SEW-Eurodrive MOVI-C MFC1 FHX25A-N User manual

*26872137_1221*
Drive Technology \ Drive Automation \ System Integration \ Services
Operating Instructions
Decentralized Motion and Logic Controller
MOVI-C® FIELD CONTROLLER standard/advanced
MFC1../FHX
Edition 12/2021 26872137/EN

SEW-EURODRIVE—Driving the world

Table of contents
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 3
Table of contents
1 General information.................................................................................................................. 8
1.1 About this documentation ...............................................................................................8
1.2 Other applicable documentation .....................................................................................8
1.3 Structure of the safety notes ...........................................................................................8
1.3.1 Meaning of signal words ................................................................................ 8
1.3.2 Structure of section-related safety notes........................................................ 8
1.3.3 Structure of embedded safety notes .............................................................. 9
1.4 Decimal separator in numerical values ...........................................................................9
1.5 Rights to claim under limited warranty ............................................................................9
1.6 Product names and trademarks....................................................................................10
1.6.1 Trademark of Beckhoff Automation GmbH .................................................. 10
1.7 Copyright notice ............................................................................................................10
2 Safety notes ............................................................................................................................ 11
2.1 Preliminary information .................................................................................................11
2.2 Duties of the user..........................................................................................................11
2.3 Target group .................................................................................................................12
2.4 Network security and access protection .......................................................................12
2.5 Designated use .............................................................................................................13
2.5.1 Restrictions under the European WEEE Directive 2012/19/EU ................... 13
2.6 Functional safety technology ........................................................................................13
2.7 Transportation...............................................................................................................13
2.8 Installation/assembly.....................................................................................................13
2.8.1 Restrictions of use........................................................................................ 14
2.9 Protective separation ....................................................................................................15
2.10 Electrical installation .....................................................................................................15
2.10.1 Stationary application................................................................................... 15
2.11 Startup/operation ..........................................................................................................16
2.11.1 Switch disconnector ..................................................................................... 16
3 Device structure ..................................................................................................................... 17
3.1 MOVI-C® FIELD CONTROLLER Standard/Advanced .................................................17
3.2 Cable entry position ......................................................................................................18
3.2.1 MFC1.. design.............................................................................................. 18
3.3 Nameplate position .......................................................................................................19
3.3.1 MFC1.. design.............................................................................................. 19
3.4 Example nameplate and type designation ....................................................................19
3.4.1 Nameplate.................................................................................................... 19
3.4.2 Type designation.......................................................................................... 20
3.5 Examples for the optional nameplate "Plug connector positions".................................21
3.5.1 MFC1.. design.............................................................................................. 21
3.6 Electronics ....................................................................................................................22
3.6.1 Connection box and electronics cover (internal) .......................................... 22
3.6.2 Electronics cover (outside)........................................................................... 23
3.7 Example nameplate and type designation of the electronics........................................24
3.7.1 Nameplate.................................................................................................... 24
26872137/EN – 12/2021

Table of contents
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
4
3.7.2 Type designation of the electronics cover (controller).................................. 24
3.8 Example nameplate and type designation of the connection unit.................................25
3.8.1 Nameplate.................................................................................................... 25
3.8.2 Type designation of the connection unit....................................................... 25
4 Mechanical installation .......................................................................................................... 26
4.1 Installation notes ...........................................................................................................26
4.2 Required tools and resources .......................................................................................26
4.3 Tolerances for torque ratings ........................................................................................26
4.4 Installation requirements...............................................................................................26
4.5 Installing the device ......................................................................................................27
4.5.1 Notes............................................................................................................ 27
4.5.2 Electronics cover.......................................................................................... 27
4.6 Mounting the device......................................................................................................30
4.6.1 MFC1.. design.............................................................................................. 30
4.7 Mounting the device with mounting panel M01.............................................................31
4.7.1 MFC1.. design.............................................................................................. 31
4.8 Tightening torques ........................................................................................................32
4.8.1 Blanking plugs.............................................................................................. 32
4.8.2 Cable glands ................................................................................................ 33
4.8.3 Electronics cover.......................................................................................... 34
5 Electrical installation.............................................................................................................. 35
5.1 Installation planning taking EMC aspects into account.................................................35
5.1.1 Notes on arranging and routing installation components ............................. 35
5.1.2 EMC-compliant installation........................................................................... 35
5.1.3 Cable selection, routing and shielding ......................................................... 35
5.1.4 Equipotential bonding................................................................................... 36
5.2 Equipotential bonding at the connection box ................................................................37
5.3 Installation instructions..................................................................................................38
5.3.1 Permitted voltage systems ........................................................................... 38
5.3.2 Connecting supply system cables................................................................ 38
5.3.3 Permitted cable cross section of terminals................................................... 39
5.3.4 Actuating the line terminals X1_a, X1_b ...................................................... 40
5.3.5 Actuating control terminals X9 ..................................................................... 40
5.3.6 Residual current device................................................................................ 40
5.3.7 Line contactor............................................................................................... 41
5.3.8 Notes on PE connection............................................................................... 42
5.3.9 Installation above 1000m asl....................................................................... 43
5.3.10 Protection devices........................................................................................ 43
5.4 Installation topology (installation with PAC hybrid cable)..............................................44
5.5 Terminal assignment.....................................................................................................45
5.6 Connection diagram......................................................................................................47
5.7 Communication interfaces ............................................................................................48
5.7.1 CAN system bus .......................................................................................... 48
5.7.2 RS485 interface ........................................................................................... 48
5.8 Cable routing and cable shielding.................................................................................48
26872137/EN – 12/2021

Table of contents
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 5
5.8.1 Installation with separately routed Ethernet cable........................................ 48
5.8.2 Installation with PA hybrid cable .................................................................. 50
5.8.3 Installation with PAC hybrid cable................................................................ 51
5.9 EMC cable glands.........................................................................................................52
5.9.1 Cable shielding............................................................................................. 52
5.9.2 Assembly of EMC cable glands ................................................................... 52
5.10 Plug connectors ............................................................................................................53
5.10.1 Representation of connections..................................................................... 53
5.10.2 Connection cables........................................................................................ 53
5.10.3 Plug connector positions, connection box.................................................... 55
5.10.4 Plug connector positions at the electronics cover ........................................ 58
5.10.5 Plug connector variants................................................................................ 59
5.10.6 Using plug connectors assembled by yourself............................................. 62
5.11 Assignment of optional plug connectors .......................................................................64
5.11.1 X1203_1 and X1203_2: AC 400V connection............................................. 64
5.11.2 X2203_1 and X2203_2: AC400V connection............................................. 70
5.11.3 X2326_1 and X2326_2: PAC connection for AC400V, DC24V backup
voltage and communication, output ............................................................. 76
5.11.4 X2327_1 and X2327_2: PA connection for AC400V and DC24V backup
voltage, output.............................................................................................. 81
5.11.5 X1523: DC24V backup voltage, input ........................................................ 85
5.11.6 X2313, X2313_1 and X2313_2: DC24V backup voltage, output ............... 88
5.11.7 X4251_1 and X4251_2: EtherCAT®/SBusPLUS, output .................................. 91
5.12 Assignment of the plug connectors in the connection unit............................................92
5.12.1 X43_1 and X43_2: Connection of EtherCAT®/SBusPLUS for drive units
(subnetwork) ................................................................................................ 92
5.13 Plug connector assignment at the electronics cover.....................................................95
5.13.1 X4224: Engineering interface (Ethernet)...................................................... 95
5.13.2 X4233_1: Fieldbus/Ethernet interface, port 1............................................... 96
5.13.3 X4233_2: Fieldbus/Ethernet interface, port 2............................................... 97
5.14 PC connection...............................................................................................................98
5.14.1 Connection via Ethernet............................................................................... 98
6 Startup ................................................................................................................................... 100
6.1 Startup notes...............................................................................................................100
6.2 Startup requirements ..................................................................................................101
6.3 DIP switch ...................................................................................................................101
6.3.1 Overview .................................................................................................... 101
6.4 Setting a user-defined IP address (optional)...............................................................103
6.5 Connecting the engineering PC and MOVI‑C®FIELD CONTROLLER......................104
6.6 Inserting devices in MOVISUITE®..............................................................................105
7 Operation............................................................................................................................... 109
7.1 Switch disconnector ....................................................................................................109
8 Service................................................................................................................................... 110
8.1 Evaluating fault messages ..........................................................................................110
8.1.1 MOVISUITE®.............................................................................................. 110
26872137/EN – 12/2021

Table of contents
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
6
8.2 Resetting fault messages............................................................................................110
8.3 Description of status and operating displays ..............................................................111
8.3.1 PROFINET IO LED displays ...................................................................... 111
8.3.2 LEDs for EtherNet/IP™, Modbus TCP ....................................................... 112
8.3.3 General LEDs............................................................................................. 112
8.3.4 Bus-specific LEDs for PROFINET IO......................................................... 115
8.3.5 Bus-specific LEDs for EtherNet/IP™ and ModbusTCP............................. 116
8.4 Fault/error table...........................................................................................................117
8.4.1 Fault 150 Controller firmware – general device fault.................................. 117
8.4.2 Fault 151 controller firmware – License Manager fault .............................. 118
8.5 Device replacement ....................................................................................................119
8.5.1 Notes.......................................................................................................... 119
8.5.2 Replacing the electronics cover ................................................................. 119
8.5.3 Replacing the SD memory card ................................................................. 120
8.5.4 Device replacement ................................................................................... 121
8.6 Device replacement in MOVISUITE® .........................................................................121
8.6.1 Configuration data update.......................................................................... 121
8.6.2 Firmware update ........................................................................................ 122
8.6.3 Logging function......................................................................................... 125
8.7 SEW‑EURODRIVE Service ........................................................................................126
8.7.1 Sending in a device for repair .................................................................... 126
8.8 Shutdown ....................................................................................................................126
8.9 Storage .......................................................................................................................126
8.10 Extended storage........................................................................................................127
8.10.1 Storage conditions ..................................................................................... 127
8.10.2 Electronics.................................................................................................. 128
8.11 Waste disposal............................................................................................................128
9 Inspection and maintenance ............................................................................................... 129
9.1 Inspection and maintenance work ..............................................................................129
9.1.1 Preliminary work regarding inspection and maintenance........................... 129
9.1.2 Connection cables...................................................................................... 129
9.1.3 Replacing the gasket between connection box and electronics cover....... 130
10 Technical data and dimension sheets................................................................................ 134
10.1 Markings .....................................................................................................................134
10.1.1 CE marking ................................................................................................ 134
10.1.2 UKCA mark ................................................................................................ 134
10.1.3 UL approval (in preparation) ...................................................................... 134
10.1.4 EAC (in preparation) .................................................................................. 134
10.1.5 UA.TR (Declaration of conformity to Technical Regulation of Ukraine) ..... 135
10.1.6 RCM approval ............................................................................................ 135
10.1.7 CMIM.......................................................................................................... 135
10.2 General information ....................................................................................................136
10.2.1 Air admission and accessibility .................................................................. 136
10.3 Technical data.............................................................................................................136
10.3.1 General technical data ............................................................................... 136
26872137/EN – 12/2021

Table of contents
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 7
10.3.2 Environmental conditions ........................................................................... 139
10.3.3 Derating factors.......................................................................................... 140
10.3.4 Current carrying capacity of terminals........................................................ 140
10.3.5 Technical data for PROFINETIO interface................................................ 141
10.3.6 Technical data for the EtherNet/IP™, ModbusTCP interface.................... 142
10.4 Port overview ..............................................................................................................143
10.4.1 Interface description................................................................................... 143
10.4.2 Engineering interface ................................................................................. 143
10.4.3 PROFINET ................................................................................................. 143
10.4.4 EtherNet/IP™ ............................................................................................. 144
10.5 Screw fittings...............................................................................................................145
10.5.1 Cable glands / screw plugs / pressure compensation................................ 145
10.5.2 Cable glands, Ethernet cable ..................................................................... 146
10.5.3 Screw fittings: Plug connectors .................................................................. 146
10.6 Mounting positions ......................................................................................................147
10.6.1 MFC1.. design............................................................................................ 147
10.7 Device dimension drawings ........................................................................................148
10.7.1 MFC1.. design............................................................................................ 148
10.7.2 MFC1.. design with switch disconnector .................................................... 149
10.8 Dimension drawings of plug connectors in the electronics cover ...............................150
10.9 Dimension drawings of plug connectors in the connection box ..................................151
10.9.1 MFC1.. design............................................................................................ 151
10.10 Dimension drawing of M01 mounting panel................................................................153
10.10.1 MFC1.. design............................................................................................ 153
Index ...................................................................................................................................... 154
26872137/EN – 12/2021

1General information
About this documentation
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
8
1 General information
1.1 About this documentation
The documentation at hand is the original.
This documentation is an integral part of the product. The documentation is intended
for all employees who perform work on the product.
Make sure this documentation is accessible and legible. Ensure that persons respon-
sible for the systems and their operation as well as persons who work on the product
independently have read through the documentation carefully and understood it. If you
are unclear about any of the information in this documentation or if you require further
information, contact SEW‑EURODRIVE.
1.2 Other applicable documentation
Observe the corresponding documentation for all additional components.
1.3 Structure of the safety notes
1.3.1 Meaning of signal words
The following table shows the grading and meaning of the signal words for safety
notes.
Signal word Meaning Consequences if disregarded
DANGER Imminent hazard Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the product or its envi-
ronment
INFORMATION Useful information or tip: Simplifies
handling of the product.
1.3.2 Structure of section-related safety notes
Section-related safety notes do not apply to a specific action but to several actions
pertaining to one subject. The hazard symbols used either indicate a general hazard
or a specific hazard.
This is the formal structure of a safety note for a specific section:
SIGNAL WORD
Type and source of hazard.
Possible consequence(s) if disregarded.
• Measure(s) to prevent the hazard.
26872137/EN – 12/2021

1
General information
Decimal separator in numerical values
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 9
Meaning of the hazard symbols
The hazard symbols in the safety notes have the following meaning:
Hazard symbol Meaning
General hazard
Warning of dangerous electrical voltage
Warning of hot surfaces
Warning of automatic restart
1.3.3 Structure of embedded safety notes
Embedded safety notes are directly integrated into the instructions just before the de-
scription of the dangerous action.
This is the formal structure of an embedded safety note:
 SIGNAL WORD! Type and source of hazard. Possible consequence(s) if disre-
garded. Measure(s) to prevent the hazard.
1.4 Decimal separator in numerical values
In this document, a period is used to indicate the decimal separator.
Example: 30.5kg
1.5 Rights to claim under limited warranty
Read the information in this documentation. This is essential for fault-free operation
and fulfillment of any rights to claim under limited warranty. Read the documentation
before you start working with the product.
26872137/EN – 12/2021

1General information
Product names and trademarks
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
10
1.6 Product names and trademarks
The brands and product names in this documentation are trademarks or registered
trademarks of their respective titleholders.
1.6.1 Trademark of Beckhoff Automation GmbH
EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff
Automation GmbH, Germany.
1.7 Copyright notice
©2021SEW‑EURODRIVE. All rights reserved. Unauthorized reproduction, modifica-
tion, distribution or any other use of the whole or any part of this documentation is
strictly prohibited.
26872137/EN – 12/2021

2
Safety notes
Preliminary information
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 11
2 Safety notes
2.1 Preliminary information
The following general safety notes serve the purpose of preventing injury to persons
and damage to property. They primarily apply to the use of products described in this
documentation. If you use additional components, also observe the relevant warning
and safety notes.
2.2 Duties of the user
As the user, you must ensure that the basic safety notes are observed and complied
with. Make sure that persons responsible for the machinery and its operation as well
as persons who work on the device independently have read through the documenta-
tion carefully and understood it.
As the user, you must ensure that all of the work listed in the following is carried out
only by qualified specialists:
• Setup and installation
• Installation and connection
• Startup
• Maintenance and repairs
• Shutdown
• Disassembly
Ensure that the persons who work on the product pay attention to the following regula-
tions, conditions, documentation, and information:
• National and regional safety and accident prevention regulations
• Warning and safety signs on the product
• All other relevant project planning documents, installation and startup instructions,
and wiring diagrams
• Do not assemble, install or operate damaged products
• All system-specific specifications and conditions
Ensure that systems in which the product is installed are equipped with additional
monitoring and protection devices. Observe the applicable safety regulations and leg-
islation governing technical work equipment and accident prevention regulations.
26872137/EN – 12/2021

2Safety notes
Target group
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
12
2.3 Target group
Specialist for me-
chanical work
Any mechanical work may be performed only by adequately qualified specialists. Spe-
cialists in the context of this documentation are persons who are familiar with the
design, mechanical installation, troubleshooting, and maintenance of the product who
possess the following qualifications:
• Qualifications in the field of mechanics in accordance with the national regulations
• Familiarity with this documentation
Specialist for elec-
trotechnical work
Any electrotechnical work may be performed only by electrically skilled persons with a
suitable education. Electrically skilled persons in the context of this documentation are
persons who are familiar with electrical installation, startup, troubleshooting, and main-
tenance of the product who possess the following qualifications:
• Qualifications in the field of electrical engineering in accordance with the national
regulations
• Familiarity with this documentation
Additional qualifi-
cations
In addition to that, these persons must be familiar with the valid safety regulations and
laws, as well as with the requirements of the standards, directives, and laws specified
in this documentation.
The persons must have the express authorization of the company to operate, pro-
gram, parameterize, label, and ground devices, systems, and circuits in accordance
with the standards of safety technology.
Instructed persons All work in the areas of transport, storage, installation, operation and waste disposal
may only be carried out by persons who are trained and instructed appropriately.
These instructions must enable the persons to carry out the required activities and
work steps safely and in accordance with regulations.
2.4 Network security and access protection
A bus system makes it possible to adapt electronic drive technology components to
the particulars of the machinery within wide limits. There is a risk that a change of pa-
rameters that cannot be detected externally may result in unexpected but not uncon-
trolled system behavior and may have a negative impact on operational safety, system
availability, or data security.
Ensure that unauthorized access is prevented, especially with respect to Ethernet-
based networked systems and engineering interfaces.
Use IT‑specific safety standards to increase access protection to the ports. For a port
overview, refer to the respective technical data of the device in use.
26872137/EN – 12/2021

2
Safety notes
Designated use
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 13
2.5 Designated use
The product is intended for installation in electrical plants or machines.
In case of installation in electrical systems or machines, startup of the product is pro-
hibited until it is determined that the machine meets the requirements stipulated in the
local laws and directives. For Europe, Machinery Directive 2006/42/EC as well as the
EMC Directive 2014/30/EU apply. Observe EN60204-1 (Safety of machinery - elec-
trical equipment of machines). The product meets the requirements stipulated in the
Low Voltage Directive 2014/35/EU.
The standards given in the declaration of conformity apply to the product.
Technical data and information on the connection conditions are provided on the
nameplate and in chapter "Technical data" in the documentation. Always comply with
the data and conditions.
Unintended or improper use of the product may result in severe injury to persons and
damage to property.
Do not use the product as a climbing aid.
2.5.1 Restrictions under the European WEEE Directive 2012/19/EU
You may use options and accessories from SEW-EURODRIVE exclusively in connec-
tion with products from SEW-EURODRIVE.
2.6 Functional safety technology
The product must not perform any safety functions without a higher-level safety sys-
tem unless explicitly allowed by the documentation.
2.7 Transportation
Inspect the shipment for damage as soon as you receive the delivery. Inform the ship-
ping company immediately about any damage. If the product is damaged, it must not
be assembled, installed or started up.
Observe the following notes when transporting the device:
• Ensure that the product is not subject to mechanical impact.
• Before transportation, cover the connections with the supplied protection caps.
• Only place the product on the cooling fins or on the side without connectors during
transportation.
If necessary, use suitable, sufficiently dimensioned handling equipment.
Observe the information on climatic conditions in chapter Technical data of the docu-
mentation.
2.8 Installation/assembly
Ensure that the product is installed and cooled in accordance with the regulations in
the documentation.
26872137/EN – 12/2021

2Safety notes
Installation/assembly
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
14
Protect the product from excessive mechanical strain. The product and its mounted
components must not protrude into the path of persons or vehicles. Ensure that no
components are deformed or no insulation spaces are modified, particularly during
transportation. Electrical components must not be mechanically damaged or de-
stroyed.
Observe the notes in chapter Mechanical installation in the documentation.
2.8.1 Restrictions of use
The following applications are prohibited unless the device is explicitly designed for
such use:
• Use in potentially explosive atmospheres
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, and radiation
• Operation in applications with impermissibly high mechanical vibration and shock
loads in excess of the regulations stipulated in EN61800-5-1
•Use at an elevation of more than 3800m above sea level
The product can be used at altitudes above 1000 m above sea level up to 3800 m
above sea level under the following conditions:
• The reduction of the nominal output current and/or the line voltage is considered
according to the data in chapter Technical data in the documentation.
• Above 2000m above sea level, the air and creeping distances are only sufficient
for overvoltage class II according to EN60664. At altitudes above 2000m above
sea level, limiting measures must be taken which reduce the line side overvoltage
from category III to category II for the entire system.
• If a protective electrical separation (in accordance with EN 61800‑5‑1 and
EN 60204‑1) is required, then implement this outside the product at altitudes of
more than 2000m above sea level.
26872137/EN – 12/2021

2
Safety notes
Protective separation
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 15
2.9 Protective separation
The product meets all requirements for protective separation of power and electronics
connections in accordance with EN 61800-5-1. The connected signal circuits must
meet requirements according to SELV (Safety Extra Low Voltage) or PELV (Protective
Extra Low Voltage) to ensure protective separation. The installation must meet the re-
quirements for protective separation.
2.10 Electrical installation
Ensure that all of the required covers are correctly attached after carrying out the elec-
trical installation.
Make sure that preventive measures and protection devices comply with the applica-
ble regulations (e.g. EN60204-1 or EN61800-5-1).
2.10.1 Stationary application
Necessary preventive measure for the product:
Type of energy transfer Preventive measure
Direct power supply • Ground connection
26872137/EN – 12/2021

2Safety notes
Startup/operation
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
16
2.11 Startup/operation
Observe the safety notes in chapters Startup and "Operation"(→2109) in this docu-
mentation.
Make sure the connection boxes are closed and screwed before connecting the sup-
ply voltage.
Depending on the degree of protection, products may have live, uninsulated, and
sometimes moving or rotating parts as well as hot surfaces during operation.
When the device is switched on, dangerous voltages are present at all power connec-
tions as well as at any connected cables and terminals. This also applies even when
the product is inhibited and the motor is at standstill.
Do not separate the connection to the product during operation. This may result in
dangerous electric arcs damaging the product.
If you disconnect the product from the voltage supply, do not touch any live compo-
nents or power connections because capacitors might still be charged. Observe the
following minimum switch-off time:
5minutes.
Observe the corresponding information signs on the product.
The fact that the operation LED and other display elements are no longer illuminated
does not indicate that the product has been disconnected from the supply system and
no longer carries any voltage.
Mechanical blocking or internal protective functions of the product can cause a motor
standstill. Eliminating the cause of the problem or performing a reset may result in the
drive restarting automatically. If, for safety reasons, this is not permitted for the drive-
controlled machine, first disconnect the product from the supply system and then start
troubleshooting.
Risk of burns: The surface temperature of the product can exceed 60°C during opera-
tion. Do not touch the product during operation. Let the product cool down before
touching it.
2.11.1 Switch disconnector
The switch disconnector only disconnects the line terminals for the connected external
devices. The line terminals of the device are still connected to the line voltage after the
switch disconnector is activated.
26872137/EN – 12/2021

3
Device structure
MOVI-C® FIELD CONTROLLER standard/advanced
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 17
3 Device structure
3.1 MOVI-C® FIELD CONTROLLER Standard/Advanced
MOVI-C®
FIELD
CONTROLL
ER
standard/
advanced
The MOVI-C® FIELD CONTROLLER consists of a decentralized controller (referred to
as electronics cover in the following) and a connection box with field distributor func-
tionality.
76646 Bruchsal/Germany
MMF11S00-000-SFCDI0-C/DSP/IV/DFC20A-0020
01.1234567890.0001.14
LISTEDIND.
CONT.EQ.2D06
®
Eingang/Input
U =AC 3x380...500V
I =AC 1.9A
f =50...60Hz
T =-25°C...+40°C IP 54 ML0001 28108558
U =3x0...Uinput
I =AC 2.0A
f =0...599Hz
Ausgang/Output
[4]
[5]
[6]
[7]
[1]
[2]
[10]
[9]
[4]
[3]
[6]
[7]
[8]
[5]
9007227774420363
[1] LED displays
[2] M12 plug connector
[3] Switch disconnector (optional) with feedback contact (with triple lock, color: red/
black)
[4] Screws for PE connection
[5] Mounting lug
[6] M16 Cable glands
[7] M25 Cable glands
[8] Nameplate
[9] Connection box
[10] Decentralized controller (referred to as electronics cover in the following)
26872137/EN – 12/2021

3Device structure
Cable entry position
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
18
3.2 Cable entry position
3.2.1 MFC1.. design
The following cables entries are possible for the device:
• Position X + 2 + 3
– X: 2 × M25 × 1.5 + 2 × M16 × 1.5
– 2: 2 x M25 x 1.5 + 2 x M16 x 1.5 (only in MFC1.. design without switch dis-
connector)
– 3: 3 × M25 × 1.5 + 3 × M16 × 1.5
The following figure shows the possible cable entries:
3
X3 X
22
18014427029428747
26872137/EN – 12/2021

3
Device structure
Nameplate position
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced 19
3.3 Nameplate position
3.3.1 MFC1.. design
The following nameplate positions are possible for the device:
• Nameplate of the complete device: Position X
• Optional nameplate: Position 2
The following figure shows examples of the nameplate position:
X
76646Bruchsal/Germany
MMF11S00-000-SFCDI0-C/DSP/IV/DFC20A-0020
01.1234567890.0001.14
LISTEDIND.
CONT
.EQ.2D06
®
Eingang/Input
U =AC 3x380...500V
I =AC 1.9A
f =50...60Hz
T =-25°C...+40°C IP 54 ML0001 28108558
U =3x0...Uinput
I =AC 2.0A
f =0...599Hz
Ausgang/Output
76646 Bruchsal/Germany
MFC10-000-5X3-C/FHX
01.1234567890.0001.20
Eingang/Input
U = AC 3x380...500V
I = AC 24A
f = 50...60Hz
T = -30°C...+40°C IP 65 ML 0001 28122070
U = U input
I = I input
f = f input
Ausgang/Output
LISTED IND.
CONT.EQ.2D06
®
35620660235
3.4 Example nameplate and type designation
3.4.1 Nameplate
The following figure gives an example of a nameplate of the device. For the structure
of the type designation, refer to chapter "Type designation".
76646 Bruchsal/Germany
MFC10-000-5X3-C/FHX
01.1234567890.0001.20
Eingang/Input
U = AC 3x380...500V
I = AC 24A
f = 50...60Hz
T = -30°C...+40°C IP 65 ML 0001 28122070
U = U input
I = I input
f = f input
Ausgang/Output
[2]
[1]
LISTED IND.
CONT.EQ.2D06
®
35620657163
[1] Product label with QR code. The QR code can be scanned. You will
be redirected to the digital services of SEW‑EURODRIVE. There, you
have access to product-specific data, documents, and further ser-
vices.
[2] Unique serial number
26872137/EN – 12/2021

3Device structure
Example nameplate and type designation
Operating Instructions – MOVI-C® FIELD CONTROLLER standard/advanced
20
3.4.2 Type designation
The following table shows the type designation of the MOVI-C® FIELD CONTROLLER
standard/advanced:
MFC Product family
MFC = MOVI-C® FIELD CONTROLLER
1 Variant
1= Device variant1 for EtherCAT®/SBusPLUS devices
0 Front module
0= Closed
–
000 Switch disconnector
000=Without switching element
D01= Switch disconnector with feedback contact without line protection
–
5 Power connection
5= 380–500Vac
X Interference suppression
X=Without basic interference suppression
3 Connection type
3= 3-phase
–
C Version
/
FHX Electronics cover (controller) design
See chapter "Type designation of the electronics cover (controller)"
/
IV Options
IV= Plug connector
PE=Pressure compensation fitting
26872137/EN – 12/2021