Sealey AP2030 User manual

INSTRUCTIONS FOR:
HARDWOOD TOP WORK BENCH
( WITH DRAWS ) MODEL :AP2030
The use of symbols in this document is to attract your attention to possible danger. The symbols and warnings themselves do not eliminate any danger, nor are they substitutes for proper
accident prevention measures.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. CONTENTS
1.1 GENERAL SAFETY
pWARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are
adhered to when using this bench.
3Locate bench in a suitable working area.
3Keep the work area clean, uncluttered and ensure there is adequate lighting.
pWARNING! Use bench on level and solid ground, preferably concrete. Avoid
tarmacadam since the bench may sink into the surface.
3Keep the bench clean and tidy in accordance with good workshop practice.
3Keep children and unauthorised persons away from the working area.
7DO NOT use the bench for any purpose other than that for which it is designed.
7DO NOT undertake work on the bench without the workpiece being adequately
secured. Use clamps or a vice (not included) to secure the workpiece. Available from your
Sealey dealer.
7DO NOT use the bench out of doors.
7DO NOT get the bench wet or use in damp or wet locations or areas where
there is condensation.
7DO NOT clean the bench with any solvents which may damage the paint surface or the
protective coating on the wooden top.
AP2030 - 2 - 120702
01284 757500
E-mail: [e-mail]
01284 703534
Sole UK Distributor, Sealey Group,
Bury St. Edmunds, Suffolk.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: Call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
2.0 Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make
immediate contact with your Sealey dealer.

3. ASSEMBLY
STEP 1. Take two crossrails (B) and bolt them
to the cabinet sides (A) using 8 bolts (O), 8
lock washers(P), and 8 nuts (Q). Ensure that
the pairs of holes that accept the corner braces
are facing downwards. ( Refer to STEP 7.)
STEP 2. Bolt the two centre supports (C) to the
front and back crossrails respectively using 4
bolts (O), 4 lock washers(P), and 4 nuts (Q).
STEP 3. Bolt left & right slide panels (D) & (E)
into position using 8 bolts (O), 8 lock washers
(P), and 8 nuts (Q). Fix 5 left hand female
slides (L), onto slide panel (D) and 5 right hand
female slides (L), onto slide panel (E)
Refer to Diagram 11 on how to fit slides.
STEP 4. Take two crossrails (B) and bolt them
to the cabinet sides (A) and centre supports (C)
using 12 bolts (O), 12 lock washers (P), and 12
nuts (Q).
STEP 5. Take the two draw stops (G) and one
back panel (F) and bolt them to the back of the
cabinet with the draw stops between the panel
and the cabinet. Bolt the other back wall panel
into position using bolts (O), lock washers (P),
and nuts (Q).
STEP 6. Bolt the two shelf components (H) into
position in the left hand compartment using 8
bolts (O), 8 lock washers(P), and 8 nuts (Q).
AP2030 - 2 - 120702

01284 757500
E-mail: [e-mail]
01284 703534
Sole UK Distributor, Sealey Group,
Bury St. Edmunds, Suffolk.
STEP 7. Turn the cabinet upside down and
screw in the four adjustable leg levellers (R).
Bolt the four corner braces (I) into position
using 16 bolts (O), 16 lock washers (P), and 16
nuts (Q)
STEP 8. Place the wooden top (N) face down
on a flat, clean, smooth surface. Place the
cabinet upside down on the wooden top and
align it with the four pre-drilled holes. Fix with
the four hex head screws (S).
STEP 10. Attach a left hand female slide (K) to
left hand side of each draw and a right hand
female slide (K) to the right hand side of each
draw (see diagram 11). Engage each draw onto
the protruding male slides and push fully home,
then open the draw to check that it is retained.
Diagram 11. Orientate each slide as shown in the diagram above with the rear hook pointing
towards the rear of the draw or the rear of the cabinet. Put the rear hook on each slide into the
square hole nearest the back of the draw or the back of the cabinet and push the slide backwards
to engage the hook. Swivel the front of the slide up or down slightly until the other two hooks appear
in the other two holes. Keep the rear face of the slide up against the draw or slide panel. On the
draws pull the slide sharply upwards to engage it. On the cabinet push the slides down to engage.
STEP 9. Take the 10 male slide components
(M) and slide 5 onto the female slides on the
left of the draw compartment and 5 onto the
female slides on the right hand side of the draw
compartment. Push them fully in to engage
them, then pull them out to the stop point.
AP2030 - 2 - 120702