RIGHT ANGLE R-Style Romeo Flip User manual

Instruction #54274 • Dated: 06/23/2021 1 of 6
R-Style™Romeo Flip Assembly Instructions
Warranty: raproducts.com/warranty

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 2 of 6
E. 8mm x .625 Machine Screw x4
F. 8mm x .75 Thread Screw x12
G. Wood Screw x13
H. Caster Wrench x1
I. 5mm Allen Wrench x1
J. Caster Leveling Nut x4
K. Front Bumper x2
L. Clear Bumper x1
Tools Required for Assembly
A. Power Driver with Adjustable Torque
B. Tape Measure
C. #2 Square Head Drive Bit (Recommended)
D. #2 Phillips Head Driver Bit (Recommended)
A B DC
Hardware and Tools Included for Assembly (may have extra)
E F G
H I
J K L
M. Casters x4
N. Leg Assemblies x2
O. Main Beam x1
P. Hinge Mechanism x1
Q. Left Hinge x1
R. Right Hinge x1
Flip Table Parts
M
N
OPRQ

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 3 of 6
Step 1
• Screw all four leveling nuts onto the caster stems
using the caster wrench.
J
M
Step 2
• Screw the casters onto both leg assemblies.
N
HJ
M

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 4 of 6
NF
Step 3
• Lay the beam on a protective surface with the
insert channels facing up.
• Place one of the leg assemblies over the main
beam sliding the insert into the hollow leg
assembly. The leg assemblies are interchangeable.
• Insert the screws into the leg and fully tighten.
Do this to both legs.
Step 4
• Set the main beam and leg assembly upright.
• Peel the backing off two front bumpers and attach
them to the main beam. Locate them about 6-1/4”
from the ends of the beam and on center.
K
N
FI
O
K
N
O
K

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 5 of 6
Step 5
• Set the left and right hinges on the main
beam.
• Attach four screws through the hinges
and into the main beam.
Step 6
• Set the hinge mechanism onto the main
beam and attach with four machine screws.
• Peel the backing off the clear bumper and
attach it to the center of the mechanism.
F
A
P
R
O
Q
L
A C F
A C E
Detail A
E

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 6 of 6
Step 7
• Lay the worksurface onto a protected
surface with the pilot holes facing up.
• Unlock the mechanism until it locks into
place by pulling the handle.
• Attach the worksurface to the mechanism
and both hinges with wood screws.
Step 8
• With the help of an assistant, place the
assembled unit on its caster wheels.
G
A D G
Operation
• To ip the worksurface to a vertical position, pull out on the hinge mechanism handle, and rotate the worksurface
upward.
• Place the retainer into the slot on the body of the mechanism to secure it. Securing the worksurface with the
retainer in the vertical potion is critical for safety reasons.
• To place the worksurface in the horizontal position, pull the retainer out of the slot and rotate the worksurface
downward until the mechanism lock into place.
Get help lifting
heavy items.