Pulsarlube V series User manual

Remove contaminants around
the lube point.
Remove the grease nipple and install
appropriate adaptors.
Purge mode dispenses a large quantity of
grease in less than an hour. After the Purge
mode is used, reset the unit to the desired
dispensing period for further use.
Purge Mode
Log the installation date and the scheduled
date of lube cycle completion on the label
of the Pulsarlube V.
This product is a
disposible unit. Dispose
of remaining plastic
components complying
with local regulations for
recycling.
Warning
Do not cut, puncture, or reuse
lubricator. Do not change or
recharge the battery.
Select the dispensing period by pressing
the MODE button.
Once the dispensing period is set, screw
the mode cap back on.
When the selected dispensing period of
the Pulsarlube V has completed, remove
the lubricator from the application.
Installation/Disposal Guidelines
Turn the mode cap counterclockwise
and unscrew the cap.
Remove the protector.
Install the Pulsarlube V unit on the lube
point.
To avoid any potential injury or hazard, do
not tamper with the product.
Press the MODE button firmly to activate the
unit.
Note
Product Details
Mode Cap
Mode
Button
LCD
PCB
Screw Cap
Lubricant
Reservoir
Piston
Cylinder
Protector
Battery
Connecting Thread
(3/8" M BSPT)
High backpressure can cause a
delay in dispensing (must be under 5
bar).
If the product is installed at a 45°
or 90° angle, please use an angle
adapter with a diameter greater than
or equal to 1/4".
For remote installation using an 8mm
O.D. tubing, keep the maximum
distance at 1m (3ft) or less.
Mounting Installations
LCD Display
Each single press of the button
advances to the next setting as follows.
Ensure a clear passage using a manual
grease gun.
Note1
Remove any hardened grease
by purging the lube point with a manual grease gun.
Note2
The grease in the equipment and the grease
contained in the unit should be the same or compatible.
1
2
3
4 8 11
5 9 12
6 7 10

Rev.01
Bearing Shaft Diameter 125ml Dispensing Volume 250ml Dispensing Volume
121mm~305mm
_ _ _ _
105mm~120mm
_ _
1 month 8.3ml/day
89mm~104mm 1 month 4.2ml/day 2 month 4.2ml/day
80mm~88mm 2 month 2.1ml/day 3 month 2.8ml/day
64mm~79mm 3 month 1.4ml/day 6 month 1.4ml/day
51mm~63mm 6 month 0.7ml/day 12 month 0.7ml/day
25mm~50mm 12 month 0.3 ml/day
_ _
Pulsarlube V Standard Lubricants
Dispensing Recommendations
Ball & Roller Bearings
Below are some general guidelines for bearing lubrication requirements. Requirements
may vary with individual bearing types and operating conditions. Testing is recommended
for specific applications. Please contact yout distributor should you need any assistance in
setting proper dispensing rates.
Dispensing volumes (ml/day) are calculated assuming the lubricator is operating at
1 atm (14.7 psi), 20˚C. Output volume may vary with ambient temperature changes,
atmospheric pressure changes, consistency of lubricant, or any resistance or
backpressure existing at the lube point (bearing or passage).
User Manual
Product Certifications
Certifications
Mounting Methods
The Pulsarlube V is designed for single point
lubrication only. Direct mount is always
preferable. For applications not allowing
any direct mounts, remotely mount the unit
using appropriate accessories and keep
the distance from the lube point as short as
possible.
For remote installation using a tube, use an
8mm O.D. (5/16") tubing pre-filled with the
same or compatible grease as the grease
contained in the unit. Keep the maximum
distance at 1m (3ft) or less.
Shelf life and Product Warranty The shelf life of the Pulsarlube V unit is 1 year from the date of
production. Product warranty is limited to original defects in material and workmanship and will not
cover any collateral damage due to mishandling, abuse and/or any other inappropriate use of this
product. Warranty period is 1 year from the date of purchase.
Warning If possible, please avoid using remote installation when the unit is set at the
12 month dispensing period due to low pressure.
Warning This product is a disposible unit. Please replace with a new unit once set
dispending period has completed.
The World Leader of Automatic Lubrication
Grease Grease Type Description
Excellent extreme pressure lubricant
containing solid lubricants
Superior high speed (over 3,000 rpm)
or high DN lubricant
NSF H1 registered food grade lubricant
High oxidation stability lubricant
Multipurpose lubricant fortified with extreme
pressure additives and MoS
Synthetic lubricant for extreme low temp
applications (below 15˚C)
High vibration-resistance lubricant
High performance multipurpose lubricant
Multi Purpose with MoS
Low Temperature
High Temperature
H1 Food Grade
High Speed
Heavy Duty
Multi PurposePL1
PL2
PL3
PL4
PL5
PL6
PL7
PL10 Electric Motor Bearing
Note
Cl. I, Div. 1, Gps. A, B, C, and D hazardous
Temp. Code T4, -25°C ≤ Ta ≤ +55°C
22
Pulsarlube USA, Inc.
TEL:[phone] FAX :[phone] www.pulsarlube.com / [email protected]
1480 Howard Street, Elk Grove Village, IL 60007, USA