Shelters4Less SR1583 User manual

Assembly Instructions
Product Code: SR1583
Doc. No.: SR1583-01-250117-S4L
[email protected]
www.shelters4less.co.uk
0800 160 1002

14
15
8
8
12
12
5
16
10
999
3
7
2
1
1111111111
33
7
4
6
2
Spanners
Torx bit
Tools required:
Drill/Screwdriver
Mallet
Hack saw
EXPLODED VIEW

3
PARTS LIST
Fittings T25
M10 x 60 M10 Nut M10 Washer Black Cap
25mm Tech
screw
100mm Concrete
Anchor Bolt
Quantity 22 22 44 44 100 5
Image
ITEM
NO.
PART
NO.
DESCRIPTION DIMENSIONS (mm) IMAGE QTY.
1
S3(M3)
Frame
2000 X 517
1
2
S1
Frame
2000 X 1035
2
3
CB1
Bracket
110 x 110 x 40
4
4
JF1
Bracket
220 x 40
2
5
S3(4)
Frame
2000 X 517
1
6
L3
L3 Bracket
95 X 45
2
7
RB2
Bracket
110 X 45
4
8
R3
Rafter
1030 3
9
L1
L1 Bracket
95 X 45
4
10
B2
B2 Beam
2100 1
11
FT1
Bracket
109 x 100 x 3
5
12
SS
Sealing Strip
1070 (CUT TO LENGTH)
12
14
RC3
Roof Strip
1070 X 60
3
15
ACE3
Roof Sheet
1070 X 1050
2
16
A1
Roof Angle
50 x 50
2100 LONG
1
17
EC40
Plastic
End Cap
40 X 40
10

557
2110
517
CB1CB1
CB1
CB1
JF1JF1
S1
S1
S3
S3
Plastic
End
Cap
Plastic
End
Cap
Plastic
End
Cap
Plastic
End
Cap
IMPORTANT:
Check overall dimensions
for correct alignment
TOP VIEW
Ensure correct alignment on both sideEnsure correct alignment on both side
Step 1
Assemble all the Frames (S1 & S3) to make up the main structure using
CB1 Brackets in the corners and JF1 Brackets in the center.
Push in the Plastic End Caps only where indicated below (not along
the back of the shelter)
4
General Note:
The 50mm Tech Screws are
for fixing roof strips only
(RC1 - step5)

RB2
RB2
L3
L3
R3
R3
RB2
RB2
L3
L3
R3
R3
Step 2
Attach the outer Rafters (R3) using RB2 Brackets at the rear and
L3 Brackets in the middle of the rafters.
5

L1
L1
L1
B2
L1 L1L1 L1
B2
Step 3
Attach four L1 Brackets to the B2 Beam . Then attach it to the front of the
Rafters.
6

R3
RB2RB2
FT1FT1FT1FT1FT1
R3
FT1FT1FT1
Step 4
Fix the central Rafter (R3) to the front first then use RB2 Brackets to
secure it at the back. Attach the FT1 Brackets to the bottom of the
shelter, then move the structure to its final position and make sure
everything is square before bolting it to the ground.
7

SSSSSS
SS
SS
SS
ACE3
ACE3
X
SS
SS
Ace 3
ACE3
DETAIL X
SCALE 1 : 1
B2 Beam
SSSS
SSSS
ACE3
Tech
Screw
Step 5
Stick two Sealing Strips (SS) to each Rafter Leaving a gap between them
for the Tech screws (As shown in Detail X below). Place the ACE3 Roof
Sheets on top and screw them into place. Stick six more pieces of Sealing
Strips (SS) on top of the roof sheets leaving the same gap.
8

RC3
RC3
RC3
A1
A1
RC3RC3
RC3
Step 6
Line up the Roof Strips (RC3) on top of the sealing strips and secure
them using 50mm tech screws. Attach the Angel (A1) to the back of the
shelter and push plastic caps on any exposed nuts and bolts
to complete the installation.
9

2110
1081
420 110
67 1035 935
477 99 506
10
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 200mm oversized on all four sides

NOTES:
11

12
CONTACT DETAILS:
Email : [email protected]
Web : www.shelters4less.co.uk
Tel : [phone]
Shelters4Less, Unit 3, 2 Lansdowne Crescent, Bournemouth, BH1 1SA
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
All Parts and Fixings checked by:
Print Name: Signature: