RIGHT ANGLE NewHeights 4 XT Series User manual

SUPPORT
WORKSURFACE
9
8
4
5
7
1
STEPS 2-5
6
READ ALL THE INSTRUCTIONS
BEFORE BEGINNING. DO NOT
OPERATE THE UNIT UNTIL IT IS
FULLY ASSEMBLED
1
3
4
5
2
DETAIL A
7
4.000
PRE-INSTALLED
WELD NUT
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
PAGE 1 OF 3
VERSION DATED: 1/20/14
TOOLS REQUIRED FOR ASSEMBLY:
CORDLESS DRILL
#2 P ILLIPS EAD DRIVER BIT
#2 SQUARE EAD DRIVER BIT
7/32" EX EAD DRIVER BIT OR
ALLEN WRENC
TAPE MEASURE
LEVEL
N wH ights SERIES 4 XT CONFERENCE TABLE ASSEMBLY INSTRUCTIONS:
STEP 1: DO NOT ALLOW T E LEG ASSEMBLIES TO STAND WIT OUT SUPPORT.
T EY CAN TIP OVER AND T E GEAR OUSING COULD CRACK. PLACE (2)
LOCK WAS ERS 4 ON (2) SOCKET SCREWS 5 . INSERT T ESE T ROUG T E
OLES IN T E LEFT SUPPORT BRACKET 3 AND T READ T EM INTO T E WELD
NUTS INSIDE T E MOTOR BOX. DO NOT FULLY TIG TEN. REPEAT STEP 1 WIT
T E RIG T SUPPORT BRACKET AND T EN REPEAT T IS STEP WIT T E SECOND
LEG ASSEMBLY.
STEP 2: LAY T E WORKSURFACE 6 ON A PROTECTED SURFACE WIT T E PILOT
OLES FACING UP. ALIGN T E OLES IN T E WORKSURFACE SUPPORTS AND
T E SUPPORT BRACKETS WIT T E PILOT OLES IN T E WORKSURFACE. WIT
T E ELP OF AN ASSISTANT, PLACE (4) LOCK WAS ERS 4 ON (4) SOCKET
SCREWS 5 . INSERT T ESE T ROUG T E OLES AT T E ENDS OF T E CROSS
SUPPORT 7 AND T READ T EM INTO T E WELD NUTS PRE-INSTALLED IN T E
GROOVES ON T E LEG ASSEMBLIES 1 . SEE DETAIL AT LEFT.
STEP 3: LEVEL T E CROSS SUPPORT 7 AT 4" FROM T E BOTTOM OF T E WORK-
SURFACE SUPPORTS AND FULLY TIG TEN T E SOCKET SCREWS
5 . SEE DETAIL A.
INSERT AN END CAP 8 INTO EAC END OF T E CROSS SUPPORT. REPEAT
STEPS 2 AND 3 WIT T E OT ER CROSS SUPPORT.
STEP 4: ATTAC T E LEG ASSEMBLIES 1 TO T E WORKSURFACE USING (16)
WOOD SCREWS 9 . FULLY TIG TEN. DO NOT OVER-TIG TEN T E SCREWS.
USE A LOW TORQUE SETTING ON T E DRILL.
STEP 5: FULLY TIG TEN T E (8) SOCKET SCREWS 5 T AT ATTAC T E SUPPORT
BRACKETS 2 AND 3 TO T E MOTOR BOXES.
INSTRUCTION # 53219 HARDWARE PACK # 53218
ITEM # PART # DESCRIPTION QTY.
1 VARIES XT CENTERED LEG 2
2 801131 XT MOTOR BOX SUPPORT ANGLE RIG T 2
3 801132 XT MOTOR BOX SUPPORT ANGLE LEFT 2
4 53025 5/16 LOCK WAS ER 16
5 53024 5/16-18 x 1/2 BUTTON EAD SOCKET SCREW 16
6 VARIES CONFERENCE TABLE WORKSURFACE 1
7 VARIES SERIES 4 CROSS SUPPORT 2
8 800934 CROSS SUPPORT END CAP 4
9 51708 M5 x 18mm SQ/P /WS R EAD WOOD SCREW VARIES
10 VARIES U-C ANNEL 2
11 50298 New eights CONTROL BOX 1
12 50285 New eights AND SWITC 1
17 51951 WIRE MANAGEMENT J 1
STEP 1

COLUMN 1 WIRE
STEP 9
RUN WIRING IN T E WIRE MANAGEMENT J
S OWN ERE FOR CLARITY.
AND T E U-C ANNELS W IC ARE NOT
AND SWITC WIRE
WIRE RUNS DIAGRAM
COLUMN 2 WIRE
AND SWITC COLUMN 1 COLUMN 2
912
13
11
M1
10
STEPS 6-8
PAGE 2 OF 3
VERSION DATED 1/20/14
STEP 6: ALIGN T E OLES IN T E CONTROL BOX 11 AND T E AND SWITC 12 WIT T E PILOT OLES IN T E
WORKSURFACE 6 . ATTAC T EM WIT (4) WOOD SCREWS 9 . T ESE COMPONENTS CAN BE MOVED IF
REQUIRED.
STEP 7: ALIGN T E OLES IN T E U-C ANNELS 10 WIT T E PILOT OLES IN T E WORKSURFACE 6 . ATTAC
T EM WIT ( 20-24) WOOD SCREWS 9 .
STEP 8: ATTAC T E WIRE MANAGEMENT J 13 AT T E LOCATION S OWN USING (1) WOOD SCREW 9 . NO
PILOT OLE IS PROVIDED.
STEP 9: PLUG T E WIRE FROM T E AND SWITC INTO T E S RECEPTACLE ON T E CONTROL BOX 11 . PLUG
T E MOTOR WIRES INTO T E CABLES AND PLUG T E OT ER ENDS INTO T E M1 AND M2 RECEPTACLES ON T E
CONTROL BOX.
STEP 10: WIT T E ELP OF AN ASSISTANT, SET T E TABLE UPRIG T IN ITS FINAL LOCATION. LEVEL T E TABLE IF
NECESSARY BY TURNING T E LEVELER GLIDES CLOCKWISE (FROM T E TOP) ON T E LOW CORNERS OF T E
TABLE. IF YOUR TABLE AS CASTERS, LEVEL IT BY TURNING T E BOLTS AT T E TOP OF T E CASTERS.
S M2
WIRING DIAGRAM
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING

AND SWITC
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
PAGE 3 OF 3
VERSION DATED 1/20/14
RESET PROCEDURE: PRESS T E DOWN ARROW UNTIL T E WORKSURFACE REAC ES ITS LOWEST
POSITION AND CLICKS. T E New eights™ CONFERENCE TABLE IS NOW READY FOR USE.
TROUBLESHOOTING: IF YOU ARE AVING ANY PROBLEMS WIT T E TABLE OPERATION, CONTACT
RIG TANGLE™ SERVICE AT 800-298-4351 OR [email protected]m.
WARRANTY INFORMATION: New eights™ PRODUCTS ARE WARRANTED TO BE FREE OF
DEFECTS DUE TO MANUFACTURING OR MATERIALS AS FOLLLOWS: 2 YEARS ON T E GEAR AND/OR
MOTOR INCLUDING T E CONTROL BOX AND AND SWITC . 5 YEARS ON T E SUPPORT BRACKETS,
ALUMINUM COLUMNS AND FEET. WE WILL REPLACE ANY DEFECTIVE PART AFTER INSPECTION BY AN
AUT ORIZED AGENT. COSTS INCURRED DUE TO PRODUCT REPLACEMENT SUC AS INSTALLATION
LABOR OR TRANSPORTATION ARE NOT COVERED UNDER T IS WARRANTY. W EN CORRESPONDING
WIT RIG TANGLE™ PRODUCTS, RECORD AND PROVIDE T E MODEL AND SERIAL
NUMBERS LOCATED ON T E CONTROL BOX.