Roger PR402DR User manual

Roger Access Control System
Installation guide for
PR402DR type access controllers
Firmware version: 1.18.6 or newer
Hardware version: 1.4
Document version: Rev. I
© 2016 ROGER sp. z o.o. sp.k. All rights reserved. This document is subject to the Terms of Use in their current version published at
the www.roger.pl website of the Roger sp. z o.o. sp.k. company (hereinafter referred to as ROGER).

PR402DR Installation Guide Rev.I.doc
2017-09-18
2/20
Contents
1. Introduction .................................................................................................................. 3
1.1 This manual ....................................................................................................................... 3
2. Description and Specification........................................................................................ 3
3. Installation .................................................................................................................... 5
3.1 Terminals and connection diagram ...................................................................................... 5
3.2 Front panel ........................................................................................................................ 9
3.2.1 PR402DR controller ....................................................................................................... 9
3.2.2 PR402DR-BRD controller ................................................................................................ 9
3.3 Power supply ................................................................................................................... 10
3.3.1 PR402DR and PR402DR-BRD controllers ....................................................................... 10
3.3.2 PR402DR-12VDC and PR402DR-12VDC-BRD controllers ................................................. 12
3.4 Connection of door lock .................................................................................................... 13
3.5 Communication with controller .......................................................................................... 14
3.6 Communication of controller with peripheral devices .......................................................... 14
3.6.1 PRT readers, XM expanders and HRT82FK panel (RACS CLK/DTA).................................. 14
3.6.2 PRT and third party readers (Wiegand and Magstripe) ................................................... 15
3.7 Input and output lines ...................................................................................................... 15
3.7.1 Inputs......................................................................................................................... 15
3.7.2 Relay outputs .............................................................................................................. 15
3.7.3 General purpose outputs.............................................................................................. 15
3.8 Installation guidelines....................................................................................................... 15
4. Configuration............................................................................................................... 16
4.1 Controller address ............................................................................................................ 16
4.1.1 Setting the address by means of jumpers ..................................................................... 16
4.1.2 Addressing during firmware update (Fixed ID) .............................................................. 17
4.1.3 Addressing during Memory Reset procedure.................................................................. 17
4.1.4 Addressing by means of PR Master software ................................................................. 17
4.2 Memory Reset procedure .................................................................................................. 17
4.2.1 Simplified Memory Reset procedure (firmware 1.18.6 or newer) ..................................... 18
4.2.2 Simplified Memory Reset procedure (firmware older than 1.18.6) ................................... 18
4.2.3 Full Memory Reset procedure ....................................................................................... 18
4.3 Controller programming.................................................................................................... 18
4.4 Firmware update .............................................................................................................. 19
5. Ordering information................................................................................................... 19
6. Product history ............................................................................................................ 20

PR402DR Installation Guide Rev.I.doc
2017-09-18
3/20
1. INTRODUCTION
1.1 This manual
This manual contains minimum information that is necessary to properly install devices and to
perform initial tests. Following documents which are available at www.roger.pl supplement this
manual:
Functional description of PRxx2 series controllers
PR Master User Manual
If PR402DR and PR402DR-12VDC controllers are not clearly distinguished in particular paragraph,
then information specified for PR402DR also applies to PR402DR-12VDC. Similarly if PR402DR-BRD
and PR402DR-BRD-12VDC controllers are not clearly distinguished in particular paragraph, then
information specified for PR402DR-BRD also applies to PR402DR-BRD-12VDC. Designation
PR402DR type controller applies to all versions of this controller.
2. DESCRIPTION AND SPECIFICATION
PR402DR type controller is single door access controller used in RACS 4 access control system. Both
PR402DR and PR402DR-BRD versions are functionally identical but differ mechanically. PR402DR is
installed inside plastic enclosure fitted to mounting on DIN 35 mm rail, while PR402DR-BRD is just a
PCB module without enclosure. Both controllers replace discontinued PR402-BRD, which is the
same as PR402DR and PR402DR-BRD in regard of their functions. Moreover, PR402DR-12VDC
controller is simplified version of PR402DR controller in regard of power supply capabilities. This
controller is also available in plastic enclosure adapted for mounting on DIN 35mm rail as well as
PCB module. The summary of all available PR402DR versions is given in table 1.
Table 1. Versions of PR402DR type controllers
Name
Installation
Power supply
PR402DR
Plastic enclosure adapted for
installation on DIN 35mm rail.
18VAC, 12VDC or 24VDC power supply. Backup
battery can be connected directly. The controller
offers 12VDC power supply outputs (AUX, TML).
PR402DR-
BRD
PCB module with mounting holes.
Additional attachments for
installation on DIN35mm rail are
included.
see PR402DR
PR402DR-
12VDC
see PR402DR
12VDC power supply. Backup battery cannot be
connected directly. The controller offers 12VDC
power supply outputs (AUX, TML).
PR402DR-
BRD-12VDC
see PR402DR-BRD
see PR402DR-12VDC
The new, factory-made controller has the address ID=00 and MASTER proximity card is included.
The card can be used for the initial tests after connection of external reader. PR402DR type
controllers are not equipped with built-in reader and they require connection of external reader(s)
operating in RACS CLK/DTA (PRT series terminals), Wiegand 26…66bit, Magstripe or other format.
Controllers can be configured with PR Master software installed on computer and they can be
connected to computer by means of communication interface e.g. UT-2USB, UT-4DR, RUD-1 or by
means of CPR32-NET network controller.
Note: PR402DR and PR402DR-BRD controllers require PR Master 4.4.2 or newer, while PR402DR-
12VDC and PR402DR-BRD-12VDC controllers require PR Master 4.5.6 or newer.

PR402DR Installation Guide Rev.I.doc
2017-09-18
4/20
Table 2. Specification
Supply voltage
Nominal 18VAC, min./max. range 17-22VAC (only PR402DR/PR402DR-BRD)
Nominal 12VDC, min./max. range 10-15VDC
Nominal 24VDC, min./max. range 22-26VDC (only PR402DR/PR402DR-BRD)
Backup battery
13.8V/7Ah, charging current app. 300mA (only PR402DR/PR402DR-BRD)
Average current
consumption
100 mA (excluding load points connected to AUX and/or TML outputs)
Inputs
Eight (IN1..IN8) NO/NC inputs, electrically biased to +12V via 15kΩ resistor,
triggering level app. 3.5V
Relay outputs
Two (REL1,REL2) relay outputs with single NO/NC contact, 30V/1.5A (REL1)
and 230VAC/5A (REL2)
Transistor outputs
Two (IO1,IO2) open collector outputs, 15VDC/1A
Power supply
outputs
Two power supply outputs: 12VDC/0.2A (TML) and 12VDC/1A (AUX)
Distances
Between controller and communication interface (RS485): max. 1200m
Between controller and PRT reader (RACS CLK/DTA): max. 150 m
Between controller and XM expander (RACS CLK/DTA): max. 150 m
Environmental class
(according to EN
50131-1)
Class I, indoor general conditions, temperature: +5°C to +40°C, relative
humidity: 10 to 95% (no condensation)
IP code
PR402DR: IP41
PR402DR-BRD: IP20
Dimensions HxWxD
PR402DR: 85 x 124 x 73mm
PR402DR-BRD: 80 x 115 x 28mm
Weight
PR402DR: approx. 200g
PR402DR-BRD: approx. 100g
Certificates
CE

PR402DR Installation Guide Rev.I.doc
2017-09-18
5/20
3. INSTALLATION
3.1 Terminals and connection diagram
Fig. 1 PR402DR controller
Table 3. PR402DR/PR402DR-12VDC terminals
Terminal
Description
Terminal
Description
IN8
IN8 input line
P1
Power supply for controller
IN7
IN7 input line
BAT-
Backup battery (disabled for
PR402DR-12VDC controller)
GND
Ground
BAT+
Backup battery (disabled for
PR402DR-12VDC controller)
IN6
IN6 input line
IO1
IO1 output line
IN5
IN5 input line
IO2
IO2 output line
GND
Ground
IN1
IN1 input line
B
RS485 communication bus
IN2
IN2 input line
A
RS485 communication bus
GND
Ground
GND
Ground
IN3
IN3 input line
DTA
RACS CLK/DTA comm. bus
IN4
IN4 input line
CLK
RACS CLK/DTA comm. bus
TML
Built-in feeder 12VDC/0.2A output
(recommended supply for readers)
NO1
REL1 relay output (NO)
AUX
Built-in feeder 12VDC/1A output
(power supply for general purposes)
NC1
REL1 relay output (NC)
NC2
REL2 relay output (NO)
COM1
REL1 relay common terminal
NO2
REL2 relay output (NC)
P2
Power supply for controller
COM2
REL2 relay common terminal

PR402DR Installation Guide Rev.I.doc
2017-09-18
6/20
Fig. 2 PR402DR-BRD controller
Table 4. PR402DR-BRD/PR402DR-BRD-12VDC terminals
Terminal
Description
Terminal
Description
BAT+
Backup battery (disabled for
PR402DR-BRD-12VDC controller)
GND
Ground
BAT-
Backup battery (disabled for
PR402DR-BRD-12VDC controller)
IN7
IN7 input line
P1
Power supply for controller
IN8
IN8 input line
P2
Power supply for controller
IO1
IO1 output line
COM
REL1 relay common terminal
IO2
IO2 output line
NC
REL1 relay output (NC)
IN1
IN1 input line
NO
REL1 relay output (NO)
IN2
IN2 input line
CLK
RACS CLK/DTA comm. bus
GND
Ground
DTA
RACS CLK/DTA comm. bus
IN3
IN3 input line
GND
Ground
IN4
IN4 input line
A
RS485 communication bus
TML
Built-in feeder output 12VDC/0.2A
(recommended supply for readers)
B
RS485 communication bus
AUX
Built-in feeder output 12VDC/1A
(power supply for general purpose)
GND
Ground
NC
REL2 relay output (NO)
IN5
IN5 input line
NO
REL2 relay output (NC)
IN6
IN6 input line
COM
REL2 relay common terminal

PR402DR Installation Guide Rev.I.doc
2017-09-18
7/20
Fig. 3 Typical connection diagram for PR402DR or PR402DR-BRD controller

PR402DR Installation Guide Rev.I.doc
2017-09-18
8/20
Fig. 4 Typical connection diagram for PR402DR-12VDC or PR402DR-BRD-12VDC controller

PR402DR Installation Guide Rev.I.doc
2017-09-18
9/20
3.2 Front panel
3.2.1 PR402DR controller
According to fig. 5, the PR402DR controller is equipped with LED indicators on front panel to
indicate various states of the device and with RESET button to restart the controller in the same
way as in case of powering device off and then on. The RESET button can also be used during
Memory Reset procedure and during firmware update procedure.
Table 5. PR402DR front panel
AC
AC supply
DC
DC supply
ARMED/DISARMED
Current arming mode
OPEN
Door unlocked
SYSTEM
Various signalling functions
LINK
Data transmission by means of RS485 bus
Fig. 5 PR402DR front panel
3.2.2 PR402DR-BRD controller
According to fig. 6, PR402DR-BRD is equipped with 5 LED indicators and RESET button (S1) on its
PCB. RESET button can be used to restart the controller in the same way as in case of powering
device off and then on. The RESET button can also be used during Memory Reset procedure and
during firmware update procedure.
Table 6. LED indicators of PR402DR-BRD controller
AC (D33)
AC supply
SYS (D24)
Various signalling functions
OPN (D19)
Door unlocked
STAT (D11)
Current arming mode
LINK (D2)
Data transmission on RS485 bus

PR402DR Installation Guide Rev.I.doc
2017-09-18
10/20
Fig. 6 LED indicators of PR402DR-BRD controller
3.3 Power supply
3.3.1 PR402DR and PR402DR-BRD controllers
Basically, PR402DR and PR402DR-BRD controllers are designed for power supply from
230VAC/18VAC transformer with minimal power output 25VA, but they can also be supplied with
12VDC or 24VDC. The connection of power supply is shown in fig. 7, fig.8 and fig. 9.
If controller is supplied with 18VAC or 24VDC, then 12V backup battery can be connected in order
to provide power supply in case of mains supply shortage. The controller charges backup battery
with 300mA stabilized current up to 13.8V. Backup power supply is activated automatically in case
of main powers supply shortage. If the voltage at backup battery drops below approx. 10V then the
battery is automatically disconnected from controller and remains disconnected until mains power
supply returns. Depending on charging phase of backup battery, the voltage at AUX and TML
terminals may vary in range of 11V (initial charging phase) to 13.8V (final charging phase) which is
not a symptom of failure but it results from applied concept of battery charging.
In case of 12VDC power supply, backup battery cannot be directly connected to controller and in
such case backup power supply must be provided by 12VDC power supply unit.
General guidelines for 18VAC power supply
GND terminals of controllers must be connected with any wire.
Controllers can operate with directly connected backup batteries.
Controllers cannot be started using only power supply from backup battery.