RIGHT ANGLE R-STYLE 36USL User manual

NOTE: COMPONENTS SHOWN ARE FOR A 36" UPPER SHELF.
HARDWARE PACK # 51914 BLACK, 51982 SILVER
CAMS
ASSEMBLY INSTRUCTIONS ARE THE SAME FOR A 48" OR 60" SHELF.
PAGE 1 OF 2
BACK
2
READ ALL THE INSTRUCTIONS
5
4) INTO THE 60" BACK PANEL
VERSION DATED: 8/21/12
USING A PHILLIPS SCREWDRIVER, MAKE SURE THAT ALL OF THE
AND THE RIGHT END PANEL
5
1
3) INTO THE 36" OR 48" BACK PANEL
OR 12) SLIM FIX BOLTS
USING A CORDLESS DRILL AND PHILLIPS DRIVER BIT, SCREW 11)
R-STYLE 6USL, 48USL, & 60USL UPPER SHELF ASSEMBLY INSTRUCTIONS:
PHILLIPS SCREWDRIVER
4) EACH INTO THE LEFT END PANEL
#2 PHILLLIPS HEAD DRIVER BIT
4
CORDLESS DRILL
STEP 1:
TOOLS REQUIRED FOR ASSEMBLY:
STEP 2:
TORQUE SETTING ON THE DRILL.
ARE IN THE OPEN POSITION FULLY COUNTER-CLOCKWISE).
INSTRUCTION # 50641
4)4)
LEFT END RIGHT END
SHOWN BELOW LEFT: DO NOT OVER-TIGHTEN THE BOLTS. USE A LOW
INTO THE PRE-DRILLED HOLES IN THE PANELS
STEPS 1 & 2
BEFORE BEGINNING
ITEM # PART # DESCRIPTION QTY.
1 51687 5mm SLIM FIX BOLT 11 OR 12
2 52064 11mm ZINC CAM 11 OR 12
3 10152 BOOKSHELF LEFT END ASSY 1
4 10153 BOOKSHELF RIGHT END ASSY 1
5 VARIES BOOKSHELF BACK 36", 48", OR 60" 1
6 VARIES BOOKSHELF SHELF 36", 48", OR 60" 1
7 800150 BOOKSHELF TABLE ANGLE BRACKET 1 OR 2
8 50133 10-32 x 1/2 PHILLIPS TRUSS HEAD MACHINE SCREW 2 OR 4
9 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 2 OR 4
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
4
3
SCREWDRIVEER
PHILLIPS
CLOCKWISE
CAM OPERATION
TIGHTEN CLOCKWISE
LOOSEN COUNTER-
HARDWARE
1
2PRE-INSTALLED)
SHELF
5
3) 36" & 48" 4) 60"

3
STEP 4 & 5
6
5
STEP
1
2
WORKSURFACE
8
7
9
STEP 6 & 7
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
VERSION DATED: 8/21/12
K&A MANUFACTURING
PAGE 2 OF 2
STEP : LAY THE BACK PANEL ASSEMBLY 5 ON A PROTECTED SURFACE WITH THE SLIM FIX BOLTS 1 FACING
UP. INSERT THE SLIM FIX BOLTS ON THE BACK PANEL ASSEMBLY INTO THE CAMS
2 ON THE BACK EDGE OF THE
SHELF ASSEMBLY 6 . TIGHTEN THE CAMS CLOCKWISE).
IMPORTANT NOTE: WHEN TIGHTENING THE CAMS, THEY WILL STOP AT A DETENT IN THE MECHANISM BEFORE
THEY ARE FULLY TIGHTENED. BE SURE TO TIGHTEN THEM PAST THE DETENT.
STEP 4: LAY THE LEFT END ASSSEMBLY ON A PROTECTED SURFACE WITH THE SLIM FIX BOLTS 1 FACING UP.
INSERT THE SLIM FIX BOLTS ON THE END PANEL INTO THE CAMS
2 ON THE BACK AND SHELF ASSEMBLY. FULLY
TIGHTEN THE CAMS CLOCKWISE).
STEP 5: REPEAT STEP 4 WITH THE RIGHT END ASSEMBLY 4 .
STEP 6: PLACE THE UPPER SHELF ASSEMBLY ON THE WORKSURFACE FLUSH WITH THE BACK. ATTACH A BOOKSHELF
ANGLE BRACKET 7 TO ONE OF THE END ASSEMBLIES OR 4 . INSERT 2) MACHINE SCREWS 8 THROUGH THE
HOLES ON THE WIDE FLANGE OF THE BRACKET AND THREAD THEM INTO THE INSERTS PRE-INSTALLED IN THE PANEL.
FULLY TIGHTEN. ATTACH THE NARROW FLANGE OF THE BRACKET TO THE BOTTOM OF THE WORKSURFACE. INSERT
2) WOOD SCREWS 9 THROUGH THE HOLES AND THREAD THEM INTO THE WORKSURFACE. DO NOT OVER-
TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
STEP 7: IF Y0UR SHELF HAS 2) ANGLE BRACKETS 7 , REPEAT STEP 6 ON THE OPPOSITE END OF THE SHELF.