RIGHT ANGLE NEWHEIGHTS Series 4 XT Parts list manual

Page1 OF 9Instruction # 53210 Hardware Pack # 53209
K&A Manufacturing
6703 Zinser Street
Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Version Dated 8/4/16
Read all the instructions before beginning.
NewHeights™ Series 4 XT
Elegante 3-Leg Workstation
Assembly/Operation Instructions
Failure to comply with or observe all assembly, safety, and operation
instructions and warnings regarding the use of this product may result
in serious property damage or bodily injury.
Make sure no obstacles are in the desk's path and all cords are of appropriate
length for the desk. Always maintain a 1" clearance around the table to prevent
pinching.
Never assemble (or disassemble) the table or components with the table plugged
into a power outlet. This product is for use on a nominal 120-volt circuit and has
a grounding plug. Make sure that the product is connected to an outlet having the
same configuration as the plug. No adapter should be used with this product.
Duty Cycle: 2 minutes ON/18 minutes OFF
Workstation can continuously operate for a maximum duration of two minutes.
After two minutes of non-stop operation, the workstation will automatically stop
and require eighteen minutes of cool down.

Left Return
Front
4
Note: Motor box
faces inside of
table
Leg B Right Leg
Right Return
Note: Motor box
faces inside of
table
Front
4
Leg A Left Leg
Page 2 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Your workstation will have either (2) left legs (Leg A) and (1) right leg (Leg B) or
(2) right legs (Leg B) and (1) left leg (Leg A). The drawing below shows how to
distinguish the left leg A from the right leg B.
Instruction # 53210
Leg A
Leg A
Leg A
Leg B Leg B
Leg B

Page 3 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Tools Required for Assembly:
Power Driver W/Adjustable Torque
#2 Phillips Head Driver Bit
#2 Square Head Driver Bit
3/16" Hex Head Driver Bit or
Allen Wrench
Level
51708
3
53638
6
53176
7
53174
8
50072
10
Hardware Pack # 53209
Hardware is Drawn Actual Size
Instruction # 53210
1
52604

Back of
Motor Box
Detail A
1
4
3
All Screws
These Steps
Steps 1 & 2
3
Page 4 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Step 1: With the help of an assistant, lay the work-
surface(s) 1on a protected surface with the pilot holes
facing up. If your worksurface has a seam, lay the
joiner plate 2centered on the seam and about 3"
from the front. Attach it with (8) wood screws 3.
No pilot holes are provided. Do not over-tighten the
screws. Use a low torque setting on the power driver.
Step 2: Place all (3) leg assemblies 4on the
worksurface aligning the holes in the worksurface
supports with the pilot holes in the worksurface
1. See page 2 to determine the locations of Leg A
and Leg B. The motor boxes must face the inside
of the workstation. Do not allow the leg assemblies
to stand without support. They can tip over and the
gear housing could crack. Be
careful to not pinch the wires
between the motor boxes and
the worksurface 1. The
grommets on the motor wires
should be in the square notches
on the back of the motor boxes.
See Detail A. Attach the leg
assemblies to the worksurface
with (6) wood screws 3in
each. Leave the screws loose
by about 1/8". You need to
adjust the legs when installing
the wire management channel.
Instruction # 53210
ITEM # PART # DESCRIPTION QTY.
1 Varies Worksurface Varies
80035 3x5 Worksurface Joiner Plate 1
3 51708 M5 x 18mm (7/8") Sq/Ph/Wshr Head Wood Screw 49
4 Varies NewHeights Series 4 XT Leg Assembly 3
5 Varies NewHeights Series 4 XT Wire Management Channel
6 53638 5/16-18 x 3/8 Button Head Socket Screw 6
7 53176 . 5x.696x.58 Flat Washer 4
8 53174 1/4- 0x1/ Phillips Pan Head Machine Screw 4
9 53 5 TouchDown Hand Switch 1
10 5007 8 x 3/4 Pan Head Recex Drive Screw 4
11 50 86 NewHeights Control Box 1
1 5 604 3/16" Cable Clamp 4
13 PSSM-4- Power Strip 4 Recps USB Chargers 10 Ft Cord 1

Detail B
Step 3
3
B
5
6
Page 5 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Step 3: Your workstation may have two different
sizes of wire management channel 5. Determine
the correct locations of the channels according to
the length and width of the worksurface(s). Slide
apart the channel until the holes near the ends of
it align with the holes in the motor boxes on the
desk side of the workstation. Place the flat side of
the channel against the motor boxes. Insert (4)
socket screws 6through the holes near the ends of
the channel and thread them into the weld nuts inside
the motor boxes. See Detail B. Fully tighten. Fully
tighten the wood screws 3holding the desk side leg
assemblies to the worksurface 1. Attach the channel
to the worksurface with (5-10) wood screws 3through
the front flange of the channel. Fully tighten. Keep
the wood screws at the end of the slots.
Instruction # 53210

7
8
Cage Nuts Pre-
installed in Inner
Wire Management
Channel
Steps 4 & 5
C
Page 6 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Instruction # 53210
Step 4: Attach the other wire management channel 5
to the third leg 4on the return side of the table. See
Detail B on Page 5. Fully tighten all of the screws.
Fully tighten the(6) wood screws 3attaching the third
leg to the worksurface 1. Attach the wire management
channel to the worksurface with (4-10) wood screws 3.
Step 5: Place (2) black flat washers 7on (2) black
machine screws 8. Insert these through the slots in
one of the outer wire management sections and thread
them into the cage nuts pre-installed near the end of the
inner wire management section. See Detail C. Use any
(2) cage nuts that are accessible. Fully tighten. Repeat
Step 5 with the remaining wire management channel.
Detail C

lengths permitting. Capture the switch wire in the cable clamp 12 and attach it in the
location shown with (1) wood screw 3. No pilot hole is provided.
Step 7: Attach the power strip 13 at the suggested location shown. It can be installed
anywhere. Attach it with the screws that came with the power strip.
10
9
1
3
11
10
13
Steps 6 & 7
Page 7 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Instruction # 53210
Step 6: Align the holes in the control box 11 with the
pilot holes in the worksurface 1. Attach it with (2)
recex screws 10 . Align the holes in the switch 9with
the pilot holes in the worksurface. Attach it with (2)
recex drive screws 10 . The switch and control box
can be installed anywhere on the worksurface, wire

Switch
Wire
Motor
Wire
Power
Cord
Power
Strip
Power
Cord
Control
Box
Motor
Wire
Motor
Wire
Step 10: With the help of an assistant, set the work-
station upright in its final location. Level the unit if
required by turning the leveling glides clockwise
(from the top) on the low corners of the workstation.
If your workstation has casters, level it by turning
the bolts at the top of the casters.
Leveling Glide
HS
Hand
Switch
Center
Column
11
Page 8 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
M1 M2 M3
Right
Hand
Column
Step 8: Run the wires as shown in the wire runs diagram
below. Run the wires in the wire management channels
5. Plug the wire from the switch into the receptacle
labeled HS on the control box 11 . Plug the motor wires
into the cables and plug the other ends of the cables into
into the receptacles labeled M1, M2, and M3 as shown in
the wiring diagram at left. Place the excess cable inside
the channels.
Step 9: If your workstation will get an optional cross
support(s), plug the unit into a standard 110 volt
receptacle. Push the down arrow until the worksurface
reaches its lowest point and clicks. Push the up arrow
and raise the legs about 12". Install the cross support(s)
using the supplemental instructions that came with the
cross support package(s). Return the legs to the lowest
position and unplug the power.
Instruction # 53210
Left
Hand
Column

Page 9 OF 9
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Instruction # 53210
Operation and Reset Procedure
Plug the power cord into a standard 110v receptacle. A power surge protector is
recommended. Press the down arrow button until the worksurface reaches its lowest
position and clicks. The NewHeights™ workstation is ready for use. If you unplug or
lose power and the unit does not operate, follow the reset procedure below.
Reset Procedure: Unplug the power for 30 seconds and plug back in. Hold the down
arrow button until the unit stops at the bottom. Release the button; then hold the down
arrow button until the unit clicks twice.
Troubleshooting: If you are having any problems with the table operation, contact
RightAngle™ service at 800-298-4351 or [e-mail].
Warranty Information: NewHeights™ products are warranted to be free of defects
due to manufacturing or materials as follows: Three years on the gear and/or motor(s)
including the control box and switch. Five years on the support brackets, aluminum
columns and feet. We will replace any defective part after inspection by an
authorized agent. Costs incurred due to product replacement such as installation
labor or transportation are not covered by this warranty. When corresponding with
RightAngle™ products, record and provide the model and serial numbers located
on the control box.