Skoda iV Charger User manual

ŠKODA iV
Charger
Charger Connect
Charger Connect+
EN
ES
PL
EL
Manual |Part A

EN This charging station (wallbox) is exclusively designated for charging Škoda passenger vehicles.
Information on technical specifications, design, equipment, materials, warranties and exterior design
relate to the period when the assembly manual is being submitted to print. The manufacturer reserves
the right to make changes (including changes to technical parameters related to innovations).
ES See laadimisjaam (wallbox) on ettenähtud eksklusiivselt Škoda sõiduautode laadimiseks.
Tehnilisi andmeid, tehnilist lahendust, varustatust, materjale, garantiisid ja väliskujustust puudutav teave
vastab juhendi trükki andmise ajale. Tootja jätab enesele õiguse teha muudatusi (sh innovatsiooniga se-
otud muudatusi tehnilistesse parameetritesse).
PL Ta stacja ładowania (wallbox) została zaprojektowana wyłącznie do ładowania samochodów
osobowych Škoda.
Informacje dotyczące specyfikacji technicznych, designu, wyposażenia, materiałów, gwarancji i desig-
nu zewnętrznego dotyczą okresu, kiedy instrukcja montażu została przesłana do druku. Producent
zastrzega sobie prawo do dokonywania zmian (także zmian w parametrach technicznych związanych
z innowacjami).
EL Αυτός ο σταθμός φόρτισης (κουτί τοίχου) προορίζεται αποκλειστικά για φόρτιση επιβατικών
οχημάτων Škoda.
Οι πληροφορίες σχετικά με τις τεχνικές προδιαγραφές, τον σχεδιασμό, τον εξοπλισμό, τα υλικά, τις
εγγυήσεις και τον εξωτερικό σχεδιασμό συνδέονται με τη χρονική περίοδο κατά την οποία υποβλήθηκε
προς εκτύπωση το εγχειρίδιο συναρμολόγησης. Ο κατασκευαστής επιφυλάσσεται του δικαιώματός του
να πραγματοποιεί αλλαγές (περιλαμβανομένων αλλαγών σε τεχνικές παραμέτρους που σχετίζονται με
καινοτομίες).

ŠKODA iV
Charger
Charger Connect
Charger Connect+
Manual |Part A
EN

EN
7
CONTENTS
1. General information and scope............................................................................................. 8
1.1 Scope of the document ...................................................................................................................8
1.2 General ...................................................................................................................................................8
1.3 Safety precautions..............................................................................................................................8
1.4 Technical specifications.................................................................................................................. 13
2. Product information .................................................................................................................15
3. Charge with the wallbox .........................................................................................................16
3.1 Start and stop a charging session ..............................................................................................16
3.2 Status indication............................................................................................................................... 17
4. Prepare for installation............................................................................................................21
4.1 Content of delivery .........................................................................................................................21
4.2 Prerequisites for installation ....................................................................................................... 22
4.3 Tools and material needed........................................................................................................... 24
4.4 Notice on installation..................................................................................................................... 26
5. Install wallbox ............................................................................................................................28
5.1 Install wall bracket.......................................................................................................................... 29
5.2 Prepare main assembly for installation...................................................................................30
5.3 Mount main assembly onto wall bracket................................................................................ 31
5.4 Assemble wallbox........................................................................................................................... 32
6. Set DIP-switches ......................................................................................................................36
7. Configure ŠKODA iVCharger Connect and ŠKODA iVCharger Connect+.........42
7.1 Privacy information......................................................................................................................... 42
7.2 Configure the ŠKODA iVCharger Connect and ŠKODA iVCharger
Connect+ locally.............................................................................................................................. 45
7.3 Pair ŠKODA iV Charger Connect and ŠKODA iV Charger Connect+ to
ŠKODA account.............................................................................................................................. 46
8. Commissioning.......................................................................................................................... 47
9. Maintenance...............................................................................................................................47
10. Troubleshooting ........................................................................................................................48
10.1 Error states of the wallbox........................................................................................................ 48
10.2 Adjust the length of the charging cable............................................................................... 54
11. Decommissioning.....................................................................................................................55
12. Disposal........................................................................................................................................55
13. Appendix......................................................................................................................................56
13.1 Warranty........................................................................................................................................... 56
13.2 EU Declaration of conformity .................................................................................................. 56
13.3 Glossary.............................................................................................................................................57

EN
8
1. GENERAL INFORMATION AND SCOPE
1.1 Scope of the document
Keep this manual for the entire life cycle of the product.
The following installation-related and troubleshooting chapters are intended for qualified
personnel, such as certified electricians, who can correctly and safely install the wallbox and
identify potential danger:
- Chapters: 1, 4, 5, 6, 8, 9, 10, 11 and 12.
The following usage-related chapters are intended for end-users to correctly and safely op-
erate the wallbox:
- Chapters: 1, 2, 3, 7 and 13.
Legal information
© 2020 EVBox Manufacturing B.V. - all rights reserved. Nothing from this document may
be modified, reproduced, processed, or distributed in any form or by any means, without the
prior written permission of EVBox.
1.2 General
Product and environmental characteristics
The charging station has been CE-certified by the manufacturer and
bears the CE logo. The relevant declaration of conformity may be
obtained from the manufacturer.
The charging station complies with the RoHS Directive (RL
2011/65/EU). The relevant declaration of conformity may be
obtained from the manufacturer.
Electrical and electronic appliances, including accessories, must be
disposed of separately from the general municipal solid waste.
Recycling of materials saves raw materials and energy and makes a
major contribution to conserving the environment.
1.3 Safety precautions
Read and obey the following safety precautions before you install, service or use your charg-
ing station. A qualifi
ed electrician must ensure that the charging station is installed in accord-
ance with the relevant country-specific standards and local regulations.

EN
9
Symbols
The symbols used in this manual have the following meaning:
Symbols used and their explanations
B5.1
This symbol indicates that the illustrations corresponding to the
indicated chapter are to be found in manual B.
1., a. or I. Actions to be followed in the stated order.
-Actions to be followed in a non-specific order.
Note: Texts with this symbol contain supplementary information.
Highlighted sections
Danger
Texts with this symbol contain information regarding hazardous situations which
will cause death or severe injures if ignored.
Warning
Texts with this symbol contain information regarding hazardous situations which
could cause death or severe injuries if ignored.
Caution
Texts with this symbol contain information regarding hazardous situations which
could cause minor or moderate injuries if ignored.

EN
10
The following sections contain general information that applies when installing and
using the wallbox.
Danger
Operating the wallbox when it indicates an error state, or when the wallbox or the charg-
ing cable have cracks, show extensive wear, or other physical damage, will result in the
risk of electric shock, which will cause severe injuries or death.
▶ Do not operate the wallbox if it is physically damaged.
▶ In the event of danger and/or an accident, a certified electrician must immediately
disconnect the electrical supply from the wallbox.
▶ See chapter Troubleshooting for explanation and further instructions on indicated
error states.
▶ Contact [e-mail] or your distributor if you suspect that the wallbox
or cable is damaged.
Some electric vehicles release hazardous or explosive gasses when charging which will
result in the risk of explosion, and thus cause severe injuries or death.
▶ Refer to your vehicle user manual to check if your vehicle releases hazardous or
explosive gases when charging.
▶ Follow the instructions given in the vehicle user manual before choosing the location
of the charging station.
Extensive exposure of the wallbox to water or handling the wallbox with wet hands will
result in the risk of electric shock, which will cause severe injuries or death.
▶ Do not direct powerful jets of water toward or onto the wallbox.
▶ Never operate the wallbox with wet hands.
▶ Do not put the charging plug into any liquid.
Not following the installation instructions given in this manual will result in the risk of
electric shock to users, which will cause severe injuries or death.
▶ Read this manual before installing the wallbox.
▶ If you are unsure about how to use the wallbox after reading this manual, ask for
help at [e-mail] or visit your local dealer for more information.
▶ Do not allow children to operate the wallbox. Adult supervision is required when
children are near a wallbox that is in use.
Servicing of the wallbox or its components by non-qualified personnel will result in the
risk of electric shock and damage to the wallbox, which will cause severe injury or death.
▶ The user must not attempt to service or repair the wallbox as it does not contain
user-serviceable parts.
▶ The wallbox must only be serviced, repaired or relocated by a qualified electrician.

EN
11
Warning
Improper usage of the wallbox may result in damage to the wallbox, which may cause
injury or death.
▶ Read this manual before using the wallbox.
▶ If you are unsure about how to use the wallbox after reading this manual, ask for
help at [e-mail] or visit your local dealer for more information.
▶ Do not allow children to operate the wallbox. Adult supervision is required when
children are near a wallbox that is in use.
Using adapters, conversion adapters or cord extensions with the wallbox may result in
technical incompatibilities and can result in damage to the wallbox, and thus cause injuries
or death.
▶ Use this charging station to charge Mode 3 compatible electric vehicles only.
▶ Refer to your vehicle user manual to check if your vehicle is compatible.
Exposure of the wallbox to heat sources or flammable substances can result in damage to
the wallbox, and thus cause injuries or death.
▶ Make sure that the wallbox or the charging cable never come into direct contact
with heat sources.
▶ Do not use explosive or readily flammable substances near the wallbox.
Using the wallbox under conditions not specified in this manual may result in damage to
the wallbox, which may cause injury or death.
▶ Only use the wallbox under the specified operating conditions, see chapter Technical
specifications.

EN
12
Caution
Charging the electric vehicle with the charging cable not being completely unwound may
result in overheating of the cable, which can damage the wallbox.
▶ Make sure to completely unwind the charging cable and avoid overlapping loops
before charging your electric vehicle.
Putting fingers into or leaving other objects inside the plug port (for example during
cleaning) may cause injury or damage to the wallbox.
▶ Do not put your fingers into the plug port.
▶ Do not leave objects inside the plug port.
Use of devices with (electro) magnetic properties in the vicinity of the wallbox may cause
damage to the wallbox and affect its operation.
▶ Keep and use (electro) magnetic devices a safe distance from the wallbox.
Transport and storage
▶ Disconnect input power before removing the charging station for storage or relocation.
▶ Only transport and store the charging station in its original packaging. No liability can
be accepted for damage incurred when the product is not transported in its original
packaging.
▶ Store the charging station in a dry environment in the temperature range given in the
specifications.

EN
13
1.4 Technical specifications
Feature Description
Electrical properties
Connection capacity 1-phase, 230 V, 32 A, 50 Hz.
3-phase, 400 V, 16 A, 50 Hz.
Charging capacity 7.4 kW (1-phase - 32 A).
11 kW (3-phase - 16 A).
Charge mode Mode 3 (IEC 61851) - ISO 15118*.
Fixed charging cable Type 2 plug (IEC 62196-2).
Number of fixed charging cables 1.
Charging cable length 4.5 m or 7.5 m.
Installation wiring 16 A installation input terminals: 1 - 6 mm².
32 A installation input terminals: 1 - 10 mm².
Metering Optional, for ŠKODA iVCharger Connect+.
Safety and certification
Upstream installation
protection
Minimum dedicated 1-phase 32 A (32 A station) or
3-phase 16 A (16 A station) upstream circuit breaker
and at minimum RCD type A (30 mA AC). Check local
installation requirements if additional measures are
required.
Static power limitation Via DIP-switches.
Earth leakage sensor (ELS) 6 mA DC.
Ground loss monitor Physical connection m quality monitoring, without
ground monitoring
Black-out protection Via CT coils - optional comfort feature.
CT colis supported
Invasive / non-Invasive - 40 A - 200 A,
brands:VAC, LEM, and Nidec.
See chapter Set DIP-switches for the supported
models.
Operating temperature range -30 °C - +50 °C.
Storage temperature range -30 °C - +85 °C.
Operating humidity Max. 95 % - non-condensing.
Maximum installation height Max. 4000 m above sea level.
Enclosure ratings IP54 (IEC 60529), IK10 (IEC 62262).
Certification See EU Declaration of conformity
*For ŠKODA iVCharger Connect and ŠKO
D A iV Charger Connect+ only.

EN
14
Feature Description
Safety Class
Safety Class I (the charging station is equipped with a
ground terminal for safety) and overvoltage Category
III.
Power supply input EV Supply equipment permanently connected to AC
supply network.
Normal Environmental
conditions
Outdoor use.
Access Equipment for locations with non-restricted access.
Connectivity
Authorization* NFC / RFID (ISO 14443, ISO 15693).
Plug & Charge (ISO 15118).
Status indication / HMI (Human
Machine Interface)
LED based HMI.
Communication standard* Wi-Fi 2.4 / 5 GHz, Ethernet (via RJ45 connection),
optional 4G / LTE.
Communication protocol to
backend*
OCPP 2.0J.
Communication protocol to
Home Energy Management
System*
EEBus.
Local configuration* via Configuration Manager.
Physical properties
Housing Polycarbonate.
Front panel Polycarbonate and hardened glass.
Bezel Acrylonitrile Styrene Acrylate (ASA).
Mounting bracket Steel (zinc plated).
Dimensions (W x H x D) 297 mm x 406 mm x 116 mm.
Weight
▶ 1-phase 32 A station with 4.5 m charging cable
~ 6kg.
▶ 1-phase 32 A station with 7.5 m charging cable
~7 kg.
▶ 3-phase 16 A station with 4.5 m charging cable
~ 6 kg.
▶ 3-phase 16 A station with 7.5 m charging cable
~ 7 kg.
Mounting method
Stationary equipment, mounted on walls (preferred
method), poles or equivalent positions – surface
mounted.
Color Platinum gray with electric white bezel.
*For ŠKODA iVCharger Connect and ŠKO
D A iV Charger Connect+ only.

EN
15
Features ŠKODA iV
Charger
ŠKODA iV
Charger
Connect
ŠKODA iV
Charger
Connect+
Maximum output power 7.4 kW (1-phase)
Maximum output power 11 kW (3-phase)
Attached charging cable Type 2 (4.5 m or
7.5 m)
Alternating Current (AC) charging
Integrated Direct Current (DC) fault current
detection
Wi-Fi / Ethernet communication
LTE mobile network communication *
Data transfer according to OCPP 2.0J
Access control with charge card
Remote access via MyŠKODA Powerpass
app
Remote software update / diagnostic
MID certified power consumption recording
and calculation
The table below contains the available product configurations for the ŠKODA iV Charger
models.
2. PRODUCT INFORMATION
* Option

EN
16
3.1 Start and stop a charging session
* For ŠKODA iVCharger Connect and ŠKODA iV Charger Connect+ only.
3. CHARGE WITH THE WALLBOX
Warning
Using a damaged wallbox or a damaged charging cable may expose the user to electric
components and result in the risk of electric shock, which may cause injury or death.
▶ Always check that the wallbox, the charging cable, and the charging plug are free of
damage before starting a charging session.
▶ Always check that the contact area of the charging plug is free from dirt and
moisture before starting a charging session.
▶ Make sure that the charging cable cannot become damaged (kinked, jammed or
driven over).
▶ Take precautions so that the charge plug does not come into contact with heat
sources, dirt or water.
1. Start charging
– Plug the charging cable into your car.
– Optionally, hold your charge card (RFID card) in front
of the reader on the charging station to start charg-
ing.*
3. Stop charging.
– Optionally, hold your charge card (RFID card) in front
of the reader on the charging station to stop charg-
ing.*
– Unplug the charging cable from your car.
2. Your car is charging.

EN
17
Off or energy saving
Wallbox is starting up.
Wait until the wallbox is
ready to charge.*
* For ŠKODA iVCharger Connect and ŠKO
D A iV Charger Connect+ only.
1 2
4
3 5 6
8
7
DisplayState description
LED description LED states
3.2 Status indication
1Wallbox state
2Vehicle state
3House state
4RFID state
5Solid LED
6Flashing LED
7State remains unchanged
8O ff

EN
18
Configuration Manager
accessible via Wi-Fi
hotspot. Be aware that
charging is not possible
during this state.*
Idle - ready to charge.
Car plugged in,
charging paused
by wallbox, App, or
infrastructure. The
charging session
will continue when
allowed.
Car plugged in, not
charging, car paused /
fully charged.
DisplayState description
* For ŠKODA iVCharger Connect and ŠKO
D A iV Charger Connect+ only.

EN
19
Car plugged in, waiting
for charge card/
NFC input or remote
authorization.*
Car plugged in,
charge card/NFC
authorization pending.*
Authorization
/ Remote Start
accepted.*
Car plugged in, charge
card/NFC rejected.*
DisplayState description
* For ŠKODA iVCharger Connect and ŠKO
D A iV Charger Connect+ only.

EN
20
Plug & Charge
authorization pending.*
Plug & Charge
authorization
rejected.*
Car plugged in,
charging.
DisplayState description
*For ŠKODA iVCharger Connect and ŠKO
D A iV Charger Connect+ only.
NOTE: If the wallbox shows other states than the ones described above, see Error states of
the wallbox for more information.