Regency MLD723048 User manual

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
IMPORTANT NOTICE:
● Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
● Check to be sure that you have all parts and hardware.
● Remove all wrapping materials, including staples & packing straps before you start to assemble.
● Do not tighten all screws/bolts until completely assembled.
● Keep all hardware parts out of reach of children.
MLD723048, MLD723042, MLD663048, MLD663042 - INSTRUCTIONS
Hardware:
M) Screws(21) ● N) Washers(8) ● O) Bolts(16) ● P) Glides(5)
Parts:
A) Top Bracket(2) ● B) Foot Bracket(2) ● C) Back Support(2) ● D) Front Support(2) ● E) Exterior Leg Cover(2) ● F) Interior Leg
Cover(2) ● G) Corner Leg ● H) Flat Bracket ● I) Long Modesty ● J) Short Modesty ● K) Long Table Top ● L) Short Table Top
NOTE: Back Supports differ from Front Supports with additional holes for modesty attachment.
Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and a rubber mallet.
ABC G
I
J
K
L
M N O P
DEFH

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
MLD723048, MLD723042, MLD663048, MLD663042 - INSTRUCTIONS
STEP 1: Insert 2 Glides(P) into each of the Foot Brackets(B). STEP 2: Insert 1 Glide(P) into the Corner Leg(G).
P
G
B
P
P
BEFORE STARTING STEP 3A-B, NOTE THE HOLE PLACEMENT IN FIGURE 1.
The set of three holes on each of the Front Supports and Back Supports should face in toward one another.
STEP 3A: Assemble Legs by inserting Back Supports(C) into each Foot Bracket(B).
NOTE: Modesty Holes on Back Supports should face interior side as shown below.
STEP 3B: Now insert the Front Supports(D) into each Foot Bracket(B). Then insert each Top Bracket(A) into the Front
Supports(D) and Back Supports(C). Finally, attach the Foot Brackets(B) and Top Brackets(A) to the Front Supports(D) and Back
Supports(C)with 4 Bolts(O) per Leg.
NOTE: Do not tighten bolts until all bolts have been started.
Left Leg
(interior side)
Right Leg
(interior side)
CC
BB
Modesty Holes
DD
A A
Figure 1
OO OO
OO OO

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
MLD723048, MLD723042, MLD663048, MLD663042 - INSTRUCTIONS
STEP 4A: Snap the Interior Leg Cover(F) into Back Support(C) and Front Support(D) using a rubber mallet.
NOTE: Interior Leg Cover is installed on the side with the modesty holes.
STEP 4B: Snap the Exterior Leg Cover(E) into Back Support(C) and Front Support(D) using a rubber mallet.
CD
Modesty Holes
F E DC
FOR STEP 6A, USE THE TEMPLATE INCLUDED WITH INSTRUCTIONS.
STEP 6A: Place the Long Table Top(K) on a clean at surface with desired table nish face down. Then align your template as shown
below for the Corner Leg placement. Mark the coordinating points.
STEP 6B: Attach Corner Leg(G) using 3 Screws(M). See Figure 2.
NOTE: Edges of template
align with edges of table.
For a Left ReturnFor a Right Return
Figure 2
M
G
M
STEP 5: CHOOSE THE ORIENTATION FOR YOUR L-DESK (LEFT RETURN or RIGHT RETURN).
NOTE : PRODUCT IS REVERSIBLE.
THE FOLLOWING STEPS INCLUDE BOTH RIGHT AND LEFT ORIENTATIONS.
Hardware placement is critical.
K

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
MLD723048, MLD723042, MLD663048, MLD663042 - INSTRUCTIONS
STEP 7: Place 1 Washer(N) on each of 2 Bolts(O). Then attach the Short Modesty(J) to the Corner Leg(G) using 2 Bolt/
Washers(Figure 3). Now, attach the coordinating Leg to the Short Modesty(J) using two more Bolt/Washer combinations.
NOTE: The lip on the Modesty should face the interior side of the desk.
GG
J J
(N,O)
For a Right ReturnFor a Left Return
Right Leg Left Leg
Figure 3
STEP 8: Align the Leg to the edge of the Long Table Top(K).
Then attach the Leg using 2 Screws(M).
K
M
M
STEP 10: CAREFULLY FLIP THE ASSEMBLED PORTION
OF THE TABLE UPRIGHT WITH TWO OR MORE PEOPLE.
STEP 9: For additional support, attach the Short Modesty(J) to
the desktop with 2 Screws(M).
J
MM

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
MLD723048, MLD723042, MLD663048, MLD663042 - INSTRUCTIONS
STEP 11: Place 1 Washer(N) on each of 2 Bolts(O). Then attach the Long Modesty(I) to the Corner Leg(G) using 2 Bolt/Washers
and support the modesty by attaching the coordinating Leg to the Long Modesty(I) using two more Bolt/Washer combinations.
NOTE: The lip on the Modesty should face the interior side of the desk.
For a Right ReturnFor a Left Return
G
I
G
I
STEP 12A: Connect the Short Table Top(L) to the Long Table Top(K) on the underneath side of the desk using the Flat Bracket(H)
and 10 Screws(M).
STEP 12B: Align the Leg with the back edge of the Short Table Top. Then attach the Leg using 2 Screws(M).
STEP 12C: For additional support, attach the Long Modesty(I) to the desktop with 2 Screws(M).
L
K
H
K
L
For a Right Return
For a Left Return
Figure 4
M
MM
M
K
L
Right LegLeft Leg

ALIGN THIS CORNER FOR A LEFT RETURN
USE WHITE POINTS FOR HOLE PLACEMENT ALIGN THIS CORNER FOR A RIGHT RETURN
USE BLACK POINTS FOR HOLE PLACEMENT