Solplanet ASW 3-6K S G2 Series User manual

ASW3000-S-G2/ASW3680-S-G2/ASW4000-S-G2
ASW5000-S-G2/ASW6000-S-G2
Quick Installation Guide
Android ios

The product is a transformerless PV inverter which converts the direct current of
the PV generator into grid-compatible single-phase alternating current and then
feeds the single-phase alternating current into the public power grid.
The product is intended for indoor and outdoor applications.
The product must only be connected with PV modules of protection class II (in
accordance with IEC 61730, application class A). PV modules with a high capaci-
tance to ground must only be used if their capacity does not exceed 1μF. Do not
connect any sources of energy other than PV modules to the product.
The product is not equipped with an integrated transformer and therefore has no
galvanic isolation. The product must not be operated with PV modules whose
outputs are grounded. This can cause the product to be destroyed. The product
may be operated with PV modules whose frame is grounded.
All components must remain within their permitted operating ranges and their
installation requirements at all times.
Use the product only in accordance with the information provided in the operating
instructions and with the locally applicable standards and directives. Any other
application may cause personal injury or property damage.
GENERAL INFORMATION
1
SAFETY
2
This quick installation guide does not replace the description in the comprehensive
operating instructions.
The contents of this guide may be updated or revised due to product development.
The information in this guide is subject to change without notice. The latest version
of this document and the comprehensive manual for installation, commissioning,
conguration and decommissioning are to be found in PDF format at www.solplan-
et.net.
2.1 INTENDED USE
1

2.2 IMPORTANT SAFETY INSTRUCTIONS
The product has been designed and tested strictly according to the international
safety requirements. As with all electrical or electronical devices, there are residual
risks despite careful construction. To prevent personal injury and property damage
and to ensure long-term operation of the product, read this section carefully and
observe all safety information at all times.
DANGER
！
Danger to life due to high voltages of the PV array
When exposed to sunlight, the PV array generates dangerous DC voltage
which is present in the DC conductors and the live components of the prod-
uct. Touching the DC conductors or the live components can lead to lethal
electric shocks. If you disconnect the DC connectors from the product under
load, an electric arc may occur leading to electric shock and burns.
• Do not touch non-insulated cable ends.
• Do not touch the DC conductors.
• Do not touch any live components of the product.
• Do not open the product.
• All work on the product must only be carried out by qualied personnel who
have read and fully understood all safety information contained in this docu-
ment and the operating instructions.
• Disconnect the product from voltage sources and ensure it cannot be
reconnected before working on the product.
• Wear suitable personal protective equipment for all work on the product.
The product must only be used in countries for which it is approved or released by
AISWEI and the grid operator.
The type label must be permanently attached to the product and must be in legible
condition.
This document does not replace any regional, state, provincial, federal or national
laws, regulations or standards that apply to the installation, electrical safety and
use of the product.
2

DANGER
！
Danger to life due to electric shock when touching live system
components in case of a ground fault
If a ground fault occurs, parts of the system may still be live. Touching live
parts and cables results in death or lethal injuries due to electric shock.
• Disconnect the product from voltage sources and ensure it cannot be
reconnected before working on the device.
• Only touch the cables of the PV modules on their insulation.
• Do not touch any parts of the substructure or frame of the PV array.
• Do not connect PV strings with ground faults to the product.
WARNING
！
Danger to life due to electric shock from destruction of the mea-
suring device due to overvoltage
Overvoltage can damage a measuring device and result in voltage being
present in the enclosure of the measuring device. Touching the live enclosure
of the measuring device results in death or lethal injuries due to electric shock.
• Only use measuring devices with a DC input voltage range of or higher.
CAUTION
！
Risk of burns due to hot enclosure parts
Some parts of the enclosure can get hot during operation.
• During operation, do not touch any parts other than the enclosure lid of the
product.
CAUTION
！
Risk of injury due to weight of product
Injuries may result if the product is lifted incorrectly or dropped while being
transported or mounted.
• Transport and lift the product carefully. Take the weight of the product into
account.
3

EU DECLARATION OF CONFORMITY
3
2.3 THE SARFTY SYMBOLS ON THE PRODUCT
within the scope of the EU directives
• Radio Equipment Directive 2014/53/EU
(L 153/62-106. May 22. 2014) (RED)
• Restriction of the use of certain hazardous substances 2011/65/EU
(L 174/88, June 8, 2011) and 2015/863/EU (L 137/10, March 31,2015) (RoHS)
confirms herewith that the products described in this document are in compliance
with the fundamental requirements and other relevant provisions of the above
mentioned directives. The entire EU Declaration of Conformity can be found at
www.solplanet.net.
Beware of a danger zone
This symbol indicates that the inverter must be additionally grounded if additional
grounding or equipotential bonding is required at the installation site.
Beware of high voltage and operating current
The inverter operates at high voltage and current. Work on the inverter must only be
carried out by skilled and authorized electricians.
Beware of hot surfaces
The inverter can get hot during operation. Avoid contact during operation.
Capacitor discharge
Danger to life due to high voltages in the inverter. Do not touch live parts for 5 minutes
after disconnection from the power sources.
Observe the documentation
Observe all documentation supplied with the product.
4

OVERVIEW
4
SCOPE OF DELIVERY
5
MOUNTING ENVIRONMENT
6
1 2 3 5
467
（1）DC SWITCH
（2）DC input
（3）COM1&COM2:RS485
（4）COM3:Meter
（5）COM4:WiFi/4G
（6）Connection point for an
additional grounding
（7）AC OUTPUT
inverter×1
wall bracket DC connector 2+2 AC connector ×1
document ×1
WiFi stick×1
mounting screw ×1
15°
×
√×
RS485 COM plug×1
(optional)
plug for meter ×1
(optional)
√ √ × ×
√× √ √ × ×
5

INVERTER'S MOUNTING
7
368
203
φ8
137
188
IP66
4K4H
-25℃
+60℃
≤100%
No touching
by children max.4000m
5
123
67
6
≥500mm
≥300mm
≥500mm
≥500mm
≥300mm ≥500mm
M5
2.5 Nm
4

SECOND PROTECTIVE GROUNDING
8
AC CONNECTION
9
1 2
M5
2.5 Nm
1
2
4
OK
5
123
3
6
7
1
2
3
10 to 14mm
53mm
13mm
6 to 8 mm² PE
LN
12±0.60mm

DC CONNECTION
10
4
OK
5
1 2 3
4
2.5-6mm2
Φ-5 8mm
≈12mm
click
OK
1
2.5-6mm2
Φ-5 8mm
8-10mm
23
5
6 8
6
7
8
1
2
√×
1
2
1
2
1
2
3
1
2
3
TYPE 1
TYPE 2

COMMUNICATION SETUP
11
11.1 COM1&COM2: RS485
2
1
11.2 COM3: Meter
Click
12
54
OK
3
❶
❷
RS485A
RS485B
6
9
1
2
3
5
4
Pin 1=TX_RS485A
Pin 2=TX_RS485B
Pin 3=NC
Pin 4=GND
Pin 5=NC
Pin 6=NC
Pin 7=NC
Pin 8=NC
Pin 1 Pin 8
8 7 6 5 4 3 2 1
3
46
OK
1
2
1
2
5

11.3 COM4：WiFi/4G
1
2
OK
2
1 2
45
3
×
10
√

CONTACT
12
EMEA
Service email: [e-mail]
APAC
Service email: [e-mail]
LATAM
Service email: service.LAT[email protected]
Aiswei Greater China
Service email: [e-mail]
Hotline: [phone]
Taiwan
Service email: [e-mail]
Hotline: [phone]
https://solplanet.net/contact-us/
To download the Solplanet app, please scan the appropriate QR code below.
ios
Scan QR code:
Android
Scan QR code:
11

AISWEI Technology(Shanghai) Co., Ltd.