Shelters4Less SR4500-01-16012017-S4L User manual

Assembly Instructions
Shelter type: Canterbury 4m
SR4500-01-16012017-S4L
0800 160 1002
[email protected]
www.shelters4less.co.uk

3
9
5
2
9
4
7
8
3
66
5
5
4
9
9
10 9
9
2
11
11
Optional
Extra
Optional
Extra
2
Tools required: (Not supplied)
Drill/Screwdriver
Socket set

3
PARTS LIST & FITTINGS
Fittings
M10 x 20
Hex head
bolt
M10 x 70
x 80
Hex head
bolt
M10 x 100
Anchor
bolt
M10
Nuts
M10
Standard
Washers
M12
Standard
Washers
25mm
Tech
screws
Plastic
caps M10
QTY.
28 8 / 46 12 52 6 120 52
Image
ITEM
NO.
PART
NO.
DESCRIPTION DIMENSION (mm) IMAGE QTY.
1
EC50
Plastic end cap
50 x 50
2
2
KFF
Kimmeridge Front Frame Assembly
1975 x 990
2
3
KRF
Kimmeridge Rear Frame Assembly
2115 x 985
2
4
KST
Kimmeridge Straight Tie Bar Assembly
1535 2
5
CTB
Central Tie Bar
1950 4
6
FTT Front Top Tie 1975 2
7
TCC
Centre Curve (2 Parts)
1330 1
8
LCC
Lower Centre Curve
1580 1
9
KIF
Kimmeridge Internal Foot
153 6
10
CP
Centre post
1975 1
11
RP1
Roof Panel
2970 x 2015
2

KFF
KRF
KST
Left End Frame
COMPLETE FRAME (CF)
CTB
CTB
FTT
Step 1
4
If you have received the "Split End" version (If not go straight to Step 1)
Take the CF Side Frame and attach the CTB Tie Bar to it in the positions
shown below. Now secure the FTT Fron Top Tie to the Side of the
shelter using M10 Bolts supplied.
2 people recommended
to fit this shelter.
Note: Shelter ends have 2 sides Left and Right. Make
sure all holes are in correct position before assembling.
Join the three frame sections to make the Complete Side Frame using M10
bolts.

Loosely fasten TCC Top Centre Curve to CTB Central Tie Bar , after
doing this place CP Central Post under FTT Front Top Tie and bolt
through all 3 parts.
TCC
CP
CTB
FTT
Put the LCC Lower Centre Curve in place do not tighten the bolts to
far as the second side will be attached here.
LCC
Step 2
5
Step 3

CTB
CTB
CF
FTT
CP
LCC
TCC
Side Panel
are added
extras.
RP1
RP1
6
Step 5
Offer each panel to the shelter as shown below and secure in place using
Tec-Screws. (1 Screw every 8 inches)
Step 4
Repeat Step 1, 2 and 3 with the opposite side of the shelter this time
securing all centre bolts tightly making one complete unit.
Always clean off swarf when
fitting the roof panels to
avoid rust stains.

KIF
KIF
KIF
KIF
KIF
KIF
Don't forget to add Plastic End
Caps to shelter before finishing.
Note: Minimum of 2 people to
move shelter into position.
7
Step 6
Finally move shelter to desired position and instert KIF Kimmeridge Internal
Foot into each leg. (Note: the extra holes withing the foot is to allow
adjustment on an uneven surface) Secure in Place using the Anchor Bolts
supplied.

8
THANK YOU
FOR PURCHASING THIS PRODUCT
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
CONTACT DETAILS:
Email : [email protected]
Web : www.shelters4less.co.uk
Tel : [phone]
Shelters4Less, Unit 3, 2 Landsdowne Crescent, Bournemouth, BH1 1SA
All Parts and Fixings checked by:
Print Name: Signature: