Protech Systems SP-7165 User manual

Ver. Q1
All Rights Reserved. Copyright 2018
Specification
Jumper Setting
SP-7165/
SP-7167
Quick
Reference
Guide
SP-7165/7167
SP-7165/7167
System
CPU Support 6th/7th Gen. Intel®Core™ i7/i5/i3 & Pentium/Celeron®LGA1151
socket processor (CPU TDP max. up to 35W)
Chipset Intel®Q170/ H110
Memory Support 2 x DDR4 2133MHz SO-DIMM up to 32GB
Drive Bay 2 x 2.5” SATAIII HDD/SSD (support RAID 0/1 in Q170 SKU only)
Audio 1 x Line-in / 1 x Line-out / 1 x Mic-in
Expansion Slots 1 x Full-sized mini-PCIe (mini PCIe, USB and SIM signals)
1 x Half-sized mini-PCIe (mini PCIe and USB signals)
1 x SIM card slot /1 x CFast slot
Net Weight & SP-7165: 8.9 kg, 408mm x 320mm x 121.6mm
Dimension (WxHxD) SP-7167: 10.9 kg, 434mm x 366mm x 126.6mm
Power Input DC in 9~36V
Certificate FCC/CE
I/O Ports (Top side)
SIM card / CFast slot 1 x SIM card slot / 1x CFast slot
Reset / Antenna 1 x reset pin / 3 x antenna hole
I/O Ports (Bottom side)
Display 1 x DVI-I (DVI-D+VGA)
USB 4 x USB 3.0
Serial Port COM3/4 for RS232,
COM1/2 for RS232/422/485 (selectable by BIOS)
[COM1/2 for +5V/+12V/RI selectable by jumper]
LAN 2 x GbE LAN, Wake-On-LAN, PXE
LAN 1: Intel®PHY I219 LM (10/100/1000 Mbps)
LAN 2: Intel®LAN I210 AT (10/100/1000 Mbps)
Digital I/O Port 8 in / 8 out, DSUB-25 type or 16-pin terminal block (optional)
I2C Bus 1 x I2C bus port
Audio 1 x Line-in / 1 x Line-out / 1 x Mic-in
Power Input DC in 9~36V (DIN type 4-pin connector or 3-pin terminal block)
Power On/Off 1 x power button, 1 x remote switch
Display
LCD Panel Size SP-7165: 15” TFT LCD(LED) XGA (resolution: 1024 x 768)
SP-7167: 17” TFT LCD(LED) SXGA (resolution: 1280 x 1024)
Touch Screen 5-wire resistive touch screen or projected (USB interface)
Environment
Operating Temp. SSD: 0°C ~ 45°C (32°F ~ 113°F) (with PoE 0°C ~ 40°C (32°F -104°F))
(with airflow)
Storage Temp. -20°C ~ 80°C (-4°F ~ 176°F)
Humidity 20% ~ 90%
1
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly.
Replace batteries only with the same or equivalent type recommended
by the manufacturer. Dispose the used batteries according to the
manufacturer’s instructions.
CFast Voltage Control Selection
3.3V 5V
(default)
1
1
Flash Descriptor Override
Selection
Disable
1
1
Enable
DVI1
COM3
COM4
COM1
COM2
BIOS Recovery Mode
Selection
Normal
1
Recovery
1
Hardware Power Failure Selection
Disable
(default)
Enable
1
1
JP4
56
1
2
1
5
2
6JP15
JP12
12
JP7 13
DIO1
115
216
1
3
2
4ATX_PWR1
1 3
JP17
LED1
PWR_IN1
LAN1USB1
AUDIO1
12
3
4
I2C1
1
2
JP16
M_PCIE1
PWR_BTN1
PWR_BTN2
SATA2
SATA_PWR2
SATA1
SATA_PWR1
RST_SW1
1 3
JP9
CFAST1
JLPC1
HDDLED1
PWRLED1
PCI_E1
SO-DIMM1
M_PCIE2
CMOS1
1
1
2
2
1
2
15
16
17
18 52
51
1
2
15
16
17
18
51
52
12
1920
1
1
2
2
LAN2
12
COM1 Pin9 and COM2 PIN18
Definition Selection Guide
JP15JP12
RI
12V
5V
5
1
6
2
2
5
1
6
2
2
5
1
6
2
5
1
6
2
5
1
6
2
2
5
1
6
2
2
(default)
VCCIO Voltage Selection
0.95V 1.0V
(default)
1
Clear CMOS Data Selection
Normal Clear CMOS
(default)
11
LVDS1
12
2930
INV1
1
6
1
2
5
6
JP1
1
2
6
5
JP2
5
6
1
JP3
2
1280x1024
2CH/24bit
5
6
1
2
5
6
1
2
LVDS Resolution Selection
1024x768
1CH/24bit
(default)
JP1
5
6
1
2
JP2
5
6
1
2
LVDS Voltage Selection
5
6
1
2
5
6
1
2
+3.3V
(default)
+5V
SGN_BRD1

All Rights Reserved. Copyright 2017
Safety PrecautionSafety PrecautionSafety Precaution
System View
System Overview
SP-7165/7167
Installing 2nd Memory and SSD
DRAM CPU
M3 Screw*6
HEATSINK TOP COVER
Installing 1st Memory and CPU
Front View Rear View (SP-7167)
320 (SP-7165)
366 (SP-7167)
408 (SP-7165)
434 (SP-7167)
Rear View (SP-7165)
82.2
C.L.100(VESA)
100(VESA)
C.L.100(VESA)
98.2100(VESA)
SSD cable *2
M3 screw *6
Bottom Cover
SSD *2
M3 screw *4
SSD Bracket
SSD screw *8
DRAM
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries per the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. Therefore we strongly
recommend qualified engineers open and disassemble the system. The LCD and touch screen are easily
breakable, please handle them with extra care.
The following messages are safety reminders on protecting your system from damages and
extend a long life of the system.
1. Check the Cable Voltage
● The range of operating voltage should be between DC 9V and 36V. Otherwise, the system
could be damaged.
2. Environmental Conditions
● Place your SP-7165/SP-7167 on a sturdy & level surface. Be sure to allow enough space
to have easy access around the system.
● Avoid extremely hot or cold place to install the system.
● Avoid exposure to sunlight for a long period of time or in a airtight space. Also, avoid the
system from any heating device or using SP-7165/SP-7167 when it's been left outdoors
in a cold winter day.
● Note that the operating ambient temperature is 0~45°C for SSD.
● Avoid moving the system rapidly from a hot place to a cold one and vice versa because
condensation may come from inside of the system.
● Place SP-7165/SP-7167 in strong vibrations may cause hard disk failure.
● Do not place the system close to any radio active device in case of signal intereference.
3. Handling
● Avoid putting heavy objects on top of the system.
● Do not turn the system upside down. This may cause the hard drive to mal-function.
● If wate or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
● When the outside of the case is stained, remove the stain with neutral washing agent with
a dry cloth.
● Never use strong agents such as benzene or thinner to clean the system.
● If heavy stains are present, moisten a cloth with diluted neutral washing agent or alcohol,
and then wipe thoroughly with a dry cloth.
● If dust has been accumulated on the outside, clean it with a special vacuum cleaner made
for computers.
Bottom I/O View
Line-out
Remote
Switch
DIO
DC IN DVI-I
1
2
LAN
I2C
1
2
USB 3.0 MIC-in
Line-in
COM3
COM4
COM1
COM2
POE ON
Power
Button
Remote
Switch
DVI-I
DIO
1
2I2C
LAN USB 3.0 MIC-in
Line-out
Line-in
1
2
DC IN 9~36V
COM3
COM4
COM1
COM2
POE ON
Power
Button
SP-7165
(Right Side)
Side View
SP-7165
SP-7167
Wall Mount Cut-out Dimensions
SP-7165 SP-7167
SP-7167
(Right Side)
Top View
SP-7165/
SP-7167
(Left Side)
394
260
371
260
121.6
35
10.2
10.2
230
268
26
230
311.2 23.8
27.4
126.6
10.2 40
Wall
380.6
374
250
80
Ø3.5 (TYP.)
292.6
272
146
408.5
398
280
76
Ø3.5 (TYP.)
340.5
315
180
Wall