rollease acmeda ZIPSCREEN User manual

Page 1of 5
ULTRA-LOCK MOTOR SETTINGS - Zipscreen Installation Manual | v4.2| August 2019
2019 ©Copyright All Rights Reserved Rollease Acmeda
ULTRA-LOCK MOTOR SETTINGS
STEP 1 –INITIAL SETUP
PAIR MOTOR WITH CONTROLLER
Select channel on controller. Hold P1 button on motor head. Hold STOP on controller.
IMPORTANT Motor Response Motor Response___ _
_______________________ ____________
Consult user manual for your controller for
information on selecting channel.
Motor is now in step mode and ready for setting limits.
CHECK FOR MOTOR DIRECTION
To check travel direction of shade, press UP or DOWN To reverse shade direction, hold both UP and DOWN.
on controller Until the motor responds

Page 2of 5
ULTRA-LOCK MOTOR SETTINGS - Zipscreen Installation Manual | v4.2| August 2019
2019 ©Copyright All Rights Reserved Rollease Acmeda
STEP 2 –SET UPPER LIMIT
Setting limits with this method is only possible during initial set up. Refer to previous page for adjusting motor
limits.
Move shade to the desired highest position by pressing
the UP button on controller To save upper limit, hold UP and STOP
Motor Response___ _
Cycle shade up and down prior to setting limits
fabric.
After setting limits, motor will automatically exit
from initial set-up mode.
STEP 3 –SET LOWER LIMIT (LOCK POSITION)
Setting limits with this method is only possible during initial set up. Refer to Part J for adjusting motor limits.
The motor lower limit must be set correctly between the locking & unlocking position. Jog the motor down to
find the lock position (Jog until you hear BOTH pins click), then set the lower limit.
Move shade to lock position by pressing the DOWN To save lower limit, hold DOWN and STOP.
button on controller.
Motor Response___ _

Page 3of 5
ULTRA-LOCK MOTOR SETTINGS - Zipscreen Installation Manual | v4.2| August 2019
2019 ©Copyright All Rights Reserved Rollease Acmeda
STEP 4 –ACTIVATE FABRIC TENSION MODE
Once the bottom limit is set, FT Mode will need to be activated to operate the Ultra-Lock.
Press P2 on controller. Press UP on controller. Press UP on controller.
FT MODE:
Motor Response___
NO FT MODE:
Motor Response___
Initial setup is complete. You may now operate the shade normally.
ULTRA-LOCK OPERATION (MOTOR OPERATION)
STEP 1 –LOCKING
Press DOWN on the controller. The motor will lower the weight bar to the set bottom limit, then automatically
tension the fabric.
STEP 2 –UNLOCKING
Press UP on the controller. The motor will lower the weight bar past the bottom limit to unlock, then raise the
weight bar continuing to the upper limit.
Note: Make sure that the FT mode is turned ON whilst locking and unlocking the blind. Refer to step 4 for
instructions.

Page 4of 5
ULTRA-LOCK MOTOR SETTINGS - Zipscreen Installation Manual | v4.2| August 2019
2019 ©Copyright All Rights Reserved Rollease Acmeda
ADJUSTING MOTOR LIMITS
STEP 1 –ADJUST UPPER LIMIT
Motor Response___ _ Motor Response___ _
STEP 2 –ADJUST LOWER LIMIT (LOCK POSITION)
The motor lower limit must be set correctly between the locking & unlocking position. Jog the motor
down to find the lock position (Jog until you hear BOTH pins click) then set the lower limit.
Motor Response___ _ Motor Response___ _

Page 5of 5
ULTRA-LOCK MOTOR SETTINGS - Zipscreen Installation Manual | v4.2| August 2019
2019 ©Copyright All Rights Reserved Rollease Acmeda
ULTRA-LOCK OPERATION (MANUAL OPERATION)
SPRING CONTROL
LOCKING
STEP 1 - LOWER THE WEIGHT BAR TOWARDS THE LOCK UNTIL YOU HEAR IT CLICK ONCE
If 2 ‘clicks’ are heard the weight bar has been lowered into the ‘unlock’ position. Raise the weight bar and
try again to lock.
UNLOCKING
STEP 1 - LOWER THE WEIGHT BAR ALL THE WAY DOWN PAST THE LOCKING POINT
STEP 2 - RAISE THE WEIGHT BAR