Teknik 5427415 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
English pg 1-12
Français pg 13-14
Español pg 15-16
09/17/21 Lot # 572554
Purchased:
__________________
1500x600 Desk
Hudson Elm finish | Model 5427415
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
6
5-12
13-14
15-16
17-18
19
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C SMALL END (1)
D MODESTY PANEL (1)
E TOP (1)
A
BC
D
E
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
10M TOUCH-UP PEN - 1
2P GROMMET - 2 3P GROMMET
CAP - 2 9P CORD CLIP - 2
42F WOOD DOWEL - 13
TWIST-LOCK®
FASTENER COVER - 15
125P LARGE HOLE
PLUG - 8
127P
126P SMALL HOLE
PLUG - 2
46E LEVELER - 6
Page 4

Optional Accessories (sold separately)
å This piece of furniture accommodates one or more of the following optional accessories (sold
separately). å Powered Grommet (Item 5427829)
å Articulating Keyboard Shelf (Item 5426468)
The Articulating Keyboard Shelf is designed to be fastened to the underside of your desk, desk return, or credenza top.
Page 5

Step 1
D
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert four WOOD DOWELS (42F) into the
MODESTY PANEL (D).
å NOTE: You may need to gently tap the WOOD
DOWELS in with your hammer.
42F
42F
Page 6
Just think. The sooner
you do this, the sooner
you do something else.

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Step 2
å Using your hammer, gently tap four LEVELERS (46E)
completely into the holes in the ENDS (A and B).
å NOTE: Adjustments to the LEVELERS will be made later in
assembly once your unit is standing upright.
å Insert four WOOD DOWELS (42F) into
the ENDS (A and B).
å NOTE: You may need to gently tap the WOOD
DOWELS in with your hammer.
å NOTE: The SMALL END (C) is not used in
this assembly.
A
B
46E
(4 used)
(4 used)
42F
Page 7
Edge with TWIST-LOCK® FASTENERS

Step 3
å Fasten the ENDS (A and B) to the MODESTY PANEL (D).
Tighten six TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the MODESTY
PANEL insert into the ENDS.
B
A
D
Edge with TWIST-LOCK® FASTENERS
Surface with TWIST-LOCK® FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
Page 8
For support, place packing
foam or books here.

Step 4
å Push two CORD CLIPS (9P) into the holes shown in the TOP (E).
å NOTE: The CORD CLIPS are used to hold cords against the TOP.
9P
E
Pilot hole to be used
only if you purchased
the optional
426468 Articulating
Keyboard Shelf.
Page 9

å Insert three WOOD DOWELS (42F) into the
MODESTY PANEL (D).
å NOTE: You may need to gently tap the WOOD DOWELS
in with your hammer.
å Fasten the TOP (E) to the ENDS (A and B) and MODESTY
PANEL (D). Tighten seven TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the ENDS and
MODESTY PANEL insert into the TOP.
Step 5
E
A
B
D
42F
(3 used)
Page 10
Pro Tip: Lift with your
legs. And, you know,
your arms.