Savant SAV-LMP-0300 User manual

Savant® SAV-LMP-0300 Pro System Lamp Control
Quick Reference Guide
For Product Info
SAV-LMP-0300 | 009-1406-00 | 160519
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
Savant.com | 508.683.2500
Box Contents
(1) Savant Pro System Lamp Control (SAV-LMP-0300)
(1) Quick Start Guide
Specifications
Environments
Temperature
32° to 104° F (0° to 40°C)
Humidity
10% to 90% (non-condensing)
Dimensions
Lamp Control
Shipping Package
Height
1.8 in (4.6 cm)
4.1 in (10.41 cm)
Width
3.2 in (8.1 cm)
2.1 in (5.33 cm)
Depth
1.8 in (4.6 cm)
4.1 in (10.41 cm)
Weight
0.20 lb (0.09 kg)
1.0 lb (0.45 kg)
Power
Power Supply
120V AC, 60Hz
Maximum Load
2.1A, 250 W
Standards
Wireless
Wi-Fi® (802.11 b/g/n 2.4 GHz)
Bluetooth
Bluetooth v4.0
Security
WPA1™, WPA2™, WPA1™ + WPA2™, WEP
Regulatory
Safety and
Emissions
FCC Part 15 | UL
Contains FCC ID:
TLZ-CU277
Contains IC:
6100A-CU277
RoHS
Compliant
Minimum Supported Release
Savant OS
da Vinci 8.0
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards listed
in the Specifications Table.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Refer to the Lamp Control, refer to the Savant Pro Lamp Control
Deployment Guide (009-1398-xx) located on the Savant Customer
Community for information on provisioning the Pro Lamp Control.
Network Configuration
To ensure that the IP Address will not change due to a power
outage, a static IP Address or DHCP reservation should be
configured. Savant recommends using DHCP reservation within the
router. By using this method, static IP Addresses for all devices can
be managed from a single UI, avoiding the need to access devices
individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Refer to the SAV-LMP-0300 Pro Lamp Control Deployment Guide
(009-1388-xx) located on the Savant Customer Community for
information on connecting the Pro Lamp Control to the local
network.
Lamp Control
Reset
Button
Located on bottom of Lamp Control. Used to
either reboot or put Lamp Control into Access
Point Provisioning Mode.
Press and Release:
Will turn the Lamp plugged into the Lamp
Control on and off.
Press and Hold:
While powered On, press and hold the button
for 5 seconds until the Status LED begins a
rapid blink (red). After reboot, the Lamp
Control will be in Access Point Provisioning
Mode. (See Rapid Blink below.)
Lamp Control LED States
Off - No Power
On Solid (Green) – Connected to the local network and
communicating with the Savant Host.
On Solid (Yellow) - Lamp is booting.
On Solid (Red): Alert message of a possible overcurrent
condition.
Blinks Once (Yellow) – In Access Point Provisioning Mode
and ready to be provisioned onto the local network.
Blinks Once (Green) – Connected to the local network. Has
been provisioned.
Rapid Blink (Red) - The reset button on bottom of Lamp
Control was held down for at least five seconds. When button
is released, the rapid blink will stop and the Lamp Control will
reboot.
Rapid Blink (Yellow) - The locate feature was activated using
SmartConnect.
Blinking Yellow/Green - Firmware is updating.

SAV-LMP-0300 | 009-1388-00 | 160519
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
Savant.com | 508.683.2500
Connections
Connecting the Lamp Control
1. Plug the Lamp Control directly into a surge protected 120V AC
receptacle/outlet.
2. Plug the cord from a lamp into the receptacle on the Lamp
Control Turn the Lamp Switch to the On position.
3. Verify the lamp is in the On position. To do this, press and
release the reset button on the bottom of the Lamp Control.
This will toggle the lamp On and Off.
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
•Pro Lamp Control Deployment Guide (009-1388-xx)
FCC Interference Statement: Pro Lamp Control
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
−Reorient or relocate the receiving antenna.
−Increase the separation between the equipment and receiver.
−Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
−Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Radiation Exposure Statement: Pro Remote Base
This device meets the government’s requirements for exposure to radio
waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
The exposure standard for wireless device employs a unit of measurement
known as the Specific Absorption Rate, or SAR. The SAR limit set by the
FCC is 1.6W/kg.
*Tests for SAR are conducted using standard operating positions accepted
by the FCC with the device transmitting at its highest certified power level
in all tested frequency bands.
Warnings!
−Risk of Electric Shock. Install in accordance with all regional, national, and local
electrical codes.
−Risk of Serious Injury, Death, or Property Damage or Loss. Install and use
properly-as described in this and other product documents-to avoid danger of
injury, death, or property damage or loss.
−Risk of Serious Injury, Death, or Property Damage or Loss. If you are unsure
about any part of these instructions, consult Customer Service or a qualified
dealer.
−Risk of Overheating. To reduce the risk of overheating and possible damage to
other equipment, install and use properly as described in this and other product
documents.
−For the Savant Lamp Control: Prior to changing a light bulb or performing any
other maintenance to the light fixture, turn off the lamp controller via the Savant
App®or unplug the lamp itself from the Savant Lamp Control.