rollease acmeda RB12 AERO-DUAL User manual

RB12 AERO - DUAL
INSTALLATION MANUAL
February 2017

CONTENTS
February 2016
This manual is to be read in conjunction with the Product Specifications & Assembly manual
SECTION NO.
DESCRIPTION
PAGE NO.
SECTION 1 −ITEMS REQUIRED 1.1
SECTION 2 −INSTALLATION 2.1
PART A – PREPARING INSTALLATION SPACE 2.1
PART B – MOUNTING CLIP INSTALLATION 2.1
PART C – SHADE & CASSETTE INSTALLATION 2.2
PART D – PRETENSION CHECKS 2.3
PART E – SET LIMITS 2.6
SECTION 3 – INSTALLATION SCENARIOS 3.1
PART A – MULTIPLE SHADES INSTALLED SIDE-BY-SIDE 3.1
PART B – FRONT ROLL INSTALLATION 3.1
SECTION 4 − TROUBLESHOOTING 4.1
DISCLAIMER
INTRODUCTION
This Installation manual has been produced by Rollease Acmeda to supply the necessary information for safe and correct installation of this system.
INSTALLERS RESPONSIBILITY
Before installing, please read & ensure you understand the safety information and installation instructions as defined in this installation manual.
•The Installer is responsible to ensure that all installation personnel have been adequately trained on the safe & correct installation and operation.
•The Installer is responsible to ensure that a Job Safety Analysis or Safe Work Method Statement is completed prior to installation to identify hazards, to determine
appropriate risk control measures and to implement the control measures.
•The Installer is responsible to ensure that supporting structures are sound and can adequately support the load.
•The Installer is responsible to ensure that the devises used to anchor the product to the supporting structure are suitable for the application.
•The fasteners provided are intended for fixing to timber. The installer is responsible for selecting fasteners that are suitable for other substrates
SAFETY INFORMATION
•Ensure that electrical works are done only by a LICENSED ELECTRICIAN.
•DO NOT modify any of the components of this system.
PERSONNEL REQUIREMENTS
Only suitably trained/qualified personnel should undertake installation.
DISCLAIMER
Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the completeness or
accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own determination as to its suitability for their
purposes prior to use. Rollease Acmeda assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included
herein. Rollease Acmeda reserves the right to make changes without further notice to any products to improve reliability, function or design.
COPYRIGHT
COPYRIGHT © ROLLEASE ACMEDA 2016
All rights reserved. No part of this document may be reproduced or utilized in any means, by any means, electronic or mechanical including photocopying, recordings, or by any
information storage or retrieval system, without the express permission from Rollease Acmeda.

Page 1.1 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SECTION 1 −ITEMS REQUIRED
TOOLS REQUIRED
•5mm Socket
•Ratchet
•Drill
•Drill Bits
•Measuring Tape
•Pencil
•Screw Driver - Flat Head
SHADE ITEMS REQUIRED
Check you have all items required to complete installation;
1. Shade / Cassette Assembly
2. 2 x End Cap Covers
3. 2 or 3 (as required) x Mounting Clips

Page 2.1 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SECTION 2 −INSTALLATION
PART A – PREPARING INSTALLATION SPACE
STEP 1 – ENSURE TOP OF INSTALLATION SPACE IS LEVEL
PART B – MOUNTING CLIP INSTALLATION
STEP 1 – INSTALL MOUNTING CLIPS TO WALL / CEILING USING APPORPRIATE FIXINGS TO SUIT APPLICATION
WALL MOUNT
CEILING MOUNT
NOTE: Install Mounting Clips as required
Shade Width (ft)
No. Of Brackets
0 - 3.90
2
3.91 – 6.52
3
6.53 – 9.15
4
9.16 +
5

Page 2.2 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
PART C – SHADE & CASSETTE INSTALLATION
STEP 1 – INSTALL SHADE & CASSETTE ONTO MOUNTING CLIPS
Rest Cassette Top on Mounting Clips and rotate to secure. Ensure clips are engaged.

Page 2.3 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
PART D – PRETENSION CHECKS
STEP 1 – CHECK FUNCTIONALITY OF PRE-TENSIONED BACK SHADE
i) PULL Back Bottom Rail or
Back Chain Down to bottom
location
ii) Shade will raise within range
indicated below to find locked
position and provide a 'Release
Allowance' (for raising the
shade)
iii) TUG Back Bottom Rail or
Back Chain
(Shade will automatically rise)
NOTE: As limits are not set,
ensure Bottom Rail is
controlled so shade doesn't
spring into Cassette and
damage fabric
If Bottom Rail raises at the
desired speed, the correct
number of pre-turns have been
assigned. Further adjustments
may be required when limit is
set.
PROCEED TO STEP 2
1.30”
TUG &
LIFT
PULL

Page 2.4 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
If Shade stops midway, insufficient pre-turns have been
assigned.
Pre-turns to be added
If Shade operates too fast, too many pre-turns have been
assigned.
Pre-turns to be removed
ADDING PRE-TURNS
Ensure Shade
is ‘Locked’.
LOCKED SHADE: Shade on way down or reached the bottom
REMOVING PRE-TURNS
Ensure Shade
is ‘Unlocked’.
UNLOCKED SHADE: Shade on way up or reached the top
Insert Socket Ratchet, rotate in direction of '+' on Cassette End
Cap until shade rises to the original start position (top limit)
NOTE: If there is insufficient space to rotate Socket Ratchet
within installation, Shade & Cassette to be removed from
Mounting Clips to undertake process.
Insert Socket Ratchet, rotate in direction of '-' on Cassette End
Cap
NOTE: If there is insufficient space to rotate Socket Ratchet
within installation, Shade & Cassette to be removed from
Mounting Clips to undertake process.

Page 2.5 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
Re-check functionality of shade as per process i, ii & iii outlined
in this step.
Re-check functionality of shade as per process i, ii & iii outlined
in this step.
STEP 2 – CHECK FUNCTIONALITY OF FRONT SHADE
Repeat Step 1 for Front Shade (use Front Chain to operate shade)
For details regarding Shade Operation, refer to Product Specifications Manual, Section 1, Part B
STEP 3 – ALIGN FRONT & BACK SHADES
i) BACK SHADE
Pull Bottom Rail or Back Chain Down to
mid location
ii) FRONT SHADE
Pull Bottom Rail or Front Chain Down to mid location (to match first shade)
Result 1)
Shades Align; no further action required
Result 2)
Slight misalignment; pretension tweaking
required, see below
CORRECTING MISALIGNMENT
Insert Socket Ratchet into Front Shade Cassette End Cap, rotate slightly in required direction until Front Shade is aligned with the
Back Shade.
NOTE: If there is insufficient space to rotate Socket Ratchet within installation, Shade & Cassette to be removed from Mounting Clips
to undertake process.
Re-check alignment of shades as per process i, & ii as outlined in this step.

Page 2.6 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
PART E – SET LIMITS
STEP 1 – REMOVE CASSETTE COVER
STEP 2 – ENSURE LIMITERS ARE UNLOCKED
UNLOCKED: Both Limiter Buttons out
LOCKED: One or both Limiter Buttons in
STEP 3 – SET TOP LIMIT
(Front adjustment installation with back shade shown as example)
i) Set Shade at Top Limit (using Chain or Bottom Rail)
ii)Push Top Limit Button

Page 2.7 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
LIMITER INSTALLATION OPTIONS & BUTTON LOCATIONS
Front Adjustment
**For each limiter, the button closest to the ceiling is the Top
Limit Button**
Bottom Adjustment
(generally pocket installations when front cannot be accessed)
**Top and Bottom Limit Buttons are indicated by arrow
direction on End Caps closest to each button**
NOTE: If the Limiters have been installed in incorrect orientation for accessibility, refer to Assembly Manual, Section 4, Part E, Step
4, Uninstalling Limiter
Repeat for 2
nd
shade
STEP 4 – SET BOTTOM LIMIT
(Front adjustment installation with back shade shown as example)
i) Set Shade at Bottom Limit (using Chain or Bottom Rail)

Page 2.8 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
ii)Manually roll Shade down to bottom of 'Release Allowance'
Alternative Option: To avoid gripping fabric, insert Flat Head Screw Driver into Grooves of Limiter and rotate Shade down to
bottom of 'Release Allowance'
iii)Hold Shade in down position and push Bottom Limit Button
Repeat for 2nd shade
33mm

Page 2.9 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
STEP 5 – TEST LIMITS & SHADE FUNCTIONALITY
Operate Shades up & down
For details regarding shade operation, refer to Product Specifications Manual, Section 1, Part B
ADJUSTING TOP LIMIT
i) Ensure Shade is at current Top Limit
ii) Unlock Top Limit
iii) Set new Top Limit
(refer Step 3)
ADJUSTING BOTTOM LIMIT
i) Ensure Shade at current Bottom Limit
ii) Manually roll Shade down to bottom
of ‘Release Allowance’ (Refer Step 4.ii)
iii) Hold Shade in down position Unlock
Bottom Limit
iv) Set new Bottom Limit
(refer Step 4)
If Pre-Tensioning needs to be adjusted refer to Part D

Page 2.10 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
STEP 6 – TWIST CASSETTE COVER ONTO TOP & CLIP INTO PLACE
STEP 7 – SLIDE END CAP COVERS OVER CASSETTE END CAPS

Page 3.1 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SECTION 3 – INSTALLATION SCENARIOS
PART A – MULTIPLE SHADES INSTALLED SIDE-BY-SIDE
ALIGNING SHADES
i) Install ‘1st Shade’ as per Section 2 of this manual.
Leave ‘1st Shade’ down (Front & Back).
(NOTE: ‘1
st
Shade’ is determined by 'Control Side'; the 'Control Side' is adjacent to the next shade.)
ii) Install 'Central Shade(s)' as per Section 2, Parts B, C & D of this manual.
TIP: Ensure each shade has the same number of pre-tensions as the ‘1st Shade’.
Ensure each shade is aligned correctly with the ‘1st Shade’; refer to Section 2, Part D, Step 3 for correcting slight misalignment.
Set Top & Bottom Limits as per Section 2, Part E of this manual to match ‘1
st
Shade’.
iii) Install ‘Last Shade’ as per Section 2, Parts B, C & D of this manual.
TIP: Ensure each shade has the same number of pre-tensions as the ‘1st Shade’.
Ensure each shade is aligned correctly with the ‘1st Shade’; refer to Section 2, Part D, Step 3 for correcting slight misalignment.
NOTE: If the shade pre-tension is to be adjusted and there is insufficient space to rotate Socket Ratchet within installation, Shade &
Box to be removed from Mounting Clips to undertake process. TIP: Measure the amount of misalignment in shades prior to
removing shade.
Set Top & Bottom Limits as per Section 2, Part E of this manual to match ‘1
st
Shade’.
PART B – FRONT ROLL INSTALLATION
REVERSE INSTALLATION SIDES OF CASSETTE BACK & COVER
BACK ROLL (STANDARD INSTALL)
FRONT ROLL (REVERSE INSTALL)
NOTE: This Front Roll configuration option has limited functionality when installing; the Cassette Back now functions as the ‘Cover’.
The Cassette Back can only be removed when the Screws from the End Caps are removed from each end.
LAST SHADE
CENTRAL SHADE
1st SHADE

Page 4.1 RB12 Aero - DUAL Installation Manual | February 2017
© Copyright 2017 | Rollease Acmeda Group
SECTION 4 −TROUBLESHOOTING
NO.
PROBLEM
CAUSE
SOLUTION
1
Cannot find limit
Limits incorrectly Set
TOP LIMIT
a) Position Shade fully retracted
b) Unlock top limit button
c) Lower Shade to half height
d) Lock top limit button
e) Raise Shade until limit is found
If limit not found, repeat steps a-e
BOTTOM LIMIT
a) Position Shade fully lowered
b) Unlock bottom limit button
c) Raise shade to half height
d) Lock bottom limit button
e) Lower Shade until limit is found
If limit not found, repeat steps a-e