rollease acmeda Automate FT User manual

AUTOMATE | FT MOTOR INSTRUCTIONS
DESCRIPTION
AUTOMATE | FT MOTOR is a mulfuncon tubular motor oering three dierent modes of operaon;
• E-type for standard use,
• MANUAL FT Mode for use with convenonal locking devices with fabric tensioning,
• AUTO FT Mode for use with Rollease Acmeda’s proprietary ULTRA LOCK providing automac fabric
tensioning.
Acvang fabric tension (FT) mode delivers a choice of 3 disnct tensioning levels to suit a wide range of
sizes and external applicaons.
Funconal opons in each operang mode include; IMPACT DETECTION & FAVOURITE POSITION.
Impact detecon senses an obstacle in the blinds path and redirects the blind to protect the motor,
hardware and fabric, ensuring product longevity.
An intermediate seng allows for a customised favorite posion to be pre-set.
TECHNICAL SPECIFICATIONS
Rated Torque 15Nm
Fabric Tension Torque (Electronically Selectable 5Nm / 10Nm / 15Nm)
Rated speed 15rpm
RF receiver 433.92MHz
Protection class IP44
Rated Voltage 220 - 240V AC
Frequency 50Hz
Motor Weight 1.98Kg
Rated current 140W
Rated power 0.61A
Motor diameter 45mm
Max Running Time 4 min
INSTR.RB24-6001-069005_SEPT 2015 v1.0
BRAKELIMIT SWITCH EARB
MT R
ELECTRONIC
LIMIT SWITCH
BRAKE FABRIC
TENSION
IMPACT
DETECTION
ULTRA-LOCK FAVORITE
POSITION
FUNCTIONS
Page. 1 of 12
AUTOMATE | FT MOTOR [Ø45/15Nm/15rpm]
P/N: RB24-6005-069005

© 2015 Rollease Acmeda
CONTENTS
1. Compatible Controllers p2
2. Installation p3
2.1 WARNING: Important Safety instructions to be read before installations p3
2.2 Assembly p4
2.3 Wiring Diagram p4
3. Programming & Use p4
3.1 Warning: Important safety instructions to be read prior to operation p4
3.2 Overview of P2 function – How to activate setting mode p5
3.3 Overview of operational modes p5
3.4 Pairing motor to transmitter p6
3.5 Setting top & bottom limits p7
3.6 Set Favourite position p8
3.7 Impact Detection p9
3.8 Copy Channel from an existing primary transmitter p9
3.9 Activate / Deactivate Fabric Tension Mode p10
3.10 Switch between Auto & Manual Lock Mode p10
3.11 Adjusting Tension Level p10
4. Troubleshooting p11
COMPATIBLE CONTROLLERS
RF500sRF400sA.R.T | Wind & Light SensorsA.R.T | Motion Sensor
Page. 2 of 12

© 2015 Rollease Acmeda © 2015 Rollease Acmeda
2. INSTALLATION
2.1 WARNING: Important safety instrucons to be read before installaon.
Incorrect installaon can lead to serious injury and will void manufacturer’s liability and warranty.
• Installaon and programming to be performed by a suitably qualied installer.
• For use within tubular blinds & awnings.
• Ensure correct crown and drive adaptors are used for the intended system.
• Use only Rollease Acmeda hardware.
• Before installaon, remove any unnecessary cords and disable any equipment not needed for powered operaon.
• Ensure torque and operang me is compable with end applicaon.
• Do not expose the motor to water or install in humid or damp environments.
• Tube and the drive adaptor should be evenly xed with 4 pieces of 4x10 countersunk self-tapping screws. Ensure
screw p does not penetrate through the internal surface of the drive.
• Motor is to be installed in horizontal applicaon only.
• Do not drill into motor body.
• For awning installaon, a horizontal distance of at least 0,4m is to be maintained between the fully unrolled
driven part and any obstacle.
• Ensure at least one control point is located within direct sight of unit but away from any moving parts.
• The roung of cable through walls shall be protected by isolang bushes or grommets.
• Ensure power cable and aerial is clear and protected from moving parts.
• Power supply cables are not be exposed to sunlight and must be protected by U.V resistant conduit.
• Ensure power is isolated prior to connecng or disconnecng inline connector.
• If cable or inline connector is damaged do not use.
Page. 3 of 12

© 2015 Rollease Acmeda
2.3 WIRING
3.1 WARNING: Important safety instrucons to be read prior to operaon.
It is important for the safety of persons to follow these instrucons. Save these instrucons for future reference.
• Persons (including children) with reduced physical, sensory or mental capabilies, or lack of experience and knowledge
should not be allowed to use this product.
• Keep remote controls away from children.
• Frequently inspect for improper operaon. Do not use if repair or adjustment is necessary.
• Keep motor away from acid and alkali.
• Do not force the motor drive.
• Keep clear when in operaon.
• This unit has a thermal cut-o switch. The rated operang me is 4 minutes. Unit will restart once it cools down.
• Isolate power prior to unplugging connector, performing maintenance or window cleaning.
• Avoid operaon if frost or ice has formed on motorized unit.
Power o
1
2
3
AC
1
2
3
3×0.75mm² 240V/50Hz
220 - 240V/50Hz
according to product nameplate
1
2
3
Blue = Neutral
Brown = Direction
Green/Yellow = Earth
3. PROGRAMMING & USE
Use rivet or screw
to install drive adapter
2.2 ASSEMBLY
Please refer to Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used.
1. Install specified crown & drive adaptor for selected tube.
2. Ensure drive retainer clip is securely in place.
3. Measure distance from end of crown/tube to the centre of drive.
4. Insert motor into tube
NOTE:
• Use a file to ensure tube is free of burrs.
• Use 4 x rivets or screws to fix drive adaptor to tube.
• Ensure screw tips do not penetrate through the internal surface of drive
Page. 4 of 12
1
2
3

© 2015 Rollease Acmeda © 2015 Rollease Acmeda
3.2 OVERVIEW OF P2 FUNCTION
Page. 5 of 12
Single Channel / Timer Fieen Channel
P2 = zeroP2 = zero & CH (+)
Press P2
RF400sRF500s
Below is an overview of how to acvate the P2 funcon on your chosen primary controller.
3.3 OVERVIEW OF OPERATIONAL MODES
3 SELECTABLE MODES
TENSION
Top limit
Boom limit
MODE 1
E-Type
(DEFAULT)
MODE 2
FT MODE
Automac Lock
MODE 3
FT MODE
Manual Lock
END OF CYCLE
CYCLE PAUSE
LEGEND

© 2015 Rollease Acmeda
Page. 6 of 12
3.4 PAIRING MOTOR TO TRANSMITTER
Operation
Item Item Operation Result Illustration
Setup
bottom
limit
1
Keep pressing the
LIMIT key on the
primary transmitter for
6 seconds above
The motor sounds "KA
KA"
2 Release the key The motor is under the
status of Limit setting
3Press the DOWN key
on the transmitter The motor runs down
4
When the motor is
running close to the
end-point of lower limit,
press STOP
The motor stops running
5Press either UP or
DOWN key
The motor runs step by
step to adjust lower limit
accurately
6Press CONFIRM key
on the transmitter
The motor sounds "KA
KA", the setting has
complete.
Setup
upper limit
7Press UP key on
primary transmitter The motor runs up
8
When the motor is
running close to the
end-point of upper limit,
press STOP
The motor stops running
9Press either UP or
DOWN
The motor runs step by
step to adjust lower limit
accurately
10 Press CONFIRM key
on the transmitter
The motor sounds "KA
KA", the setting has
complete.
Charging
The motor work with Li-ion battery, please have it charged when the motor stop working or work
faltering. Please plug the charger into the charger hole on the motor head, the charging time is
5 to 6 hours.
FAQ
If nothing works, please check:
●if the motor does not working or works faltering, please charging the motor battery firstly
●If the motor runs to a direction continually, the user didn't setup limit successfully, please re-set
limit.
For instructional purposes, the following options have been shown:
Easy-Lock Chain Winder 'AC' Installation Brackets.
Top Fix installation.
'AC' BracketCover Caps
40mm Motor - Somfy.
Somfy Drive & Crown Wheels.
INSTALLATION
ROLLER BLINDS 40mm MOTORISATION
ENSURE 'NOTCH' OF CROWN WHEEL
LOCKS WITHIN GAP OF MOTOR HEAD.
ASSEMBLY INSTRUCTIONS
STEP 1:
Install Crown Wheel onto40mm Motor. Ensure 'notch' of Crown
Wheellocks within gap of Motor Head.
STEP 2:
Install Drive Wheelonto40mm Motor.
NOTE:
* For Elero Motors, use 'O' ring supplied by Elero to lock Drive Wheel to
40mm Motor.
* For Gaposa Motors, use Gaposa Retaining Clipto lock Drive Wheel
to40mm Motor.
* For Selve Motors, use plastic retaining clip supplied by Selve to lock
Drive Wheelto 40mm Motor.
STEP 3:
Mount 40mm Motor Disk Adaptor onto Motor headwith Counter
Sunk Screws.
ONLY USE WITH GAPOSA
Page 57
=Beep
+
OR
For instructional purposes, the following options have been shown:
Easy-Lock Chain Winder 'AC' Installation Brackets.
Top Fix installation.
'AC' BracketCover Caps
40mm Motor - Somfy.
Somfy Drive & Crown Wheels.
INSTALLATION
ROLLER BLINDS 40mm MOTORISATION
ENSURE 'NOTCH' OF CROWN WHEEL
LOCKS WITHIN GAP OF MOTOR HEAD.
ASSEMBLY INSTRUCTIONS
STEP 1:
Install Crown Wheel onto40mm Motor. Ensure 'notch' of Crown
Wheellocks within gap of Motor Head.
STEP 2:
Install Drive Wheelonto40mm Motor.
NOTE:
* For Elero Motors, use 'O' ring supplied by Elero to lock Drive Wheel to
40mm Motor.
* For Gaposa Motors, use Gaposa Retaining Clipto lock Drive Wheel
to40mm Motor.
* For Selve Motors, use plastic retaining clip supplied by Selve to lock
Drive Wheelto 40mm Motor.
STEP 3:
Mount 40mm Motor Disk Adaptor onto Motor headwith Counter
Sunk Screws.
ONLY USE WITH GAPOSA
Page 57
=
Beep
+
TO REVERSE
DIRECTION
OR
UP
TO REVERSE DIRECTION IF REQUIRED
=
P2 P2
within 4 seconds
within 4 seconds
Jog
Jog
1
1
Cung power before limit seng process is complete will result in loss of pairing.
To reset motor P2 + STOP + P2. Removes all emiers & deletes limits.
Press & quickly release buon on motor head *
PROCEED TO SETTING LIMITS
Press & hold buon on
motor head * for 4secs
Power OFF for 5 seconds &
return to start and reverse
blind direcon.
On Mul - Channel
remote ensure desired
channel is acve rst.
OK
IF POWER IS ALREADY ON
DOWN
UP
Power ON
Check blind direcon

© 2015 Rollease Acmeda © 2015 Rollease Acmeda
Page. 7 of 12
3.5 SETTING TOP & BOTTOM LIMIT
P2 UP P2
ENTER LIMIT SETTING MODE
SET TOP LIMIT
SET BOTTOM LIMIT
P 2
Hold STOP
x5 secs
(as blind approaches
limit) Enter step
mode
1
1
P2
Jog
=
=
Jog
=
Jog
DOWN
UP STOP
STOP
1
If pairing mulple motors to a single channel ensure power is switched o prior to proceeding to the next motor.
Cycle blind up and down rst to sele fabric prior to seng limits
Please cycle blind up and
down to sele fabric prior
to seng limits
Hold STOP
x5 secs
(as blind approaches
limit) Enter step
mode

© 2015 Rollease Acmeda
Blind can be at any point.
Page. 8 of 12
3.6 FAVORITE POSITION
DOWN
drive blind to
desired posion
STOP STOPP 2 =
Jog
1
SETTING FAVORITE POSITION
DELETING FAVORITE POSITION
Operation
Item Item Operation Result Illustration
Setup
bottom
limit
1
Keep pressing the
LIMIT key on the
primary transmitter for
6 seconds above
The motor sounds "KA
KA"
2 Release the key The motor is under the
status of Limit setting
3Press the DOWN key
on the transmitter The motor runs down
4
When the motor is
running close to the
end-point of lower limit,
press STOP
The motor stops running
5Press either UP or
DOWN key
The motor runs step by
step to adjust lower limit
accurately
6Press CONFIRM key
on the transmitter
The motor sounds "KA
KA", the setting has
complete.
Setup
upper limit
7Press UP key on
primary transmitter The motor runs up
8
When the motor is
running close to the
end-point of upper limit,
press STOP
The motor stops running
9Press either UP or
DOWN
The motor runs step by
step to adjust lower limit
accurately
10 Press CONFIRM key
on the transmitter
The motor sounds "KA
KA", the setting has
complete.
Charging
The motor work with Li-ion battery, please have it charged when the motor stop working or work
faltering. Please plug the charger into the charger hole on the motor head, the charging time is
5 to 6 hours.
FAQ
If nothing works, please check:
●if the motor does not working or works faltering, please charging the motor battery firstly
●If the motor runs to a direction continually, the user didn't setup limit successfully, please re-set
limit.
P 2 STOP STOP =Beep x 3
TO SEND BLIND TO FAVORITE POSITION
Hold STOP
x5 secs

© 2015 Rollease Acmeda © 2015 Rollease Acmeda
Page. 9 of 12
3.8. COPY CHANNEL FROM AN EXISTING PRIMARY TRANSMITTER
+
P2 P2
ON PRIMARY TRANSMITTER
=
1
Jog
ON NEW TRANSMITTER
P2
On primary & secondary mul - channel remotes ensure desired channel is acve rst.
3.7 IMPACT DETECTION
= ON
= OFF
Beep
Beep
x 1
x 2
DOWN DOWN
P2

© 2015 Rollease Acmeda
Page. 10 of 12
3.9 ACTIVATE / DEACTIVATE FABRIC TENSION MODE
3.10 SWITCHING BETWEEN AUTO & MANUAL LOCK MODE
= TENSION MODE ON
= TENSION MODE OFF
Beep
Beep
x 1
x 2
P 2
STOP DOWN
= AUTO LOCK
= MANUAL LOCK
Beep x 2
x 5
P 2 UP UP
Fabric Tension Mode must be ON to switch between Auto & Manual Lock Mode
3.11 ADJUSTING TENSION LEVEL
P 2
UP
STOP
= LOW
Beep x 1
= MEDIUM
Beep x 2
= HIGH
Beep x 3
Beep

© 2015 Rollease Acmeda © 2015 Rollease Acmeda
4. TROUBLESHOOTING
Page. 11 of 12
How to delete all transmiers & limits. P2 + STOP + P2.
1
=
Jog x1
+
P 2 P 2
+
PROBLEM CAUSE REMEDY
Shade moves in opposite
direction
Pairing sequence error. refer to section 3.4 to reverse blind direction.
When power is switched on,
the motor refuses to work or
moves slowly
1. Voltage too low
2. Errors in line connection
3. Overload
4. Installation error.
5. Transmitter batteries
are Flat
1. Check voltage is within the rating specified.
2. Check the wiring.
3. Verify motor capacity (torque) has not been
exceeded.
4. Check for excessive friction in assembly. Ensure
tube deductions are correct and that there is
suitable clearance between motor head & bracket.
5. Replace batteries in transmitter.
Motor suddenly cuts off. Rated operating time (4min)
exceeded
Wait approximately 20 minutes for motor to cool down.

ROLLEASE ACMEDA
AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047
T [phone] | F [phone]
Western Australia Branch
Unit 1, 41 Mulgul Road,
Malaga WA 6090
T [phone] | F [phone]
ROLLEASE ACMEDA
USA
200 Harvard Avenue
Stamford, CT 06902 6320
T [phone] | F [phone]
ROLLEASE ACMEDA
EUROPE
Via Conca Del Naviglio 18, Milan
(Lombardia) Italy
T [phone] | F [phone]
Queensland Branch
Unit 2/62 Borthwick Avenue,
Murarrie QLD 4172
[e-mail]
rolleaseacmeda.com
Page. 12 of 12