Shelters4Less SR1586 User manual

Assembly Instructions
Shelter Type: SR1586
SR1586-01-180717-UK
Email : [email protected]
Web : www.shelters4less.com
Tel : [phone]

1
2
13
6
5
12
10
7
11
4
8
9
3
14
3
16
2
EXPLODED VIEW

3
PARTS LIST AND FIXINGS
ITEM NO.
PART NO. Description DIMENSION IMAGE QTY.
1 S1 FRAME 2000 x 1035 4
2 CB1 BRACKET 110 x 110 6
3 JF1 BRACKET 220 x 40 4
4 Bracket BRACKET 110 x 46 4
5
NBBS S1 STUB 145 x 40 x 40
2
6
JF2 BRACKET 130 x 30 x 3
4
7
R5
CURVED
RAFTER
2159 x 40 x 40
1
8
R4
CURVED
RAFTER
2159 x 40 x 40
2
9
ST8 ROOF TIE 2110 x 40 x 40
1
10 L1 BRACKET 95 x 45 4
11
SS SEALING STRIP Trim to Length
4
12 ACE2 ROOF PANEL 2210 x 1050 2
13 RC2 ROOF STRIP cut to suit 3
14 FT1 FOOT BRACKET 109 x 100 5
15 EC40
PLASTIC
END CAP
16 A1 ANGLE
2100 1
FIXINGS Bolt set M10
Nut Washer
Black
Cap
T25 T50 AB1210
M10 x 60mm
25mm
Tech
screw
50mm
Tech
screw
M10 X 100mm
Concrete Bolt
Pack A
30 30 60 60 72 30 8
Required 24 24 48 48 52 30 5
Spare
6 6 12 12 20 0 3
Image
40 x 40 10

1035
2110
Step 1
Assemble S1 frames to make up the main structure using
CB1 brackets in the corners and JF1 brackets for the straight joints.
S1
S1
S1
S1
CB1
CB1
JF1
Please note 50mm Tec Screws
are for roof panels only
Ensure correct
alignment
on both sides
JF1 CB1CB1
S1
S1
S1S1
4
check shelter dimensions
to ensure correct alignment

R5
R5
R4
JF2
JF2
SB1 Stub
S1 Stub
CB1
RB2RB2
RB2
RB2
5
L1
L1
L1
L1
ST8
FT1
FT1
FT1
FT1
CB1
JF2
JF2
JF1
SB1
Step 2
Attach JF2 brackets to SB1 Stubs. Using CB1 and JF1 brackets secure SB1
to frame. Now fix the RB2 brackets to the rear of the frame,
attach R4 & R5 rafters. Use L1 brackets to attach ST8 tie bar.
Move the shelter in to its final position, make sure its square and attach
FT1 foot brackets. Use the anchor bolts to secure it to the ground.

ACE2
ACE2
SEALING STRIP
SEALING STRIP
ACE2
Step 3
Apply sealing strips to rafters. Align the two ACE2 roof panels with
the outer edges of the shelter, leaving a gap in between the
panels.
6

RC2
Sealing
Strip
A1
RC2
Sealing
Strip
7
Step 4
Apply sealing strips to the top of the panel and use RC2 strips to
cover the gap in the centre and the edges. Finish of the shelter by
attaching the A1 angle trim.
Finally fit the Black
plastic caps on exposed
nuts and bolts, and fit the
square end caps to any
open ends of box
sections.

989 1095
989
1052
113
2119
Plan View
Suggested size for concrete base: 200mm oversized on all four sides
8
2209

Notes
:
9

Notes
:
10

Notes
:
11

12
CONTACT DETAILS:
Email : [email protected]
Web : www.shelters4less.co.uk
Tel : [phone]
Unit 3, 2 Lansdowne Crescent, Bournemouth, BH1 1SA
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big •
storm)
Touch up any exposed metal should it get scratched •
All Parts and Fixings checked by:
Print Name: Signature: