RIGHT ANGLE HSAP User manual

PLACE THE HOOK AND SLOT ADAPTER PLATE
STEP 1:
TOOLS REQUIRED FOR ASSEMBLY:
INSTRUCTION # 50581
ARTICULATING ARM
3
CORDLESS DRILL
ALIGN THE HOLES IN THE HSAP WITH THE HOLES IN THE ARM. INSERT (6)
WITH THE HOOKS FACING UP AND TOWARD THE BACK.
#2 PHILLIPS DRIVER BIT
STEP 2:
(6) FLANGE LOCK NUTS
11/32 WRENCH OR SOCKET
VERSION DATED: 7/27/11
1 ON TOP OF THE
THROUGH THE HOLES IN THE HSAP AND ARM. THREAD
HOO AND SLOT ADAPTER PLATE INSTALLATION INSTRUCTIONS:
MACHINE SCREWS
2
2
PAGE 1 OF 2
4
REMOVE THE OLD KEYBOARD TRAY FROM THE ARTICULATING ARM
HARDWARE PAC # 50520 & 50525
AND TIGHTEN.
ONTO THE MACHINE SCREWS FROM THE BOTTOM
.
ITEM # PART # DESCRIPTION QTY.
1 HSAP HOOK AND SLOT ADAPTER PLATE 1
2 VARIES ARTICULATING ARM 1
3 50318 8-32 x 3/8 PHILLIPS TRUSS HEAD MACHINE SCREW 6
4 50267 8-32 SERRATED FLANGE LOCK NUT 6
5 MRD MYRIAD KEYBOARD TRAY 1
6 MMT MYRIAD MOUSE TRAY 1
7 52490 M6 EXTERNAL TOOTH LOCK WASHER 1
8 50016 1/4-20 KNURLED HEAD THUMB SCREW 1
9 50363 WIRE SADDLE LOCKING TOP 2
2
1
3
STEP 2
4
READ ALL THE INSTRUCTIONS BEFORE BEGINNING
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING

EYBOARD TRAY POSITION OPTIONS
PAGE 2 OF 2
BACK RIGHT
MOUSE TRAY POSITION OPTIONS
POSITION SHOWN
STEP 3: CHOOSE (1) OF (3) KEYBOARD TRAY 5 POSITIONS AVAILABLE AS SHOWN ON THE BOTTOM VIEW BELOW.
INSERT THE HOOKS ON THE TOP OF THE ARTICULATING ARM 2 INTO THE SET OF SLOTS CORRESPONDING TO THE
POSITION YOU DESIRE. WHEN THE TRAY BOTTOMS OUT, PULL IT FORWARD AS FAR AS IT WILL GO. THE HOLE AT
THE FRONT OF THE HSAP SHOULD ALIGN WITH ONE OF THE INSERTS IN THE BOTTOM OF THE TRAY. PLACE (1)
LOCK WASHER 7 ON THE THUMB SCREW 8 . THREAD THE THUMB SCREW THROUGH THE HOLE AT THE FRONT
OF THE HSAP AND INTO THE INSERT AND FULLY TIGHTEN.
STEP 4: SNAP (2) WIRE SADDLES 9 INTO THE (2) HOLES AT THE BACK OF THE TRAY 5 .
STEP 5: CHOOSE (1) OF (4) MOUSE TRAY P0SITIONS AVAILABLE AS SHOWN ON THE BOTTOM VIEW OF THE
KEYBOARD TRAY 5 BELOW. THERE ARE (2) RIGHT HAND OPTIONS AND (2) LEFT HAND OPTIONS. INSERT THE
SQUARE PEGS ON THE SIDE OF THE MOUSE TRAY 6 INTO THE SQUARE HOLES ON THE KEYBOARD TRAY
CORRESPONDING TO THE POSITION YOU DESIRE. SLIDE THE PEGS IN UNTIL THE BUTTONS SNAP, LOCKING THE
MOUSE TRAY IN PLACE. THE KEYBOARD AND MOUSE TRAY POSITIONS MAY BE CHANGED AT ANY TIME.
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 7/27/11
K&A MANUFACTURING
CENTERED POSITION
FAR LEFT POSITION
FAR RIGHT POSITION
4
FRONT
BACK LEFT POSITION
FORWARD RIGHT
4
STEP 5
POSITION
FORWARD LEFT POSITION
6
FRONT
8
9
5
STEPS 3 & 4
6
7