Sharp RZ-X650 User manual

MSR USER GUIDE
POS TERMINAL MODEL RZ-
X
650
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are sub
j
ect to chan
g
e without notice.

Contents
1. MSR operations type options………………………………………….… 1
2. Installing the Keyboard Interface re-director…………………………. 1
3. Enabling the MSR keyboard mode……………………………………… 3
4. Disabling the MSR keyboard mode (for Setter configuration)…….. 4
5. MSR Keyboard settings…………………………………………………… 5
6. MSR keyboard operation verification…………………………………… 6
7. MSR Setter utility (Swipe format configuration)………………………. 8

RZ-X650 MSR User Guide
1 SHARP
1. MSR operations type options
The RZ-X650 Magnetic Card Reader (MSR) supports several operation modes to provide a range
of connection methods for software applications.
•Serial device (default)
•OPOS driver (default)
•Keyboard interface device
2. Installing the Keyboard Interface re-director
To use the Keyboard interface for MSR output you must install and activate the MSR2KBD re-
director.
1. Double touch the SetupMSR2KBD shortcut on the desktop
2. Choose NEXT

RZ-X650 MSR User Guide
2 SHARP
3. Select INSTALL
4. Touch FINISH

RZ-X650 MSR User Guide
3 SHARP
3. Enabling the MSR keyboard mode
If the MSR_KBD utility has been removed and is required follow these steps:
1. Touch the windows [Start] button
2. Select Programs
3. Select the MSR-KBD folder
4. Select MSR_KBD program
5. Check the box “Start this application when Windows starts”.
6. Touch the [Start Redirecting] button, Keyboard interface mode is now enabled.

RZ-X650 MSR User Guide
4 SHARP
4. Disabling the MSR keyboard mode (for OPOS / Serial use)
To temporarily disable the keyboard interface mode (example: to make configuration changes)
follow these steps:
1. Touch the MSR_KBD icon and hold for approximately 2 seconds
2. Touch the checkmark on Redirecting(R) to uncheck the keyboard mode.
3. Notice the icon is now grayed out
4. To re-enable to keyboard mode again touch the MSR_KBD icon and touch the
Redirecting(R) to re-check the keyboard mode
To permanently disable the keyboard interface mode (example: to use the MSR in Serial or
OPOS mode) follow these steps:
1. Touch the MSR-KBD icon
2. Touch Setting(S) to open the MSR-KBD settings
3. Uncheck the box “Start this application when Windows starts”

RZ-X650 MSR User Guide
5 SHARP
4. Close the settings window
5. Reboot the unit
6. The MSR-KBD icon should not be visible now
5. MSR Keyboard settings
The MSR_KBD program contains settings for the direct interface to the MSR device.
1. Touch the MSR-KBD icon
2. Touch Setting(S) to open the MSR-KBD settings
3. Touch [Change Settings] button

RZ-X650 MSR User Guide
6 SHARP
4. Available settings include:
a. Com Port Default = COM5
b. Baud Rate Default = 19200
c. Data Bit Fixed at 8
d. Parity Bit Fixed at N
e. Stop Bit Fixed at 1
f. Hand Shaking Default = None
g. [Default] returns all settings to original values
h. [OK] to save changes
i. [Cancel] to exit without saving changes
6. MSR keyboard operation verification
You can test the MSR_KBD mode output when swiping a card.
1. Touch the windows [Start] button
2. Select Programs
3. Select Accessories
4. Select Notepad
5. Swipe the card in the MSR
The Magnetic Stripe Data from the card should display in Notepad

RZ-X650 MSR User Guide
7 SHARP

RZ-X650 MSR User Guide
8 SHARP
7. MSR Setter Utility (Swipe format configuration)
The MSR Setter is used to select and configure what data is received by the POS terminal.
A. Starting MSR Setter utility
1. Touch the windows [Start] button
2. Select Programs
3. Select MSR Setter