Savant VOM-VP02H User manual

The Video Processing Output Module, VOM-VP02H, is used to overlay
TrueCommand OSD onto the currently playing video stream. Each
card allows for connection of up to two (2) OSD video streams and
two (2) displays.
Box Contents
(1) VOM-VP02H-06
(1) HDMI Locking Cable (3 feet) (CBL-3LHDMI-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Environmental
Refer to the SmartMediaPro chassis specifications.
Refer to the SmartMediaPro chassis specifications.
Dimensions and Weight
Dimensions and Weight
Height
1.31 in (3.33 cm) - Faceplate
Width
5.11 in (12.98 cm) - Faceplate
Depth
6.98 in (17.73 cm) - Faceplate and Board
Weight
Shipping Weight: 1 lb (0.45 kg)
Power
Power
Power is supplied through the SmartMediaPro chassis when module is
inserted (Do not hot plug module).
Power is supplied through the SmartMediaPro chassis when module is
inserted (Do not hot plug module).
Compliance
Compliance
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Minimum Supported Release
Minimum Supported Release
Savant OS
da Vinci 5.2.1
Rear Panel
Graphics
Input 1 and 2
19-pin type A HDMI female digital video/audio
input
Connect to HDMI or Thunderbolt (with
adapter) on Pro Host for TrueCommand OSD.
HDMI 1 and 2
19-pin type A HDMI female digital video/audio
input
Connect to display for TrueCommand OSD
overlay.
Module
Removal Slot
Insert the module removal tool (included with
chassis) into this slot and pull outwards to
remove the module.
Retaining
screws
M3 x 6 mm Phillips head flush mount screws,
Pre-installed in chassis.
Used to fasten the module to the chassis.
IMPORTANT! Module Installation Precautions
ELECTRIC DISCONNECT!
Power Offthe controller by setting the power switch on the rear of
the chassis to Off(O) and remove the power cord before inserting
or removing any module from the SmartMediaPro chassis. Failure
to do so may cause damage to the equipment.
IMPORTANT! Electrostatic Discharge (ESD) Warning:
Observe the following precautions to avoid damage from electrostatic
discharge (ESD) when handling modules.
•Use an approved ESD wrist or ankle-grounding strap. Ensure the
grounding strap makes good skin contact.
•Connect the clip end of the ground strap to a threaded grounding
stud on the chassis.
•When returning a replaced module to Savant, place the module in the
clamshell package in which it was originally shipped in or a static
shielding bag.
NOTE:
The wrist strap only protects the component from ESD voltages on the
body; ESD voltages on clothing can still cause damage.
VOM-VP02H-06 | 009-0410-02 | 150306
VOM-VP02H-06 | 009-0410-02 | 150306
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
1
of
2
savant.com | 508.683.2500
Video Processing Output Module VOM-VP02H
Quick Reference Guide
For Product Info

Module Installation
Refer to Module installation Precautions above before installing
module.
1. Power Offthe SmartMediaPro Chassis using the power switch
located on the rear of the chassis and disconnect the AC power
cord.
2. Remove the two (2) M3 x 6 mm retaining screws. Set screws
aside as they will be used later in procedure.
3. Align the module board with the two rails located at the bottom
of the opening and gently slide the module all the way until a
slight resistance is felt. This is where the connector on rear of
the PCB gets seated into the chassis connector.
4. Gently press on the module the rest of the way until it seats into
the connector at the rear of the slot and the plate seats against
the chassis.
5. Insert the screws removed in step 2 and tighten.
Module Removal
Refer to Module installation Precautions above before removing
module.
1. Power Offthe SmartMediaPro Chassis using the power switch
located on the rear of the chassis and disconnect the AC power
cord.
2. Remove the two (2) M3 x 6 mm retaining screws. Set screws
aside as they will be used later in procedure.
3. With the notch in the module removal tool (included with
SmartMediaPro chassis) facing downward, insert the tool into
the slot in the module faceplate.
4. Lower the tip of the tool downward to ensure it is hooked
behind the faceplate and with slight outward pressure, pull the
module outward. A slight resistance will be felt as the module is
unseated from the chassis side of the connector.
5. Slide module out until it is completely removed from chassis.
6. If the module is being replaced, refer to the Module Installation
instructions for proper installation procedure.
7. If the module is not being replaced, install a blank plate using
the two (2) M3 x 6 mm screws removed in step 2. This will
ensure that proper airflow through the chassis is retained as well
as preventing dust and debris from entering the chassis.
Wiring and Connections
IMPORTANT!!
The SVR-5000S can only have a single display port connected, a second OSD server is required when using an SVR-5000S host.
VOM-VP02H-06 | 009-0410-02 | 150306
VOM-VP02H-06 | 009-0410-02 | 150306
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
2
of
2
savant.com | 508.683.2500