Teknik 5426135 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Home Study 3 Shelf Bookcase
Model 5426135
The stories of your life.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4-5
6-32
Page 2

A END (2)
B TOP (1)
C TOP FRONT MOLDING (1)
D TOP SIDE MOLDING (2)
E UPPER LEG (4)
F RIGHT FRONT/LEFT REAR LEG (2)
G LEFT FRONT/RIGHT REAR LEG (2)
H BOTTOM (1)
J UPPER END MOLDING (2)
K LOWER END MOLDING (2)
L VERTICAL END MOLDING (2)
M UPPER FIXED SHELF (2)
N ADJUSTABLE SHELF (1)
O BOTTOM MOLDING (1)
P UPPER BACK (2)
Q LOWER FIXED SHELF (1)
R DOOR (2)
S LOWER BACK (1)
A
A
B
C
D
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
R
M
K
J
L
E
EE
P
G
F
S
Page 3
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.

Hardware Identification
FURNITURE TIPPING
RESTRAINT KIT - 1
97
APPLIQUE CARD - 5
100P
WASHER - 2
10I
METAL PIN - 4
1R
CAM SCREW - 12
8F
PULL - 2
22K
DOOR STOP - 2
4I
WOOD DOWEL - 6
15F
NAIL - 30
1N
HIDDEN CAM - 36
1F CAM DOWEL - 24 2F
RUBBER SLEEVE - 4
2R
14H HINGE - 4
Page 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BROWN 1-1/2" FLAT HEAD SCREW - 7
14S
SILVER 1/4" MACHINE SCREW - 2
61S
BLACK 1/2" FLAT HEAD SCREW - 8
11S
BLACK 9/16" FLAT HEAD SCREW - 12
32S
BLACK 1-15/16" FLAT HEAD SCREW - 12
113S
Page 5

Hardware Usage Guide
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3. Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
HOW TO USE A HIDDEN CAM & CAM DOWEL
Hole
Hidden Cam
Cam Dowel
2.
Hole
Hidden Cam
Cam Dowel
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Metal end
Arrow
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
426135 www.sauder.com/servicePage 6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push five HIDDEN CAMS (1F) into the UPPER BACKS (P)
and a UPPER LEG (E). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
(5 used)
Metal end
P
P
E
Page 7

å Open the FURNITURE TIPPING RESTRAINT KIT (97)
and fasten the SAFETY STRAP to the TOP (B). Use the
provided BLACK 9/16" LARGE HEAD SCREW.
å NOTE: Position the SAFETY STRAP exactly as shown.
å Fasten the TOP (B) to the UPPER BACKS (P) and LEG (E).
Tighten the HIDDEN CAM in the LEG (E).
å NOTE: The HIDDEN CAMS in the UPPER BACKS will be
tightened in a later step.
Step 2
P
P
E
B
B
BLACK 9/16" LARGE HEAD SCREW
(1 used for the SAFETY STRAP)
Safety strap
97
Surface without
HIDDEN CAMS Surface without
HIDDEN CAMS
Surface with HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Page 8

å Push four HIDDEN CAMS (1F) into a UPPER FIXED SHELF (M).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Step 3
M
Do not tighten the HIDDEN CAMS in this step.
1F
2F
Metal end
Arrow
1F
2F
Arrow
(4 used)
Metal end
Page 9

å Fasten a UPPER FIXED SHELF (M) to the LEG (E). Tighten
one HIDDEN CAM.
Step 4
M
Surface without
HIDDEN CAMS
E
Page 10
Just think. The sooner
you do this, the sooner
you do something else.