RIGHT ANGLE NewHeights 4 NZP Series User manual

Read all the instructions before beginning.
Fax: [phone]
Hardware Pack # 53433
www.raproducts.com
Page1 OF 7Instruction # 53440
Version Dated: 7/11/16
K&A Manufacturing
6703 Zinser Street
Schofield, WI 54476
Phone: [phone]
NewHeights™ Series 4 NZP
Levante Crank Height
Adjustable Conference able

800934
Half Size
53055
801235
Half Size
51708
Page 2 OF 7
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Tools Required for Assembly:
Power Driver W/Adjustable Torque
#2 Phillips Head Driver Bit or
#2 Square Head Driver Bit
3/16" Hex Head Driver Bit or
Allen Wrench
Tape Measure
Level
Hardware Pack 53433
Hardware Is Drawn Actual Size
I EM # PAR # DESCRIP ION Q Y.
1 Varies NewHeights Levante Worksurface 1
2 801303 30" Levante Conf able Left Leg Assembly Leg A 1
3 801302 30" Levante Conf able Right Leg Assembly Leg B 1
4 51708 M5 x 18mm (7/8") Sq/Ph/Wshr Head Wood Screw 34
5 801235 ube Leg o Diff. Drive ube 2.04" 1
6 801247 Series 4 Levante Deflection Gear/Brake/Bracket Assembly 1
7 53013 Split Lock Washer 1/4" 2
8 53055 Socket Head Cap Screw 1/4-20 x 7/16 2
9 Varies Series 4 Levante Extruded Internal ooth Profiled ube 1
10 Varies Series 4 Crank Handle 1
11 53141 S 4 Crank Handle Clamp 1
12 53638 5/16-18 x 3/8 Button Head Socket Screw 8
13 Not Used
14 Varies NewHeights Series 4 Cross Support 2
15 800934 Cross Support End Cap 4
16 Varies L U-Channel 1
17 801347 S 4 Crank Bracket Assembly 1
53013
Instruction # 53440
712
15
5
8
4
53638

Instruction # 53440 Page 3 OF 7
located on one of the leg assemblies.
Fax: [phone]
6703 Zinser Street Schofield, WI 54476
www.raproducts.com
Phone: [phone]
2
K&A Manufacturing
The drawing below shows how to distinguish the left leg A from the right leg B.
Warranty Information: NewHeights™ products are warranted to be free of defects due
to manufacturing or materials as follows: Three years on the gears, Five years on the
support brackets, aluminum columns and feet. We will replace any defective part after
inspection by an authorized agent. Costs incurred due to product replacement such as
installation labor and transportation are not covered under this warranty. When
corresponding with RightAngle™ Products, provide the model and serial numbers
3
Leg A Left Leg
Part numbers are marked
801303
on the worksurface supports.
Hole for the tube
drive must face the
inside of the table.
Leg B Right Leg
801302
Hole for the tube
drive must face the
inside of the table.

Phone: [phone]
assembly and tighten the screw.
Page 4 OF 7
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
www.raproducts.com
Fax: [phone]
Step 1: Lay the worksurface 1on a protected surface
with the pilot holes facing up. Align the holes in the crank
bracket 17 with the pilot holes in the worksurface. Attach it
with (4) wood screws 4. Do not over-tighten the screws.
Use a low torque setting on the power driver.
Step 2: Place the right leg assembly 3(Leg B) on the
worksurface 1with the worksurface support facing down.
See Page 3 to determine which leg assemblies are right
hand and left hand. Insert the short drive tube 5into the
gear drive near the top of the leg assembly. Insert the
gear drive on the gear drive assembly 6into the other
end of the short drive tube.
Step 3: Place (2) lock washers 7on (2) socket screws
8. Insert these through the holes in the gear drive
assembly 6. Thread them into the cage nuts pre-
installed in the worksurface support. Hand tighten.
Step 4: Place the clamp 11 onto the hex rod on the
drive assembly. Slide the leg assembly 3forward
guiding the hex rod on the gear drive assembly 6
through the bracket assembly 17 . Align the holes in the
worksurface support with the pilot holes in the worksurface
1. Slide the crank handle through the bracket assembly
and onto the hex rod on the gear assembly. Set it at 1/8"-
1/4" from the edge of the worksurface. See Detail A. Slide
the clamp 11 forward against the back of the bracket
Instruction # 53440
Steps 1-4
B
7
8
Detail B
1
10
17
4
3
5
6
5
11
10
1
Detail A
11
17
1/8"-1/4"

K&A Manufacturing
www.raproducts.com
Page 5 OF 7
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
Step 5
guiding the
other end of the main drive tube into the gear drive near the
supports with the pilot holes in the worksurface.
top of the leg assembly. Align the holes in the worksurface
3
2
9
Step 5: Slide one end of the main drive tube 9onto the
gear drive on the gear drive assembly 6.Place the left leg
assembly 2(Leg A) on the worksurface 1
6

15 14
12
Step 7
Both legs.
each cross support.
Page 6 OF 7
Instruction # 53026
Step 6: With the help of an assistant align the
cross support 14 with the stickers on both leg
assemblies. See below. Insert (4) socket
screws 12 through the holes in the ends of the
cross support and thread them into the weld
nuts that are held in place by the stickers. Do not
fully tighten. Check that the cross support is level
and parallel to the worksurface. Fully tighten the
socket screws. Repeat step 7 with the remaining
cross support.
Step 7; Insert (2) end caps 15 into the ends of
Step 6

pilot holes in the worksurface
Phone: [phone]
with the
to the worksurface with (6) to (12) wood screws 4
1
Fax: [phone]
Carefully remove the black socket screw from
each leg assembly. See Detail E. Stand aside in case
Instruction # 53440 Page 7 OF 7
. Attach the u-channel
.
6703 Zinser Street Schofield, WI 54476
www.raproducts.com
Step 10:
K&A Manufacturing
Step 8: Attach the leg assemblies 2and 3to the
worksurface 1with (16) wood screws 4. Do not
over-tighten the screws. Use a low torque setting on
the power driver.
Step 9: Align the holes in the u-channel 16
the components are not properly
assembled and attached. This releases
the gas assist components inside the leg
assemblies. At this point, fully tighten the
cap screws holding the gear drive assembly
to the worksurface supports. With the help
of an assistant, set the workstation upright
in its final location. Level the workstation if
required by turning the leveling glides clock-
wise (from the top) on the low corners of the
unit. If your workstation has casters, level it
by turning the bolts at the top of the casters.
Steps 8 & 9
Leveling Glide
Black
Socket
Screw
Detail E
removing the screws.
WARNING!
Cylinders inside
the leg assemblies are under
pressure. Stand clear of leg
assemblies when removing the
screws in Step 10. Read the
instructions thoroughly and
complete the assembly before
Step 10
16
4
4