Teknik Elstree 5426909 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Storage Cabinet
Elstree | Model 5426909
It stands. You sleep.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-21
22-25
26-29
30
31
Page 2
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C BOTTOM (1)
D ADJUSTABLE SHELF (1)
E LARGE BASE (2)
F SMALL BASE (2)
G BACK (1)
H LEFT DOOR (1)
J RIGHT DOOR (1)
K TOP (1)
A
BC
D
E
EF
F
G
H
J
K
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
METAL BRACKET - 6
4G
BLACK 9/16" LARGE HEAD SCREW - 40
1S BLACK 1/2" FLAT HEAD SCREW - 8
11S
DOOR STOP - 2
4I
WOOD DOWEL -4
15F
HIDDEN CAM - 4
1F CAM DOWEL - 4 2F
RUBBER SLEEVE - 4
2R
14H HINGE - 4
36F TWIST-LOCK®FASTENER - 4
31G CORNER BRACKET - 4
PULL - 2
189K
BACK CONNECTOR - 8
39F
Page 4
METAL PIN - 4
1R

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push four TWIST-LOCK FASTENERS (36F) into the large
holes in the ENDS (A and B).
å Insert four WOOD DOWELS (15F) into the ENDS (A and B)
using the exact holes shown.
A
B
36F
36F
15F
Page 6

Step 2
Page 7
å Push four HIDDEN CAMS (1F) into the BOTTOM (C).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
C
Do not tighten the HIDDEN CAMS in this step.
1F
2F
Arrow
Metal end
1F
2F
Metal end
Arrow

Step 3
B
Page 8
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
C
å Fasten the BOTTOM (C) to the LEFT END (B). Tighten two
HIDDEN CAMS.
Surface with
TWIST-LOCK®
FASTENERS
Surface with
HIDDEN CAMS

B
Page 9
C
A
å Fasten the RIGHT END (A) to the BOTTOM (C). Tighten two
HIDDEN CAMS.
Surface without
TWIST-LOCK®
FASTENERS
Surface with
HIDDEN CAMS
Step 4

Step 5
Page 10
å Carefully stand unit upright.
å Slide the BACK (G) into the grooves in the ENDS (A and B)
and the BOTTOM (C).
If fastening a Hutch to
this unit, the unit MUST
be placed against a wall.
A
C
G
B
Finished surface - if
placing unit against
a wall
Unfinished surface -
if placing unit out in
a room