Reison Nordiska 10-366 User manual

10-366 Edit.2 Page 1( 4)
USERS MANUAL
ELBOW SUPPORT
10-366
GMDN 35393
PID 59665

10-366 Edit.2 Page 2( 4)
INTRODUCTION
The elbow support is intended to be a support for the elbows of the surgeon at such operations where
a support is needed. I.e. eye surgery or other kinds of micro surgery.
ABOUT USER MANUAL
This user manual is for clinical personnel, service personnel and others who need the knowledge
about and understanding of how the support works and how it can be used.
Read the user manual carefully before use of the equipment.
Always follow the instructions in user manual.
Always keep the user manual close to the equipment.
IMPORTANT SECURITY DIRECTIONS
Avoid collisions between the elbow support and other equipment when the operating table is
moved or is transported.
A functional control shall always be done before every time of use.
Service and preventing maintenance shall always be done by authorized personnel and in
issued intervals.
The elbow support is designed for a maximum load of 25kg. To keep the safety factor
according to the European standards EN 60601 and EN 60601-2-46, the maximum load shall
not be exceeded.
INSTALLATION
At the unpacking, check that there are no damages to the equipment. Check against the delivery note
that all parts are delivered ant that there are no loose parts in the box. The packing material consists
of cardboard and plastic and can be recycled.
CARE AND MAITENANCE
Be aware of that adjustments and all kind of repair only can be done by for this purpose educated
personnel. Changing of any part of the construction without a written permission from the
manufacturer is strictly forbidden. Transgression will be prohibited.
Cleaning
Clean with mild soap detergent with PH 6-8 and tempered water. Dry with soft cloth. If
necessary, use alcohol on metal parts. Do not use detergents containing strong acids or
bases.
Control
Check daily for any kind of damages and check all locking functions before use.
Annual service
Once a year the elbow support shall be carefully cleaned and moving parts shall be
lubricated with water resistant grease. The locking functions shall be checked and
if necessary adjusted.

10-366 Edit.2 Page 3( 4)
GENERAL DESCRIPTION
SPARE PARTS
Turning of the complete arm is done by loosen the lock
lever anticlockwise. Set the desired position and lock by
turning the lever clockwise
The elbow support can be set in different positions laterally
and longitudinally by turning the lock lever to the left. Set
desired position and lock by turning the lever to the right.
The elbow support locks to the accessory rail
by turning the lever to the left or to the right.
Height adjustment is done by loosen the lever
anticlockwise. Set desired height and lock by
turning the lever clockwise.

10-366 Edit.2 Page 4( 4)
TECHNICAL DATA
Height 30cm
Width 20cm
Length maximum extended 64cm
Weight 3,5kg
Maximum load 25kg
Box 240 Eriksbergsvägen 32 A
734 25 Hallstahammar
Sweden
Phone: [phone] Fax: [phone]
E-mail: [email protected]e
www.reison.se
1. Inner arm 10398 1pc.
2. Pivot fitting 10300 1pc.
3. Outer arm 10399 1pc.
4. Post, weld assembly 10400 1pc.
5. Pad 10425 1pc.
6. Lock lever GN 300 78 S M8x16 1pc.
7. Washer 10004 4pcs.
8. Screw MF6S 6x12 A2 4pcs.
9. Snap ring SGA 18 2pcs.
10. Sleeve 10483 1pc.
11. Snap ring SGA 16 1pc.
12. Wood screw TKT 5x16 4pcs.
13. Clamp housing 10031 1pc.
14. Spacer 10526-A 1pc.
15. Guide 10053 1pc.
16. Adjustable lock lever 6593-65 1pc.
17. Screw MC6S 6c45 FZ 2pcs.
18. Shaft 10009 1pc.
19. Plunger 10711 1pc.
20. Lock lever 10648 1pc.
21. Spring 10013 1pc.
22. Pressure pin 10012 1pc.
23. Eccentric 11165 1pc.
24. Ball K20 M8 S 1pc.
25. Nut left threaded 10302 1pc.
26. Lock lever 10304 1pc.
27. Set screw MSK6SS M4x5 A2 1pc.
28. Set screw MSK6SS M5x8 A2 1pc.
29. Screw 10303 1pc.
30. Nut right threaded 10301 1pc.
31. Ball K20 M6 S 1pc.