Savant GPM-CP2R20120-21 User manual

Dual 20 Amp Relay Companion Module - QRG | 009-2129-00 1 of 4 45 Perseverance Way, Hyannis MA 02601
Copyright ©2022 Savant Systems, Inc | 220408 Savant.com | 508.683.2500
120V 20A DUAL RELAY
GPM-C2R20120
MODULE INPUT:
LOAD INPUT:
LOAD OUTPUT:
INDOOR USE ONLY
#12-8 AWG Cu ONLY
HOME AUTOMATION EQUIP
IC ID: 10798A-QP2R20120
FCC ID: PUU-QP2R20120
EXXXXXX
YYWW
120VAC 20A/1HP MAX/CHAN
RES, MOTOR
120VAC 60Hz
120VAC 60Hz
LOAD TYPE:
INPUT OUTPUT
AA
INPUT OUTPUT
BB
PAIR
DO NOT
PRESS ON
SCREEN
REMOVE AFTER
INSTALLATION
CIRCUIT POWER
B
A
A
B
C
E
F
G
D
A
Multi-Page LCD screen that can display the following:
–Power draw and energy usage at each output.
–Firmware, Mac Address, and Regulatory Info.
–UID of the Host that the module is communicating with.
–Real-time Bluetooth status connectivity icon.
BManual Load Switches - Toggle to the ON position to switch
the load on. Toggle to AUTO for normal operation. Switch A
controls output A, Switch B controls output B.
C
PAIR Button - The PAIR button is a multi-use button. The
duration that the button is pressed and held determines the
function that gets initiated:
Press and Release - Cycles through the screens available on
the LCD (POWER > ENERGY > INFO 1 > INFO 2).
Press and hold - Press and hold for 2 second to put the
module into pairing mode. Press and hold for 5 seconds to
reset.
DInput Power Connections - Connect the outputs from two
feeder breakers to inputs A and B on the module. See the
Wiring section below.
EOutput Power Connections - Connect output A and output B
to separate loads. See the Wiring section below.
F120V AC Connection - Plugs into the 120V AC bus bar in the
breaker panel. The voltage on this connection powers the
module.
G
Neutral - The model number of the Companion Module
determines the type of neutral connection available:
– Plug-On Neutral - Positioned on the bottom of the module
is a neutral clip that plugs directly onto the neutral bar.
– Pigtail Neutral - A neutral wire protrudes from the
module’s rear and gets wired to the neutral bar in the
breaker panel.
Minimum Supported Release
Savant OS da Vinci 10.1
Electrical and Safety Characteristics
Screw Tighten Torque 3.0 Nm
Wire Type Copper (Cu) only
Pollution Degree 2
Purpose of Control Operating Control, Smart Relay Control
Module or equivalent
Software Class A
Impulse Voltage 2500V
Supported Load Types
Standard Configuration Relay On/O type loads (home automation)
Standards
Wireless Bluetooth 5 Low Energy (BLE)
–2.4 GHz radio frequency
Regulatory
Safety and Emissions
FCC Part 15 UL ICES 003
Contains FCC ID: PUU-QP2R20120
Contains IC: 10798A-QP2R20120
RoHS Compliant
Recommended Load Center Types
All Eaton CH style modules fit into a ¾inch Eaton CH load center.
Power
Input Power
(powers the module) 120V AC (+/- 10%) @ 60 Hz, 0.1A (max)
Input Power
(from feeder breaker) 120V AC @ max power load
Load Power 2400VA max per channel
(20A resistive load / 1 HP max per channel)
Features of Automatic
Action Type 1.B action
Dimensions and Weights
Length Width Height Weight
Module 4.96 inch
(12.6 cm)
1.46 inch
(3.7 cm)
3.39 inch
(8.61 cm)
.54 lbs
(.24 kg)
Shipping 7.48 inch
(19.0 cm)
4.17 inch
(10.60 cm)
1.69 inch
(4.29 cm)
1.0 lbs.
(.45 kg)
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 5% to 85% Relative Humidity (non-condensing)
Location Indoor Use Only
Features
–Control capability for loads up to 2400VA per channel.
–All Eaton CH style relay modules are compatible with Eaton CH ¾
inch load centers.
–Dynamic management of loads.
–Built-in energy monitoring; +/- .5% revenue grade accuracy / 1 sec
sample time.
–Communicates over the air using Bluetooth Low Energy (BLE)
technology.
–Manual load switches, available on the front panel, can toggle
power to the outputs On and O.
–Color LCD display for easy identification and load status.
Dual 20 Amp Relay Companion Module (120V AC) (Supports Eaton CH Load Centers)
Quick Reference and Installation Guide
Specifications
Box Contents Descriptions
(1) Dual 20 Amp Relay Companion Module (Eaton CH)
–GPM-CP2R20120-21 w/Plug-on Neutral -or-
–GPM-C2R20120-21 w/Pigtail
(1) Product Information and Regulatory Insert (009-1950)
(1) Quick Reference and Installation Guide (this document)
Construction of Control
Open Type Independently mounted for flush mounting

Dual 20 Amp Relay Companion Module - QRG | 009-2129-00 2 of 4 45 Perseverance Way, Hyannis MA 02601
Copyright ©2022 Savant Systems, Inc | 220408 Savant.com | 508.683.2500
–The breaker(s) feeding the module should not be larger than 20 amps.
–Each relay output can switch up to 20 amps.
–To determine the number of breaker panel spaces needed, add the number of spaces required for the circuit breaker(s) to the number of
spaces needed for the module.
• A single pole circuit breaker requires one space.
• A 2-pole circuit breaker requires two spaces.
• Each Companion Module requires two spaces.
–Savant recommends not connecting any mission-critical loads such as medical devices to this relay module.
Important Information
ELECTRIC SHOCK! The 120V AC, 60 Hz source poses an
electrical shock hazard that has the potential to cause serious
injury to installers and end users.
CAUTION! Risk of Electric Shock - More than one disconnect
switch may be required to de-energize the device before
servicing
IMPORTANT! A licensed electrician is required to install any of
Savant’s Relay Companion Modules.
1. Remove power from the breaker panel by switching o the panel’s main breaker.
2. Position and install a circuit breaker into one of the slots in the panel. Press firmly until the breaker is fully seated onto the appropriate bus
bars.
3. Install a second breaker alongside the first.
4. Position and install the Companion Relay Module into the slot where it will be installed. Press firmly until fully seated onto the appropriate bus
bars. This module is typically installed alongside the breakers installed in steps 2 and 3.
HELPFUL! A relay module fills two slots in the breaker panel but connects to only one phase (120V AC). See the diagram below.
5. Refer to the Wiring section below and make the appropriate connections.
Installation into Breaker Panel
Branch Circuit Minimum Size of Conductors
(General circuit wiring, Copper Conductors)
15A 20A 30A 40A 50A 60A
#14 AWG #12 AWG #10 AWG #8 AWG #6 AWG #4 AWG
NOTE: This wiring requirement was based on the National Electric Code
(NEC) (ANSI/NFPA70), Canadian Electric Code, Part 1 (CEC), and local
codes Minimum Size of Conductors.
Plug-on Neutral Bus Bar with ARC Fault Breakers
Wiring
Plug-on Neutral Bus Bar with Standard Breakers
Neutral Bar
Phase A Phase B
Breaker Panel
Gnd
Bar
120VAC
plug-on
neutral bar
Use AFCI / GFCI protection where
required by local regulations
INPUT OUTPUT
OUTPUT
B
A
B
A
INPUT
CIRCUIT POWER
ON
AUTO
PAIR
A B
20A DUAL RELAY
BREAKER
BREAKER
Load 2
Load 1
Neutral Bar
Breaker Panel
Gnd
Bar
120VAC
plug-on
neutral bar
Phase A Phase B
Use AFCI / GFCI protection where
required by local regulations
INPUT OUTPUT
OUTPUT
B
A
B
A
INPUT
CIRCUIT POWER
ON
AUTO
PAIR
A B
20A DUAL RELAY
BREAKER
BREAKER
Load 2
Load 1
Use the diagrams below when wiring the modules. The diagrams cover the following scenarios:
Breaker panel with a plug-on neutral bus bar (with ARC Fault type
feeder breakers).
Breaker panel with a plug-on neutral bus bar (with standard type
feeder breakers).

Dual 20 Amp Relay Companion Module - QRG | 009-2129-00 3 of 4 45 Perseverance Way, Hyannis MA 02601
Copyright ©2022 Savant Systems, Inc | 220408 Savant.com | 508.683.2500
Circuit Test Instructions
Use the instructions below to test the relay modules. The setup requires:
–20 Amp Dual Relay Companion Module.
–(2) loads (20 amps max for each).
–(2) 20 amp circuit breakers.
–Breaker test panel. The type of module determines the type of breaker panel (plug-on neutral or not).
–120V AC source
1. Plug the two feeder circuit breakers and one 20 Amp Dual Relay Companion Module into the circuit breaker test panel.
2. Connect the output from one of the circuit breakers to Input A
on the module.
3. Connect the output from the remaining circuit breaker to Input
B on the module.
4. Connect a load to Output A.
5. Connect a second load to Output B.
6. Connect the unused side of each load to the neutral bus bar in
the breaker panel.
7. On modules that contain a neutral wire, connect the neutral
wire to the neutral bar.
8. Apply power to the breaker panel (not shown in diagram).
9. Toggle the 20 amp feeder breakers to On.
10. To test, toggle the CIRCUIT POWER switches A and B to ON
and verify both loads switch On.
11. Toggle the CIRCUIT POWER switches to AUTO and verify the
loads switch O
6
Load
Load
5
PANEL CIRCUIT
BREAKER
INPUT OUTPUT
OUTPUT
A
INPUT
CIRCUIT POWER
ON
AUTO
PAIR
A B
20A DUAL RELAY
A
BB
Plug-on neutral
bus bar for modules with
a Plug-On neutral clip
120VAC
PANEL CIRCUIT
BREAKER
2
1
3
4
7
9
10
11
IMPORTANT!
–When making connections, observe all general electrical best practices including local wire sizing guidelines.
–The GPM-CP2R20120-21 and GPM-C2R20120-21 modules can accept up to a #12 AWG wire. See the Branch Circuit Minimum Size of
Conductors table on the previous page for wire sizing information.
Standard Neutral Bus Bar with ARC Fault Breakers Standard Neutral Bus Bar with Standard Breakers
Neutral Bar
Neutral wire from the
companion module connects
to the neutral bar
Phase A Phase B
Breaker Panel
Gnd
Bar
Use AFCI / GFCI protection where
required by local regulations
INPUT OUTPUT
OUTPUT
B
A
B
A
INPUT
CIRCUIT POWER
ON
AUTO
PAIR
A B
20A DUAL RELAY
BREAKER
BREAKER
Load 1 Load 2 120VAC
Neutral Bar
Breaker Panel
Gnd
Bar
120VAC
Phase A Phase B
Use AFCI / GFCI protection where
required by local regulations
INPUT OUTPUT
OUTPUT
B
A
B
A
INPUT
CIRCUIT POWER
ON
AUTO
PAIR
A B
20A DUAL RELAY
BREAKER
BREAKER
Load 1 Load 2
Breaker panel without a plug-on neutral bus bar (with ARC Fault type
feeder breakers).
Breaker panel without a plug-on neutral bus bar and standard type
feeder breakers.

Dual 20 Amp Relay Companion Module - QRG | 009-2129-00 4 of 4 45 Perseverance Way, Hyannis MA 02601
Copyright ©2022 Savant Systems, Inc | 220408 Savant.com | 508.683.2500
NOTES
Additional Documentation
–Panel Bridge Controller with PoE (PBC-P1000) QRG
–Savant Panelized Lighting Deployment Guide
Further information is available in the documents listed below and can be accessed via the Savant Customer Community.