Teknik Hudson Elm finish 5427422 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 566752 09/08/21
Purchased: __________________
1800x600 Desk
Hudson Elm finish | Model 5427422
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Part Identification
Hardware Identification
Optional Accessories
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
3
4
5
6
6-24
25-28
29-32
33-34
35
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C SMALL END (1)
D MODESTY PANEL (1)
E TOP (1)
A
B
C
D
E
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1S BLACK 9/16" LARGE HEAD SCREW - 20
41G PLATE - 2LEVELER - 6
46E WOOD DOWEL - 13 42F
TOUCH-UP PEN - 1
10M GROMMET - 2 2P GROMMET CAP- 2 3P86G SUPPORT BRACKET - 2
Page 4
CORD CLIP - 4
9P TWIST-LOCK®
FASTENER COVER - 17
125P HOLE PLUG - 8 127P

Page 5
Optional Accessories (sold separately)
å This piece of furniture accommodates one or more of the following optional accessories (sold
separately). å Powered Grommet (Item 5427829)
å Articulating Keyboard Shelf (Item 5426468)
The Articulating Keyboard Shelf is designed to be fastened to the underside of your desk, desk return, or credenza top.
å LED Light (Item 5426494)
The LED Light is designed to be fastened to the underside of a hutch.

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert four WOOD DOWELS (42F) into the exact holes
shown in the MODESTY PANEL (D).
å NOTE: You may need to gently tap the WOOD DOWELS
in with your hammer.
42F
42F
D
1. Insert the dowel end of the FASTENER
into the hole of the adjoining part.
NOTE: The dowel end of the FASTENER
must remain fully inserted in the hole of the
adjoining part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Hardware Usage Guide
Page 6

Step 2
Page 7
å If you purchased the 427413 to fasten to this desk 427422, then follow Steps 3-7. Next, go to the 427413 assembly and attachment.
å If you purchased the 427468 or the 427427 to fasten to this desk 427422 on the left, then follow Steps 8-13.
å If you purchased the 427468 or the 427427 to fasten to this desk 427422 on the right, then follow Steps 14-19.
427422
427468
427422
427468
427422
427427
427422
427427
427422
427413
427422
427413
CONNECTING 427413 - FOLLOW STEPS 3-7
CONNECTING 427422 ON LEFT - FOLLOW STEPS 14-19
CONNECTING 427422 ON RIGHT - FOLLOW STEPS 8-13

Step 3
å Fasten the ENDS (A and B) to the MODESTY PANEL (D).
Tighten six TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL
insert into the ENDS.
å NOTE: You will not use the SMALL END (C) in Steps 3-7. Extra
hardware has been provided for the SMALL END if needed.
Surface with
TWIST-LOCK®
FASTENERS
D
A
B
Page 8
Remember:
Righty tighty.
Lefty loosey.
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
Long edge with
TWIST-LOCK®
FASTENERS

Page 9
Step 4
å Insert seven WOOD DOWELS (42F) into the exact holes
shown in the TOP (E).
å NOTE: You may need to gently tap the WOOD DOWELS in
with your hammer.
å With the help of another person, fasten the ENDS (A and B)
and MODESTY PANEL (D) to the TOP (E). Tighten nine
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the TOP insert into the
ENDS and MODESTY PANEL.
D
A
E
B
Caution
Two person
lift required
42F

Step 5
å Fasten the SUPPORT BRACKETS (86G) to the MODESTY
PANEL (D) and TOP (E). Use twelve BLACK 9/16" LARGE
HEAD SCREWS (1S).
å Push four CORD CLIPS (9P) into the TOP (E).
9P
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
1S
D
E
86G
86G
Page 10