RIGHT ANGLE R-STYLE WORKSTATION 50643 User manual

3
LEVEL
.
POST LEG
PAGE 1 OF 2
FASTEN WITH (2) WOOD SCREWS
LAY THE WORKSURFACE ON A PROTECTED SURFACE WITH THE
THAT WILL BUTT ANOTHER WORKSTATION. CENTER THE THE JOINER PLATE ON
5
THE EDGE OF THE WORKSURFACE 1/2" FROM THE FRONT AND BACK EDGES.
ATTACH (2) JOINER PLATES
CORDLESS DRILL
TAPE MEASURE
STEP 3: 8
HARDWARE PACK # 50643 & 50648
INTO THE PILOT HOLES ON THE WORKSURFACE. DO NOT OVER TIGHTEN THE
ON EACH EDGE OF THE WORKSTATION(S)
SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
TO THE WORKSURFACE USING (3) OR (4) WOOD SCREWS
IN EACH JOINER PLATE.
2 5
. ATTACH THE TOP EDGE OF THE
MODESTY PANEL
WITH THE PILOT HOLES AT THE BACK CORNER OF THE WORKSUR
TOOLS REQUIRED FOR ASSEMBLY:
I STRUCTIO # 50583
9
BEFORE BEGI I G
PILOT HOLES FACING UP. ALIGN THE HOLES IN THE PLATE AT THE TOP OF THE
I STRUCTIO S
READ ALL THE
STEP 4:
5
FACE. ATTACH THE POST LEG WITH (4) WOOD SCREWS
VERSIO DATED: 9/14/11
#2 PHILLIPS HEAD DRIVER BIT
R-STYLE™ WORKSTATIO ASSEMBLY I STRUCTIO S:
STEP 1: LAY THE WORKSURFACE ON A PROTECTED SURFACE WITH THE
INSERTS AND PILOT HOLES FACING UP. ASSEMBLE THE RIGHT LEG ASSEMBLY
3 ,
THE MODESTY PANEL 2 , AND THE LEFT LEG ASSEMBLY 1 USING (3) MACHINE
SCREWS 4 IN EACH LEG ASSEMBLY. DO NOT FULLY TIGHTEN THE SCREWS. IF
YOUR WORKSTATION HAS THE OPTIONAL WIRE MANAGEMENT CHANNEL,
INSTALL IT ACCORDING TO THE INSTRUCTIONS THAT CAME WITH THE CHANNEL.
STEP 2: PLACE THE LEG AND MODESTY PANEL ASSEMBLY ON THE WORKSUR
FACE 7 ALIGNING THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE
INSERTS IN THE WORKSURFACE. ATTACH IT USING (2 OR 3) MACHINE SCREWS
6
ON EACH WORKSURFACE SUPPORT. FULLY TIGHTEN ALL THE FASTENERS
INCLUDING THE SCREWS HOLDING THE MODESTY PANEL 2 TO THE LEFT LEG
ASSEMBLY 1 AND THE RIGHT LEG ASSEMBLY
ITEM # PART # DESCRIPTION QTY.
1 VARIES R STYLE™ LEFT LEG ASSEMBLY VARIES
2 VARIES R STYLE™ MODESTY PANEL VARIES
3 VARIES R STYLE™ RIGHT LEG ASSEMBLY VARIES
4 R STYLE A 6 x 15mm MACHINE SCREW VARIES
5 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW VARIES
6 50133 10 32 x 1/2 PHILLIPS TRUSS HEAD MACHINE SCREW VARIES
7 800512 2 X 2 WORKSURFACE JOINER PLATE VARIES
8 29SL 29SL POST LEG VARIES
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
5
5
WORKSTATION SIZES AND
CONFIGURATIONS WILL VARY.
ASSEMBLY STEPS ARE THE SAME.
STEPS 1-3
WORKSURFACE SUPPORT
3
1
2
4
6
7
LEFT & RIGHT R-STYLE™ WORKSTATIO (S)
9
COR ER WORKSTATIO
5
STEP 4

PAGE 2 OF 2
IF NECESSARY.
, (2) IN EACH JOINER PLATE. LEVEL THE WORKSTATION
STEP 5: LAY THE WORKSURFACE ON A PROTECTED SURFACE WITH THE PILOT HOLES FACING UP. ALIGN
THE HOLES IN THE PLATES AT THE TOPS OF THE POST LEGS 9 WITH THE PILOT HOLES IN THE WORKSURFACE.
ATTACH THE POST LEGS USING (4) WOOD SCREWS 5 IN EACH LEG.
STEP 6: WITH THE HELP OF AN ASSISTANT, SET THE LEFT HAND WORKSTATION UPRIGHT IN ITS FINAL LOCATION.
LEVEL IT IF NECESSARY BY TURNING THE GLIDES OUT (CLOCKWISE FROM THE TOP) ON THE LOW SIDES OF THE
UNIT. SET THE EDGE OF THE CORNER WORKSTATION ON THE JOINER PLATES ON THE RIGHT HAND EDGE OF
THE LEFT HAND WORKSTATION. MAKE SURE THE EDGES OF THE WORKSURFACES ARE FLUSH, ATTACH THEM
TOGETHER WITH (4) WOOD SCREWS 5 , (2) IN EACH JOINER PLATE.
STEP 7: SLIDE THE JOINER PLATES ON THE RIGHT HAND WORKSTATION UNDER THE RIGHT HAND EDGE OF
THE CORNER WORKSURFACE. MAKE SURE THE EDGES OF THE WORKSURFACES ARE FLUSH. ATTACH THEM
TOGETHER WITH (4) WOOD SCREWS 5 , (2) IN EACH JOINER PLATE. LEVEL THE RIGHT HAND WORKSTATION
IF NECESSARY.
STEP 8: PLACE THE EDGE OF THE WORKSURFACE ON THE PENNINSULA WORKSTATION OVER THE JOINER
PLATES ON THE RIGHT HAND WORKSTATION. MAKE SURE THE EDGES OF THE WORKSURFACES ARE FLUSH.
ATTACH THEM TOGETHER WITH (4) WOOD SCREWS 5
TYPICAL U SHAPED CONFIGURATION IS SHOWN
AS AN EXAMPLE ONLY. YOUR WORKSTATION'S
CONFIGURATION MAY BE DIFFERENT.
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 9/14/11
K&A MANUFACTURING
STEP 5
PE I SULA WORKSTATIO
5
R STYLE LEG ASSEMBLY.
THIS POST LEG MAY BE REPLACED WITH AN
ON SOME WORKSTATION CONFIGURATIONS,
9
CORNER
THE CORNER WORKSTATION
THE SHORT FEET GO TOWARD
WORKSTATION
WORKSTATION
PENNINSULA
THE LEG ASSEMBLIES WITH
5
STEPS 6-8
LEFT HAND
R STYLE™
WORKSTATION
RIGHT HAND
R STYLE™
WORKSTATION