Regency Racetrack LCTRT7135 User manual

PROBLEMS OR QUESTIONS?
Call us at 866-816-9822 or email [email protected]
www.regencyof.com
PG.1
Legacy Racetrack Conference Table
LCTRT7135, LCTRT9543, LCTRT12047
BEFORE YOU ASSEMBLE:
• Place all parts on a clean, smooth surface to avoid scratching the parts
• Check to be sure you have all parts & hardware
• Remove all wrapping materials, including any staples & packing straps
• Keep all hardware, small parts & packaging out of reach of children
PARTS:
E: SCREWS (x32)
G: CORNER
BRACKETS (x4)
I: CAM LOCK
COVERS (x14)
F: CAM PINS (x14)
H: FLAT
BRACKETS (x2)
J: DPEL (x1)
A:TABLE TOP (x2)
B: STRINGER (x1)
C: LEGS (x2) D: SUPPORTS (x2)
HARDWARE:
FIGURE 1:To open Cam Lock, point arrow
toward Cam Pin Hole. To close and lock
Cam, turn clockwise

PROBLEMS OR QUESTIONS?
Call us at 866-816-9822 or email [email protected]
www.regencyof.com
PG.2
Legacy Racetrack Conference Table
LCTRT7135, LCTRT9543, LCTRT12047
STEP 1: Insert (3) Cam Pins (F) into each Leg (C). Two
go on the inside, and one on the outside.
STEP 3: Attach Supports (D) to outside of both
Legs (C) by lining up the Cam Pin (F) with the Cam
Lock on Support (D). Drop into place and tighten
Cam Locks as shown in Figure 1.
STEP 2: Attach Stringer (B) to Legs (C) by lining up
Cam Pins (F) with Cam Locks on Stringer (B). Secure
into place and tighten Cam Locks as shown in Figure 1.
C
F
B
F
CD
C
F
Inside of LEG (C)
Outside of LEG (C)
C
C
C
STEP 4: Place both Table Tops (A) face down on
a clean, carpeted surface and insert (4) Cam Pins
(F) into each Top (A). Please note: pre-drilled hole
locations for pins vary by model.
F
A

PROBLEMS OR QUESTIONS?
Call us at 866-816-9822 or email [email protected]
www.regencyof.com
PG.3
Legacy Racetrack Conference Table
LCTRT7135, LCTRT9543, LCTRT12047
STEP 7A: Attach Corner Brackets (G) using (4)
Screws (E) each where Table Top (A) & Stringer (B)
meet.
OPTIONAL STEP 7B: Cover Cam Locks using Cam
Covers (I).
STEP 8a: With two people, carefully flip assembled
table over and set upright.
STEP 5A: Push both Table Tops (A) together, and
secure with Sash Locks—Rotate handle into the “ON”
position until it locks into place.
STEP 5B: Attach Flat Brackets (H) between Table
Tops (A) using (4) Screws (E) per Flat Bracket (H).
A
A
H
E
E
B
G & E G & E
A
E
I
STEP 6: Using two people, move the assembled base
onto the Table Tops (A), lining up each Cam Pin (F)
on the Table Top (A) with a Cam Lock on the base.
Tighten all Cam Locks once base is in position
A
A
B
CC
STEP 8a: Insert DPEL (J) into precut hole and attach
using (2) Screws (E).
J
A A
J