RIGHT ANGLE 310CPU User manual

THREAD (2) WELD NUTS
PAGE 1 OF 2
5
VERSION DATED: 3/28/12
ONTO THE SOCKET SCREWS 6
TAPE MEASURE
AT THE HEIGHT
ALLEN WRENCH
YOU WANT THE BOTTOM OF YOUR CPU. FULLY TIGHTEN THE SOCKETSCREWS
7/32" HE HEAD DRIVER BIT OR
CORDLESS DRILL
.
TOOLS REQUIRED FOR ASSEMBLY:
FROM THE
BACK. THE PROJECTIONS ON THE WELD NUTS MUST FACE THE BACK OF
ASSEMBLY B. SEE DETAIL A.
STEP 4:
STEPS 1-4
SLIDE THE ASSEMBLY YOU JUST MADE INTO THE SLOT IN THE COLUMN
FROM THE TOP DOWN. ORIENT THE WELD NUTS 5 AS SHOWN IN DETAIL A
INSTRUCTION # 52611
WITH THE WIDE SIDES FACING EACH OTHER. THIS WILL MAKE THE WELD NUTS
LESS VISIBLE. THE NON-SKID PAD ON THE SUPPORT 2
6
SHOULD BE FACING UP
AS SHOWN IN
ARDWARE PACK # 51907
STEPS 1-4. SET THE CPU HOLDER ASSEMBLY B 1
310CPU OLDER INSTALLATION INSTRUCTIONS:
STEP 1: MEASURE THE HEIGHT OF YOUR CPU AND DETERMINE THE HEIGHT
AT WHICH YOU WANT THE BOTTOM OF YOUR CPU.
STEP 2: RAISE THE WORKSTATION TO ITS HIGHEST POSITION. RAISE THE COLUMN
COVER 4 AS HIGH AS IT WILL GO. PLACE (2) STAR WASHERS 7 ON (2) SOCKET
SCREWS 6 . INSERT THESE THROUGH THE HOLES IN THE BRACKET OF THE CPU
HOLDER ASSEMBLY B 1 .
STEP 3:
ITEM # PART # DESCRIPTION QTY.
1 800166 310CPU HOLDER ASSY B 1
2 800224 310CPU HOLDER SUPPORT BRACKET 2
3 800165 310CPU HOLDER ASSY A 1
4 800410 NewHeights COLUMN COVER (E ISTING) 1
5 52389 3/8-16 x 1/2 OFFSET WELD NUT 4
6 52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW 4
7 52477 3/8 INTERIOR TOOTH STAR WASHER 4
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
6
NOT SHOWN FOR CLARITY
DETAIL A
COLUMN COVER
REST OF WORKSTATION
READ ALL T E INSTRUCTIONS
BEFORE BEGINNING
1
2
4
7
OUTER COLUMN;
NON-SKID PAD
FACES UP
A
5PROJECTIONS FACE OUT

PAGE 2 OF 2
REVERSE THE LOCATIONS OF ASSEMBLY A & ASSEMBLY B.
ON THE TOP OF THE COLUMN.
STEPS 5-9
TO INSTALL THE CPU HOLDER ON THE OPPOSITE SIDE OF THE WORKSTATION,
STEP 5: PLACE YOUR CPU ONTO THE BOTTOM SUPPORT 2 . SLIDE THE BOTTOM
SUPPORT IN AGAINST THE SIDE OF THE CPU.
STEP 6: REPEAT STEPS 2 & 3 USING THE 310CPU HOLDER ASSEMBLY A 3 .
STEP 7: SLIDE THIS ASSEMBLY INTO THE SLOT IN THE COLUMN WITH THE SUPPORT 2
FACING DOWN (OPPOSITE THE BOTTOM SUPPORT). LET THE SUPPORT REST
ON THE TOP OF THE CPU.
STEP 8: SLIDE THE TOP SUPPORT 2 IN AGAINST THE SIDE OF THE CPU. HOLD
DOWNWARD PRESSURE ON ASSEMBLY A 3 AND TIGHTEN THE SOCKETSCREWS 6 .
STEP 9: REPLACE THE COLUMN COVER 4
THE DIFFERENCE BETWEEN
ASSEMBLY A AND ASSEMBLY B
IS THE LOCATION OF THE
SQUARE TUBE ON THE BRACKET
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 3/28/12
K&A MANUFACTURING
6
3
2
2
1
5
7
4
ASSEMBLY A 3
ASSEMBLY B 1