Saxby Lighting Pillo Plus CCT User manual

www.saxbylighting.com
Instruction manual
108747,108748
Pillo Plus CCT
V1 13/09/2023
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
UK Manufacturer: BH17 7BY
For further information, please visit https://www.lighting-info.co.uk/108747
108747 108748
Technical data
220-240 V~, 50 Hz
Supply
Voltage:
Bulb
Type: 15W LED module (SMD) CCT, 3000/4000/6000K This product contains a light source of energy efficiency class E.
Conformity with all relevant EC
Directive requirements.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
This product is rated at IP65.
IP 65
This product is not suitable for dimming.
Conformity with all relevant UKCA
Directive requirements.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
Care and Safety
This LED's are protected by a PC shade. The shade part must be replaced immediately should it
become cracked or damaged. This fitting must not be used without the PC shade in place.
Replace Cracked Shade
Live Voltages may be present in this unit even when turned off or when completely disconnected.
The power supply is Double Insulated and does
not require connection to an Earth circuit.
Caution! Risk of electric shock!
Check that...
You have correctly identified the wires. The connections are tight. No loose strands have been left out of the connection block.
Reseal the approved outdoor rated external terminal block
Having correctly identified the wiring from your
existing light fitting, remove the existing cabel
from quick fit block then pull the mains wire
through the hole and connect to the quick
fit connection block inside the product in the
following way:
Wiring
Non-replaceable control gear
Non-replaceable light source
SUPPLY LIGHT FITTING
SWITCHED LIVE BROWN (L)
BLUE (N)
NEUTRAL
PUSH DOWN
INSERT CABLE
Having correctly identified the wiring from your light fitting,
pull the wire through the hole and connect to the connection
block(not supplied) in the following way:
This unit is double insulated and must not be earthed. If there
are any incoming earth cables, they must be joined together
and well insulated with good quality insulation tape.
SUPPLY
NEUTRAL
SWITCHED LIVE
LIGHT FITTING
BLUE (N)
BROWN (L)
Fig 1 Fig 2

Warning
Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instruction for future reference.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a careful note of the connections.
This product is suitable for location in or near a marine environment.
Never put anything on the product or hang anything on any part of this product.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
After deciding the layout of the light fittings ensure that the cables are long enough to connect to desired positions.
• Determine the position of your light fitting taking into account the entry position of the cable and the ARROW indicating
which WAY UP the base is to be fitted. Make sure there is sufficient cable coming out of the wall to connect to the terminal
block. Ensure that the mounting surface is solid, preferably a brick or block wall and ensure that there are no other cables or
pipes beneath the surface.
• Press the clips on both side of the lamp body to release the bracket.
• Using the bracket as a template, mark the position of the mounting holes. Drill holes and fit supplied wall plugs
(suitable for masonry only - for other surfaces use appropriate fixings). Feed the incoming mains supply cable through the
grommet entry hole. Fix the bracket to the ceiling or wall using the supplied screws.
The power supply is Double Insulated and does not require connection to an Earth circuit.
This product is colur changing and can be either
warm white (3000K) or cool white (4000K) or
daylight white (6000K).
Choose your preferred colour before installing by
using the CCT switch back of the product.
CCT switch
• Unscrew two screws to open the cover of the terminal block fixed on the product to wire as the detailed wiring diagram.
Then refit the cover.
• Refit the lamp body in place.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.
3000K 4000K 6000K
A
B
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and the
each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes
(not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber sheathed cable.
The mains supply cable must have a minimum cross section area of 1.0mm2.
Cables must be protected using suitable conduit or plastic trunking.
This product can be ceiling and wall mounted.
This product must be mounted out of arms reach.
This product is suitable for outdoor and indoor use.
PIR data for 108748 only
10 lux on/off. 100º detection angle, Max 6m detection
range with 45 sec hold timer function, installation
height Max 4m..
Max. 4m
appro. 100º
This PIR sensor can't be adjusted. default setting as below: Type 1: See wiring Fig 1
1 2
3 4
8-10mm
Wire prepatation
Type 2: See wiring Fig 2
Two kind of the wiring type