Protech Systems SP-6565 User manual

Ver. Q1
All Rights Reserved. Copyright 2018
Specification
SP-6565/
SP-6567
Quick
Reference
Guide
SP-6565/6567
System
CPU Support 7th/6th Gen. Intel®Core™ i7/i5/i3 & Pentium®/Celeron®LGA1151
socket processor (CPU TDP max. up to 35W)
Chipset Intel®Q170/ H110
Memory Support 2 x DDR4 2133MHz SO-DIMM socket up to 32GB
Drive Bay 2 x 2.5” SATAIII HDD/SSD (support RAID 0/1 in Q170 SKU only)
Audio 1 x Line In / 1 x Line Out / 1 x Mic In
Expansion Slots 1 x Full-sized mini-PCIe (mini PCIe, USB and SIM signals)
1 x Half-sized mini-PCIe (mini PCIe and USB signals)
1 x SIM card slot /1 x CFast slot
Net Weight & SP-6565: 8.2kg, 365.3 x 279.7 x 115.1mm
Dimensions (WxHxD) SP-6567: 9.1kg, 395.8 x 328.2 x 115.1mm
Power Input DC in 9~36V
Certificate FCC/CE
I/O Ports (Top side)
SIM card / CFast slot 1 x SIM card slot / 1x CFast card slot
Reset / Antenna 1 x Reset pin / 3 x antenna hole
I/O Ports (Bottom side)
Display 1 x DVI-I (DVI-D+VGA)
USB 4 x USB 3.0
Serial Ports COM3/4 for RS232
COM1/2 for RS232/422/485 (selectable under BIOS)
[COM1/2 for 5V/12V/RI selectable by jumper]
LAN 2 x GbE LAN, Wake-On-LAN, PXE
LAN 1: Intel®PHY I219 LM (10/100/1000 Mbps)
LAN 2: Intel®LAN I210 AT (10/100/1000 Mbps)
Digital I/O Port 8 in / 8 out, DSUB-25 type or 16-pin terminal block (optional)
I2C Bus 1 x I2C bus port (optional)
Audio 1 x Line In / 1 x Line Out / 1 x Mic In
Power Input DC in 9~36V (DIN type 4-pin connector or 3-pin terminal block)
Power On/Off 1 x power button, 1 x remote switch
Display
LCD Panel Size SP-6565: 15” TFT LCD(LED) XGA (resolution: 1024 x 768)
SP-6567: 17” TFT LCD(LED) SXGA (resolution: 1280 x 1024)
Touchscreen 5-wire resistive touchscreen or P-CAP touchscreen (USB interface)
Environment
Operating Temp. SSD: 0°C ~ 45°C (32°F ~ 113°F) (with PoE 0°C ~ 40°C (32°F -104°F))
(with airflow)
Storage Temp. -20°C ~ 80°C (-4°F ~ 176°F)
Humidity 20% ~ 90%
Jumper Setting
SP-6565/6567
1
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly.
Replace batteries only with the same or equivalent type recommended
by the manufacturer. Dispose the used batteries according to the
manufacturer’s instructions.
CFast Voltage Control Selection
3.3V 5V
(default)
1
1
Flash Descriptor Override
Selection
Disable
1
1
Enable
DVI1
COM3
COM4
COM1
COM2
BIOS Recovery Mode
Selection
Normal
1
Recovery
1
Hardware Power Failure Selection
Disable
(default)
Enable
1
1
JP4
56
1
2
1
5
2
6JP15
JP12
12
JP7 13
DIO1
115
216
1
3
2
4ATX_PWR1
1 3
JP17
LED1
PWR_IN1
LAN1USB1
AUDIO1
12
3
4
I2C1
1
2
JP16
M_PCIE1
PWR_BTN1
PWR_BTN2
SATA2
SATA_PWR2
SATA1
SATA_PWR1
RST_SW1
1 3
JP9
CFAST1
HDDLED1
PWRLED1
PCI_E1
SO-DIMM1
M_PCIE2
CMOS1
1
1
2
2
1
2
15
16
17
18 52
51
1
2
15
16
17
18
51
52
JLPC1
12
1920
1
1
2
2
LAN2
12
COM1 Pin9 and COM2 PIN18
Definition Selection Guide
JP15JP12
RI
12V
5V
5
1
6
2
2
5
1
6
2
2
5
1
6
2
5
1
6
2
5
1
6
2
2
5
1
6
2
2
(default)
VCCIO Voltage Selection
0.95V 1.0V
(default)
1
Clear CMOS Data Selection
Normal Clear CMOS
(default)
11
LVDS1
12
2930
INV1
1
6
1
2
5
6
JP1
1
2
6
5
JP2
5
6
1
JP3
2
1280x1024
2CH/24bit
5
6
1
2
5
6
1
2
LVDS Resolution Selection
1024x768
1CH/24bit
(SP-6565 default)
JP1
5
6
1
2
JP2
5
6
1
2
LVDS Voltage Selection
5
6
1
2
5
6
1
2
+3.3V
(15” default)
+5V
(17” default)
SGN_BRD1
17
11
1 2
19 20
17
S1 PC17
(SP-6567 default)

All Rights Reserved. Copyright 2017
Rear View (SP-6567)
(Unit: mm)
The following messages are reminders for safety on how to protect your system from damages and to extend a long life of the system.
1. Check the Cable Voltage
• The range of operating voltage should be between DC 9V and 36V. Otherwise, the system could be damaged.
2. Environmental Conditions
• Place your SP-6565 / SP-6567 on a sturdy, level surface. Be sure to allow enough space to have easy access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using SP-6565 / SP-6567 when it’s been left outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0°C ~ 45°C for SSD.
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because
condensation may come from inside of the system.
• Placing SP-6565 / SP-6567 in strong vigrations may cause hard disk failure.
• Don’t place the system close to any radio-active device in case of signal interference.
3. Handling
• Avoid putting heavy objects on top of the system.
• Don not turn the system upside down. This may cuase the hard drive to mal-function.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers
can open and disassemble the system. Please handle LCD and Touchscreen with extra care as they are easily breakable.
HDD Easy Maintenance
Installing Wall O-ring
Installing Memory Heatsink
SP-6565
Step 1. Install the hooks into the mounting holes
on the four sides of SP-6565 using 10 x
M3x5mm screws.
Step 1. Install the hooks into the mounting holes
on the four sides of SP-6567 using 12 x
M3x5mm screws.
SP-6567
Step 2. Mount SP-6565 Panel PC equipped
with 10 hooks onto the wall firmly.
Step 2. Mount SP-6567 Panel PC equipped
with 12 hooks onto the wall firmly.
SP-6565
SP-6567 SP-6567
Step 3. Install 10 mounting brackets onto the hooks
on the four sides of Panel PC and fasten the
mating screws to secure firmly.
SP-6565
Step 3. The operation is the same as above.
x 10 for SP-6565
x 12 for SP-6567
x 10 for SP-6565
x 12 for SP-6567
Pull out HDD tray.
Step 1.
mark should
Heed the
be directed upwards when
you push back HDD tray.
Release the four screws
of HDD tray.
Step 3.
Release the two
screws of HDD tray.
Step 2.
Safety Precaution
HDD & Memory & VESA Mount
Accessories
Installing Hooks
Front View Rear View (SP-6565)
Right Side View
SP-6565 SP-6567
Left Side View
SP-6565 & SP-6567
Bottom I/O View
Memory Heatsink x 2
HDD Tray
Screw
M3 x 5 mm Screw x 4
Memory Heatsink VESA Mount
VESA Mount Kit x 1
Installing VESA Mount
System Overview
Step 2. Put the click on to secure.
Step 1. Attach the adhesive tapes on both sides of the
memory module.
Memory module
Adhesive tape
click
SP-6565 and SP-6567
Top View
361.3 (SP-6565) / 395.8 (SP-6567)
Expansion
Slots (optional)
260
357.5 (SP-6565) / 387.5 (SP-6567)
151.1
122.6
5.5
28.5
CFast Reset
HDMI
USB
ANT
LPT
ANT
5V/GND/12V
DC OUT
COM5 COM6
ANT
SIM Card
The picture below illustrates the top view of SP-6565 and
SP-6567 equipped with the optional Expansion Slot.
Wall Mount Cut-out Dimensions
Wall
360.5 0.3
R20
273.5 0.3
SP-6565 SP-6567
M4 Nut
Hook
Hook Accessories (option)
x 10 for SP-6565
Mounting Brackets
x 12 for SP-6567
M3x5mm screw
x 10 for SP-6565
x 12 for SP-6567
x 10 for SP-6565
x 12 for SP-6567
M4x35mm screw
R20
390.3 0 .2
313.5 0.2
Wall
Quick Setup
DC IN DVI-I COM3 COM1
LAN1
LAN2
4 x
USB 3.0
DIO COM4 COM2 PoE1
PoE2
I
2
C
Power
Button
Remote
Switch
Mic In
Line Out
Line In
COM3 COM1
COM4 COM2
DVI-I
DC IN
Remote
Switch
DIO POE ON
I2C
1
2
1
2
LAN USB3.0
279.7 (SP-6565)
328.2 (SP-6567)
365.3 (SP-6565)
395.8 (SP-6567)
C.L.100(VESA)
C.L.100(VESA)
C.L.100(VESA)
C.L.100(VESA)
28.5
115.1
86.6
5.5
200
270.5
277.7
115.1
86.6
28.5
5.5
200
310.5
328.2
Place the Wall O-ring into the groove surrounding the back of
the front bezel.
Step 1.
Install the system onto the wall.
Step 2.
Wall O-ring
Wall
Place the Wall
O-ring into the
groove surrounding
the back of the
front bezel.
Install hooks onto the
four sides of the Panel PC.
1. Install the bracket.
2. Tighten the screw.
Wall
For SP-6565 / SP-6567Rx-x0x
For SP-6565 / SP-6567Rx-x1x
Power LED
HDD LED
Power
Button
Remote
Switch
(optional)
DVI-I
3-pin Terminal
Block DC IN
DIO
(optional)
COM3
COM4 COM2
COM1
I2C
(optional)
LAN2
(PoE optional)
4 x USB 3.0
Mic In
Line Out
Line In
PoE
Power
LED
LAN1
COM1
COM2
USB3.0
LAN
1
2
I2C
POE ON
1
2
COM3
COM4
DVI-I
DIO
DC IN 9~36V
Remote
Switch