L2 L3L1 L4
A1
A9
B1
B9
A4
A5
B4
B5
1
9
4
5
119
1
9
17
8
16
24
1
2
3
3
1
1
2
2
4
4
J_PBTN1
1
2
1
272
71
74
73
204
203
1
2
1
2
17
COM1 and COM2 PIN9
Definition Selection Guide
JP_COM2JP_COM1
RI
12V
5V
51
6 2
2
(default)
1
2
5
6
1
2
5
6
51
6 2
2
1
2
5
6
1
2
5
6
Clear CMOS Data Selection
Normal Clear CMOS
(default)
11
TPM Module Selection
Normal Enable
(default)
11
I2C PIN2 VOLTAGE of
JI2C1 and JI2C2 SETTING
5
1
6
2
5
1
6
2
5
1
6
2
JI2C2 pin2JI2C1 pin2
3.3V
5V
(default)
5
1
6
2
AT / ATX Mode Selection
ATX AT
(default)
11
1
3
JP_EDP1
SW2

All Rights Reserved. Copyright 2017
Rear View (SP-6557)
(Unit: mm)
Top View
SP-6555 SP-6557
The following messages are reminders for safety on how to protect your system from damages and to extend a long life of the system.
1. Check the Cable Voltage
• The range of operating voltage should be between DC 9V and 36V. Otherwise, the system could be damaged.
2. Environmental Conditions
• Place your SP-6555 / SP-6557 on a sturdy, level surface. Be sure to allow enough space to have easy access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using SP-6555 / SP-6557 when it’s been left outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0°C ~ 40°C for HDD & 0°C ~ 45°C for SSD.
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because
condensation may come from inside of the system.
• Placing SP-6555 / SP-6557 in strong vigrations may cause hard disk failure.
• Don’t place the system close to any radio-active device in case of signal interference.
3. Handling
• Avoid putting heavy objects on top of the system.
• Don not turn the system upside down. This may cuase the hard drive to mal-function.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers
can open and disassemble the system. Please handle LCD and Touchscreen with extra care as they are easily breakable.
HDD Easy Maintenance
Installing Wall Oring
Installing Memory Heatsink
SP-6555
Step 1. Install the mounting brackets into the
mounting holes on the four sides of
SP-6555 using 10 x M3x5mm screws.
Step 1. Install the mounting brackets into the
mounting holes on the four sides of
SP-6557 using 12 x M3x5mm screws.
SP-6557
Step 2. Mount SP-6555 Panel PC equipped
with 10 brackets onto the wall firmly.
Step 2. Mount SP-6557 Panel PC equipped
with 12 brackets onto the wall firmly.
SP-6555
SP-65557 SP-6557
Step 3. Install 10 hooks onto the mounting brackets
on the four sides of Panel PC and fasten the
mating screws to secure firmly.
SP-6555
Step 3. The operation is the same as above.
Pull out HDD tray.
Step 1.
mark should
Heed the
be directed upwards when
you push back HDD tray.
Release the four screws
of HDD tray.
Step 3.
Release the two
screws of HDD tray.
Step 2.
Hook
x 10 for SP-6555
x 12 for SP-6557
M3x5mm screw
x 10 for SP-6555
x 12 for SP-6557
M4x35mm screw
Safety Precaution
HDD & Memory & VESA Mount
Accessories
Installing Hooks
Front View Rear View (SP-6555)
C.L.100(VESA)
Right Side View
SP-6555 SP-6557
Left Side View
SP-6555 SP-6557
Rear I/O View
SS SS
SS
Remote SW
RESET DC IN 9~36V
COM2 GND VCC
DVI-D HDMI
I
2
C
COM1
LAN1 LAN2
PoE ON
1 2
DC In 9~36V DVI-D HDMI
USB
Connector
LAN1
LAN2
COM
Connector
COM
Connector
Remote
Switch
I
2
C
Mic In
Line Out
Power
Button
Wall Mount Cut-out Dimensions
SP-6555
Memory Heatsink x 2
HDD Tray
Screw
M3 x 5 mm Screw x 4
Memory Heatsink VESA Mount
VESA Mount Kit x 1
System Overview
Step 2. Put the click on to secure.
Step 1. Attach the adhesive tapes on both sides of the
memory module.
Memory module
Adhesive tape
click
C.L.100(VESA)
Quick Setup
Hook Accessories (option)
x 10 for SP-6555
x 12 for SP-6557
x 10 for SP-6555
x 12 for SP-6557
Mounting Brackets
394.8 (SP-6557)
278.8 (SP-6555)
327.2 (SP-6557)
364.3 (SP-6555)
Wall
1. Install the hook.
2. Tighten the screw.
88.8
88.5
C.L.100(VESA)
C.L.100(VESA)
78.2
270.5
31.2
5
76
5
SP-6557
357.5
217.5
387.5
217.5
76
29
Place the Wall
O-ring into the
groove surrounding
the back of the
front bezel.
Wall O-ring
Installing VESA Mount
Wall
360.5 0.3
R20
273.5 0.3
Wall
R20
390.3 0.2
313.5 0.2