Reison 10-387 User manual

1
Armboard 10-387 including versions
Version
Description
10-387
Rotation clamp (EU 25x10 mm rail)
10-387-UK
Rotation clamp (UK 1¼ ” x ¼ ” rail)
10-387-US
Rotation clamp (US 1⅛ ’’ x ⅜ ’’ rail)
10-387-AUSTRALIA
Rotation clamp (AUS 1 ½ ’’ x ¼ ’’ rail)
10-387-F
Rotation clamp (EU 25x10 mm rail), incl. moulded pad
10-387-F-UK
Rotation clamp (UK 1¼ ” x ¼ ” rail), incl. moulded pad
10-387-F-US
Rotation clamp (US 1⅛ ’’ x ⅜ ’’ rail), incl. moulded pad
10-387-H
Rotation clamp (EU 25x10 mm rail), incl. Medisoft pad
10-387-UK-H
Rotation clamp (UK 1¼ ” x ¼ ” rail), incl. Medisoft pad
Warning! This symbol indicates important information related to safety. Follow these
instructions carefully.
Read User Manual before use! It is important to fully understand the content of the user
manual before attempting to use the equipment.
2020-10-30
Document number: M10-387EN rev.01
Armboard 10-387
ENGLISH

2
Intended use
Armboard intended for placing and positioning the patients arm for e.g. medication during surgery.
The product is to be used by medical professionals within a medical facility.
Safety regulation
Maximum load: 12 kg in even distribution, corresponding to a patient weight of 200 kg, according to
EN 60601-1 and EN 60601-2.
Before use, ensure correct function!
When loosening the lock lever to adjust the height, support underneath the armboard, to prevent it
from uncontrolled descend into the bottom position.
Remove the armboard or secure it over the operating table, during transport!
For use during diathermy procedures, the cushion must be fixed to the plate by using e.g. Velcro straps,
to prevent from sliding. The complete device needs to be covered with e.g. sterile bag, to prevent the
patient to come in contact with the metal parts.
Service and preventive maintenance shall be performed by authorized personnel.
MAX 12 kg (MAX 200 kg )

3
User instruction
Installation
Position adjustment
1.
2.
90o
A.
B.
A.
A.
B.
B.

4
Maintenance
Do not place in dishwasher! The lock mechanism will be destroyed by corrosion in the ball joint. For
cleaning instruction, please, read “Cleaning” in this manual.
Service, preventive maintenance, adjustment and repair shall be performed by authorized personnel
only. Altering the construction without a written consent from the manufacturer, is strictly forbidden.
Adjusting the lock mechanism
Tool: 3 mm hex key.
To turn 1/8 of a round is enough for adjustment.
Complete lock should be achieved when the lever is at rest.
Too strong lock may lead to damage in case of e.g. collision.
Adjusting the lever position
Tool: 3 mm hex key.
Weaker lock
Stronger lock
A.
B.
C.

5
Cleaning
Clean with antiseptic detergent with pH 6 –8 and warm water. Ethanol can be used. Wipe dry with
soft cloth. Do not use strong acidic or alkaline detergent.
To avoid malfunction do not use detergents in the ball joint! The oil film in the ball joint shall not be
removed. Damp a soft cloth with antiseptic detergents or alcohol to clean the ball joint. Wipe it dry.
The ball joint device shall be oiled with hydraulic oil ISO VG32 or similar.
Control
Check that there are no loose parts and that there is no damage to any part. The lock function is
checked by locking and unlocking the top in different positions. If a cushion is used check that it is clean
and is not damaged.
Annual service
Once a year the arm board shall be carefully cleaned, moving parts shall be lubricated, the locking
function shall be tested and, if necessary, the ball joint shall be adjusted.

6
Spare parts
Version:
10-387
10-387-F
10-387-H
Description
Pcs.
Article no.
Article no.
Article no.
1.
Ball joint locking device
1
10021
10021
10021
2.
Plate
1
10020
10020
10020
3.
Screw MFX-Z A4-70 M4x10
4
-
-
-
4.
Washer
1
10004
10004
10004
5.
Clamp body
1
EU:10031
US:10547
UK:10543
AUS: 10567-Aus
EU:10031
US:10547
UK:10543
EU:10031
US:10547
UK:10543
6.
Gear plate
1
10486
10486
10486
7.
Guide
1
10320
10320
10320
8.
Gear ring
1
10316
10316
10316
9.
Screw MKFXS M4x10 A2
1
-
-
-
10.
Lock handle
1
10346
10346
10346
11.
Stud
1
10429
10429
10429
12.
Set screw MT6SS M5x6 A2
2
-
-
-
13.
Screw MC6S M6x30 FZ
2
-
-
-
14.
Shaft
1
10009
10009
10009
15.
Spring
1
10013
10013
10013
16.
Preassure pin
1
10012
10012
10012
17.
Plunge
1
10711
10711
10711
18.
Eccentric
1
11165
11165
11165
19.
Låsspak
1
10014
10014
10014
20.
Ball
1
K20M8S
K20M8S
K20M8S
21.
Screw MF6S M6x12 A
1
-
-
-
22.
Washer DB 5x10x0,5 A2
1
-
-
-

7
Accessories
Armboard:
10-387
10-387-F
10-387-H
Article no.
Description
10-381
Flat comfort cushion
x
x
x
10-382
U-shaped moulded cushion
x
x (incl.)
x
10-382-H
U-shaped comfort cushion
45mm
x
x
x (incl.)
10-382-HT
U-shaped comfort cushion
70mm
x
x
x
10-383
Armboard strap
x
x
x
10-383-L
Armboard strap long
x
x
x
Technical specification
Maximum work load
12 kg in even distribution, corresponding to a patient weight of 200 kg,
according to EN 60601-1 and EN 60601-2
Weight
4,3 kg
Material armboard
Stainless steel
Version
UDI-DI
Dimension
(H x W x L)
10-387
07350111830595
229 x 180 x 670 mm
10-387-UK
07350111830663
229 x 180 x 670 mm
10-387-US
07350111830687
229 x 180 x 670 mm
10-387-AUSTRALIA
07350111830601
229 x 180 x 670 mm
10-387-F
07350111830618
229 x 180 x 670 mm
10-387-F-UK
07350111830625
229 x 180 x 670 mm
10-387-F-US
07350111830632
229 x 180 x 670 mm
10-387-H
07350111830649
229 x 180 x 670 mm
10-387-UK-H
07350111830670
229 x 180 x 670 mm

8
Reison Medical AB
Eriksbergsvägen 32A
734 92 Hallstahammar
SWEDEN
[phone] [e-mail] [e-mail]