Target Project 62 TGT42WD-DW User manual

>> Assembly instructions
TM
© 2021 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Deepwell Walled Desk with Drawer
Style #: TGT42WD-DW
DPC-item #: 249-14-5790

Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tool needed (only hex wrench included)
2
For tipping restraint hardware kit only.
Phillips head
screwdriver
Hex wrench

Children have died from furniture tipover.
To reduce the risk of furniture tipover:
⚫ ALWAYS install tipover restraint provided.
⚫ NEVER put a TV on this product.
⚫ NEVER allow children to stand, climb or hang
on drawers, doors, or shelves.
⚫ NEVER open more than one drawer at a time.
⚫ Place heaviest items in the lowest drawers.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
WARNING
3
Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
FURNITURE TIPPING RESTRAINT
YOUNG CHILDREN MAY BE INJURED BY TIPPING FURNITURE AND YOU MUST USE THIS TIPPING
RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.
TO PROVIDE PROTECTION AGAINST THE UNEXPECTED TIPPING OF
FURNITURE DUE TO IMPROPER USE.
USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE, THE RISK OF TIP-OVER.

M AX I M U M R E C O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 9.08 kg / 20 lb
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Deepwell Walled Desk with Drawer
MODEL # TGT42WD-DW
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE
WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE
INJURY.
4
MAXIMUM LOAD 4.54 kg / 10 lb
MAXIMUM LOAD 45.4 kg / 100 lb

5
hardware
Spare hardware
(H1) x 6
cam lock
(H2) x 6
cam bolt
(H3) x 13
M6 x 30 mm
wood dowel
(H8) x 1
Handle bolt
(H10) x 4
cam lock cover
(H12) x 1
tipping restraint
hardware kit (inside
plasticbag)
(H11) x 1
hex wrench
(H4) x 4
1/4” x 13 mm bolt
(H5) x 4
M4 x 13 mm
pan head screw
(H6) x 2
M4 x 25 mm
screw
(H7) x 24
M4 x 38 mm
screw
(H9) x 1
handle
(H13) x 4
1/4” x 27 mm bolt
(H14) x 4
lock washer
(H15) x 4
flat washer
(H16) x 1
grommet with cap
(H17) x 1
grommet
without cap

exploded diagram
6
ITEM DESCRIPTION QTY
ATop panel 1
BLeft side frame 1
CRight side frame 1
DFixed shelf 1
EBack panel 1
FDrawer box left side panel 1
GDrawer box right side panel 1
HDrawer box partition panel 1
IDrawer face 1
JDrawer front panel 1
KDrawer left side 1
LDrawer right side 1
MDrawer back panel 1
NDrawer bottom panel 1
ODrawer bottom support 1
O
D
H
I
B
G
F
C
A
E
J
K
L
M
N

how to use the cam lock system
1. 2. 3.
4. 5.
1. 2. 3.
Screw cam bolt into panel Push cam into panel - arrow
feature on cam top points to
panel edge
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
Rotate cam(s) clockwise
190°-230° to lock panels
together
Panels should be tight against
each other and connection
should be rigid
190°-230°
7

8
1.1. Attach drawer back panel (M) between the drawer side panels (K and L).
step 1: attach drawer back panel
(H7) x 4
M4 x 38 mm
screw
H7
M
H7
L
K
The grooves line up with
each other and face inward

9
2.1. Slide the drawer bottom panel (N) into the grooves between the drawer side panels (K and L) until fully inserted into the groove of the drawer back panel (M).
step 2: slide the drawer bottom panel
L
K
M
N

10
step 3: secure the drawer front panel to the drawer side panels
3.1. Secure the drawer front panel (J) to the drawer side panels (K and L) using four 38 mm screws (H7).
Note: Make sure that the drawer bottom panel (N) fits securely into the groove of the drawer front panel.
(H7) x 4
M4 x 38 mm
screw
H7
L
K
H7
J
N

11
step 4: fasten the drawer bottom support to drawer front and back panels
4.1. Fasten the drawer bottom support (O) to the drawer front and back panels (J and M) using four 38 mm screws (H7).
(H7) x 4
M4 x 38 mm
screw
H7
J
H7
M
O

12
step 5: attach drawer front panel to drawer face
5.1. Attach drawer front panel (J) to the drawer face (I) using two 25 mm screws (H6) as shown.
(H6) x 2
M4 x 25 mm
screw
I
H6
J
H6

13
step 6: Attach the handle
6.1. Fasten the handle (H9) to the front side of Drawer face (I).
(H8) x 1
Handle bolt
(H9) x 1
handle
H9
H8
I
J

14
step 7: Screw in the cam bolts
7.1. Securely screw the cam bolts into the designated small holes on the top panel (A).
(H2) x 6
cam bolt
H2
H2
H2
A
H2

(H1) x 6
cam lock
step 8: Attach the side panels and partition panel to the top panel
8.1. Attach the drawer box side panels (F and G) and the partition panel (H) to the top panel (A) using six cam locks (H1) and six wood dowels (H3) as shown.
15
(H3) x 6
M6 x 30 mm
wood dowel
F
G
H
H3
H1
H1
H1
A
H3
H3
The opening faces forward

16
step 9: attach fixed shelf to side panels and partition panel
9.1. Attach the fixed shelf (D) to the panels (F, G and H) using six 38 mm screws (H7) and three wood dowels (H3).
(H7) x 6
M4 x 38 mm
screw
(H3) x 3
M6 x 30 mm
wood dowel
H7
H3
H3
D
H3
H7
H
G
F
The holes
point in the same direction
H7

17
step 10: Attach the side frames
10.1. Using the pilot holes as a guide, attach side frames (B and C) to the previous assembly so that the mounting holes on the metal tabs overlap the threaded
inserts on the fixed shelf (D) properly.
The pilot holes
overlap the drilled holes
D
C
B
A

18
11.1. Fasten the side frames (B and C) to the fixed shelf (D) using four bolts (H4).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
(H4) x 4
1/4” x 13 mm bolt
step 11: fasten the side frames
(H11) x 1
hex wrench
B
C
D
H4
H4
H4
D
C
B
H4
A

19
12.1. Insert the wood dowels (H3) into the inner holes on the panels (A and D) as shown.
step 12: Insert the wood dowels
(H3) x 4
M6 x 30 mm
wood dowel
A
B
C
D
H3
H3

20
13.1. Fasten the side frames (B and C) in place using four bolts (H13) and four washers ( H14 and H15).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
step 13: fasten the side frames
(H11) x 1
hex wrench
(H13) x 4
1/4” x 27 mm bolt
(H14) x 4
lock washer
(H15) x 4
flat washer
A
B
C
FG
H13 H14 H15