Seaside Casual 016 User manual

Page 1
REV A
Seaside Casual Furniture | 11 Industrial Drive Coventry, RI 02816 | 800-809-3114 | [e-mail]
Adirondack Shellback
Glider
(016 Double)
(116 Single)
1PLEASE READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING.
Carefully remove contents from box. Make sure that all parts and hardware are
included using the Parts List below. 2 People will be required for this assembly.
WARRANTY QUESTIONS OR COMMENTS PLEASE CALL TOLL FREE AT 1-800-809-3114
Part Code: 316-1/4-20-50B
50mm Connector Bolt
Part Code: ZINC-4A
Actual Size
4mm Allen Wrench
Part Code: 316-8X1-3/4PFDS
1-3/4” Phillips Head Screw
Seat Side Assemblies
x 1
5/16” Flat Washer
Seat Assembly
Base Side Assemblies
7 1/2” Bearing Strap
Stretchers and Aprons
1 1/2” Phillips Pan Head Screw
1” Phillips Pan Head Screw
5/16” Lock Nut
Bungs
x 1
x 1 x 1
x 1
x 8
x 6
x 8
x 1 x 8 x 25
x 2
Part Code: 316-1/4-20-1PPMS
x 4
Part Code: 304-7.5GBS
x 10
Back Assembly
x 16
ASSEMBLY INSTRUCTIONS
4mm Allen Wrench (included); #2 Phillips Head Screwdriver;
#3 Phillips Head Screwdriver, 1/2” Wrench or Socket.
Tools Required:
Actual Size Actual Size
Actual Size Actual Size
5/8“ 3/8“
Part Code: 18/8-5/16-1.5PPMS
x 3
x 2
Actual Size
Actual Size

Page 2
REV A
2ATTACH SEAT TO SIDE
ASSEMBLIES
Align counter-bored holes in Seat Assembly
with threaded inserts in Side Assembly. Attach
using (5) 50mm Connector Bolts. Do not over
tighten.
Repeat process for other side.
Align Back Assembly with seat supports and
arms. Attach using (3) 1-3/4” Phillips Head
Screws thru Seat Supports into Lower yoke of
Back Assembly, and (2) 1” Phillips Pan Head
Screws from upper yoke into threaded inserts
in arms.
Align Short Stretcher with notch in Side
Assembly. Secure using (4) 1-3/4” Phil-
lips Head Screws thru pre-drilled holes
in stretcher.
Repeat process for other side
3ATTACH BACK ASSEMBLY
5ATTACH SHORT STRETCHER
TO SIDE ASSEMBLIES
Align Aluminum on Apron with the
notch in the middle seat support (016
only). Attach Apron to front of seat us-
ing (3) 1-3/4” Phillips Head Screws (2 for
116). Plug holes with 3/8” Bungs.
Repeat process for rear of seat.
4ATTACH APRONS TO SEAT

Page 3
REV A
Secure Bearing Straps to Base Assembly using
(2) 1-1/2” Phillips Pan Head screws (4) 5/16”
Flat washers (1 before and 1 after bearing strap)*
and (2) 5/16” Lock Nuts with a #3 Phillips
Screwdriver and a 1/2” Wrench. Plug holes in
base with (2) 5/8” plugs.
Repeat process for other side.
IF BOLT DOES NOT ENGAGE NYLON IN LOCK NUT, REMOVE 1 OR
BOTH WASHERS IF NECESSARY TO ENSURE A TIGHT FIT.
Secure Bearing Straps to Seat Assembly using (2)
1-1/2” Phillips Pan Head screws (4) 5/16” Flat
washers (1 before and 1 after bearing strap)* and
(2) 5/16” Lock Nuts with a #3 Phillips Screw-
driver and a 1/2” Wrench. Plug holes in legs
with (2) 5/8” plugs.
Repeat process for other side.
ATTACH REAR STRETCHER
TO REAR LEGS
7ATTACH BEARING STRAPS TO
BASE
8ATTACH SEAT TO BEARING
STRAPS
*
Align (2) Long Stretchers with the notches in the
lower leg of the Base Side. Secure using (4) 1-
3/4” Phillips Head Screws.
Repeat process for other side.
6ATTACH LONG STRETCHERS
TO BASE SIDES
With Glider upside down, rock the base so that
the notch in the middle upright is accessible. At-
tach long stretcher to base using (2) 1-3/4” Phil-
lips Head Screws.
Repeat process for other side.
9ATTACH MIDDLE STRETCHER