RIGHT ANGLE NewHeights Presidente User manual

Instruction #54261 • Dated: 04/5/2019
NewHeights™ Presidente Executive 3-Leg
Assembly Instructions
Warranty: raproducts.com/warranty
1 of 15
Assembly Video: https://youtu.be/AzcN2S43ub0

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 2 of 15
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
USE THIS PRODUCT ONLY AS INSTRUCTED.
FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS
MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.
Basic Safety Instructions
1. Intended Use. This Product is exclusively designed for use as indoor ofce furniture in compliance with all instructions and safety warnings
in the user manual. Any different use, or use extending beyond the intended use, may result in property damage or bodily injury and is pro-
hibited. This Product should not be used, operated or maintained with additional components not authorized by RightAngle Products.
BY USING THIS PRODUCT OR ANY FEATURE OF THIS PRODUCT, YOU AGREE TO COMPLY WITH ALL PRODUCT TERMS AND POL-
ICIES, INCLUDING WITHOUT LIMITATION ANY SAFETY WARNINGS AND INSTRUCTIONS, PROVIDED BY RIGHTANGLE PRODUCTS
AND ITS AFFILIATES. RIGHTANGLE PRODUCTS SHALL ASSUME NO LIABILITY FOR ANY DAMAGE OR INJURY CAUSED BY USE OF
THE PRODUCT A) IN VIOLATION OF ANY SAFETY WARNINGS OR INSTRUCTIONS; B) NOT AUTHORIZED BY RIGHTANGLE PROD-
UCTS; OR C) BY EVENTS BEYOND RIGHTANGLE PRODUCT’S CONTROL.
DO NOT SIT, STAND OR CRAWL ON OR UNDER THE PRODUCT.
MAKE SURE NO OBSTACLES ARE IN THE PRODUCT’S PATH.
MAKE SURE ALL CORDS ARE LONG ENOUGH TO ACCOMMODATE ANY CHANGE IN HEIGHT.
DO NOT USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.
2. Electrical Height Adjustment. The height of this Product may be adjusted electronically. Contact with electrical voltage may cause serious
injury and death. Only use the Product in compliance with these instructions. This Product should not be used in environments with high
levels of humidity or moisture.
KEEP CORDS AND ELECTRICAL COMPONENTS AWAY FROM HEAT AND LIQUIDS.
DO NOT OPEN ANY OF THE COMPONENTS: LEGS, CONTROL BOX, OR KEYPAD.
DO NOT USE WITH A DAMAGED PLUG OR CORD.
DO NOT INSERT ANYTHING INTO ANY SEAM OR OPENING.
3. Setup and Use. This Product should only be used and operated in good condition. When in use, no one should sit, stand or crawl on or
under the Product. There is a danger of crushing, shearing, injury or damage. Keep the entire range of motion of the Product clear of all
obstacles. Devices and object on the Product can tip over, fall or be crushed by the Product.
KEEP HANDS AND FINGERS CLEAR.
KEEP ALL OBSTACLES CLEAR OF THE PRODUCT’S PATH.
4. Users. This Product is not intended for use with children, individuals with restricted physical, sensory or mental capabilities, or individuals
who lack experience or knowledge, unless they are supervised by a person who is responsible for their safety or they have received instruc-
tions from a person who is responsible for their safety concerning how the Product must be used. Children should be closely supervised to
ensure that they do not play with the Product and its height adjustment mechanism to avoid risk of physical injury or
electric shock.
KEEP CHILDREN AWAY FROM THE PRODUCT, ITS CONTROL UNITS, AND KEYPADS.
WARNING
DANGER

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 3 of 15
G. 3/8-16 x 1” Black Adjustable Glide x4
H. SlimFix Bolt for 5mm Hole Zinc x24
I. Peel and Stick Screw Cover Caps Black x8
J. 10 X 5/8” Round Washer Head Drive Screw x64
K. 8 x 3/4” Pan Head Recex Drive Screw x4
L. Cable Clamp 3/16 Black x2
M. Grommet Insert x4
Tools Required for Assembly
A. Power Driver with Adjustable Torque
B. #2 Phillips Head Driver Bit
C. #2 Square Head Drive Bit
D. 3/16” Hex Head Driver Bit or Allen Wrench
E. 3/16” Allen Wrench
F. Phillips Screwdriver
Hardware Included for Assembly (may have extra)
Parts
N. Three Motor Control Box
Including GyroSense x1
O1. Two Button Up/Down Switch x1
O2. Four Button Programmable Up/Down Switch x1
Optional - If you have a programmable
switch, please refer to the installation
instructions included with the switch.
P. U-Channel x2
Q. Front Brackets x2
R. 3” x 5” plate x2
A B C
DE
G H I J
K L M
N O1 O2
P Q
F
R
Assembly Requires Two People

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 4 of 15
Step 1
Step 2
Back Panel
(Inside)
Kick Panel
(Inside)
x4
x4
H
H
A H
A
G H
Left Side Panel Right Side Panel
x8
Install levelers Install levelers
H
G
H
G
Q
Q Q
B
B

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 5 of 15
Note: Use Upper
Most Pilot Hole
x8
Step 3
Step 4
JA
JJ
Left Side
Panel
Back Panel
Right Side
Panel
• Tighten cams to
join side panels to
back panel.
C

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 6 of 15
• Slide the weld nuts on the side brackets into
the grooves at the front of the columns.
Step 5
Step 6
• Drive the wood screws into
the pilot holes. Then tighten
the machine screws. Left hand
shown. Right hand same.
J
J
A C
E

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 7 of 15
Back Panel
Kick
Panel
• Tighten camlocks through holes
in kick panel. Reversed direction.
Counter Clockwise = Tighten
Clockwise = Loosen
Step 7
I
M
I M
Step 8
• Slide the cross braces between
the back panel and kick panel
under the slim x bolts.
• Raise up and engage the
bolts into the cams. Tighten
the camlocks.
F

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 8 of 15
Step 9
• Install switch, u-channel plates, and control box on
the bottom of the worksurface.
• Note: Install modesty panel (optional). Refer to
modesty panel instruction #53901.
A C J K LB
JKNKJ
LP
K
OR
J J
• Assemble the return worksurface to the
short foot leg.
Step 10
J
A
J
CB
Note: refer to modesty panel instruction #53901
Table will NOT operate unless the
control box is screwed tight into
the table without any play.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 9 of 15
Step 11
Switch
Cable
Motor
Cable
Wiring Diagram Motor
Cable
Power Cord
Motor
Cable
Switch
Input
Motor
Input
Motor
Input
Power
Cord
Control Box
End View
Motor
Input
• Just run the cables into the control box. They
will get connected into the legs after Step 13.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 10 of 15
• Set the main worksurface onto the
main base.
• Attach each side with two screws
as shown.
• After the unit is raised, put in all
the leg support screws.
Step 12
Step 13
J
• Attach the small worksurface to
the main base with eight screws
through plates T.
• Connect the cables into the legs
as shown on Step 11.
R
A
J
CB
A
J
CB
J

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 11 of 15
• Attach the second u-channel
to the worksurface using the
screws as shown.
Step 14
J
Step 15
• Follow the start-up procedure
on page 14. Then raise the
table up using the switch.
• Attach the remaining screws
from the leg supports into
the worksurafce.
A
J
J
CB
A
J
CB

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 12 of 15
• Install divider cover and
worksurface grommet insert.
Note: return worksurface
NOT shown for assembly
clarication.
Step 16
Step 17
• Lower table to lowest
position to reset.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 13 of 15
Save for Reference
Standard Switch
Start Up Procedure:
• Plug the power cord into a standard 110V receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position.
• The workstation is ready for use.
• If the table is not functioning normally or has lost power, perform the reset procedure.
Reset Procedure:
• Unplug the unit from the wall for 10 seconds.
• Clear all obstructions from the travel path of the desk.
• Plug the unit back in the wall.
• Press and hold the down arrow key until the table reaches its lowest position.
Add Container Stops:
• Move the table to the upper or lower desired height.
• Rapidly press 4 times. You will hear a musical tone.
• Rapidly press 2 times. A musical tone plays two times.
- To add the upper container stop press A musical tone plays two times.
- To add the lower container stop press A musical tone plays two times.
Remove Container Stops:
• Move the table to the upper or lower preset height.
• Rapidly press 4 times. You will hear a musical tone.
• Rapidly press 2 times. A musical tone plays two times.
- To delete the upper container stop press You will hear a musical tone.
- To delete the lower container stop press You will hear a musical tone.
Troubleshooting:
If you are having any problems with the operation, contact RightAngle Products at 800.298.4351
or [e-mail]
If the leg assemblies are at uneven heights, it is usually caused by an improperly installed hex rod. Disassemble one
of the leg assemblies from the worksurface and make sure both ends of the hex rod are properly engaged in the hex
drives near the top of the leg assemblies.
Note

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 14 of 15
Start Up Procedure:
• Plug the power cord into a standard 110V receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position.
• The workstation is ready for use.
• If the table is not functioning normally, or has lost power,
perform the reset procedure.
Reset Procedure:
• Unplug the unit from the wall for 10 seconds.
• Clear all obstructions from the travel path of the desk.
• Plug the unit back in the wall.
• Press and hold the down arrow key until the table reaches its lowest position
See Packaged Instructions for Programmable Options
Optional Programmable Switch (full instructions packaged with switch)

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 15 of 15
If the table is unresponsive, uneven, or not functioning properly, perform a manual reset.
User settings are not reset in this process.
There are three methods to reset a workstation:
Reset Method A
1. Clear all obstructions from the travel path of the workstation
2. Disconnect the power to the control box for 30 seconds.
3. Reconnect the power
4. Press and hold the until the workstation has reached its lowest possible position.
Reset Method B (4 button programmable switch required)
1. Clear all obstructions from the travel path of the workstation
2. Quickly press UP + UP + UP + UP to enter the menu mode.
3. P01 is displayed and you will hear a musical tone.
4. Press the to navigate the menu.
5. Navigate to the P09 display
6. Press the button to enter or accept
7. Press and hold the until the workstation has reached its lowest possible position.
The workstation is now ready to operate
Reset Method C - 2 Button Switch
1. Clear all obstructions from the travel path of the workstation
2. Quickly press UP + UP + UP + UP to enter the menu mode.
3. You will hear a musical tone.
4. Press UP + UP + UP +
5. You will reach the limit adjustment menu and hear four musical tones.
6. Press and hold the until the workstation has reached its lowest possible position.
The reference is re-calibrated, the table should be leveled and the height indication should be correct.
Mechanical Reset Mode