Teknik 5426484 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Executive Desk
Elstree | Model 5426484
Sit and surf.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
2-3
4-5
6-40
41-46
47-52
53-54
55
Page 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
B56 PENCIL DRAWER BOTTOM (2)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
D77 DRAWER BACK (2)
D78 FILE DRAWER BACK (2)
D133 RIGHT DRAWER SIDE (2)
D139 LEFT DRAWER SIDE (2)
D429 FILE LEFT DRAWER SIDE (2)
D430 FILE RIGHT DRAWER SIDE (2)
D565 PENCIL RIGHT DRAWER SIDE (2)
D566 PENCIL LEFT DRAWER SIDE (2)
D567 PENCIL DRAWER BACK (2)
D568 PENCIL DRAWER BOX FRONT (2)
D708 DRAWER BOTTOM (4)
E BOTTOM (2)
G LONG BASE (4)
H SHORT BASE (4)
J FILE DRAWER FRONT (1)
K DRAWER FRONT (2)
L MODESTY PANEL (1)
M FRONT MOLDING (1)
N PENCIL DRAWER FRONT (2)
O LOUVERED BACK (2)
P TOP (1)
W LOCKING DRAWER FRONT (1)
Adjustable Wrench
Tape Measure

Part Identification Now you know
our ABCs.
Page 3
B56
D77
D565
D566
D567
D568
D133
D708
D139
D78 D430
D708
D429
D78 D430
D708
D429
A
B
C
D
E
H
G
W
J
K
L
M
N
O
P
H
G
E
O
H
G
H
G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FILE ROD - 4
8B
FILE GLIDE - 4
6B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION
SLIDE - 4
40MC
EXTENSION
RAIL - 4
40MA 10A SLIDE
CAM - 8
HIDDEN
CAM - 8
1F CAM
DOWEL - 8
2F 36F TWIST-LOCK®
FASTENER - 18 METAL
BRACKET - 8
4G
31G CORNER
BRACKET - 8 76G L - LOCK BRACKET - 1 77G Z - LOCK BRACKET - 1
ANGLE
BRACKET - 6
27G
40CA CABINET RIGHT - 4 40CB CABINET LEFT - 4 40CC DRAWER RIGHT - 4 40CD DRAWER LEFT - 4
Page 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
LOCK PACK - 1
21J PULL - 6 189K GROMMET CAP - 2
1P
BLACK 9/16" LARGE HEAD SCREW - 92
1S 3S GOLD 5/16" FLAT HEAD SCREW - 48
BLACK 7/8" LARGE HEAD SCREW - 4
17S 30S BLACK 1-9/16" FLAT HEAD SCREW - 24
146S BLACK 2-3/8" FLAT HEAD SCREW - 4
Page 5
GROMMET - 2
10P
CORD CLIP - 2
4P HIDDEN WIRELESS Qi COMPATIBLE
CHARGER by EGGTRONIC - Item 425905
(sold separately)
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Page 6
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.

36F
L
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push two SAUDER TWIST-LOCK® FASTENERS (36F) into
the large holes in the MODESTY PANEL (L).
å Fasten the MODESTY PANEL (L) to the TOP (P). Tighten
two TWIST-LOCK® FASTENERS.
å Push two CORD CLIPS (4P) into the holes in the TOP (P).
å NOTE: The CORD CLIPS are used to hold the optional
HIDDEN WIRELESS CHARGER cord.
Step 1
L
Surface with TWIST-LOCK® FASTENERS
P
Meet Part (P). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
Executive Desk that’s easier to assemble
and friendlier to the environment.
Page 7
4P

å Push four SAUDER TWIST-LOCK® FASTENERS (36F) into
the large holes in the UPRIGHTS (C and D).
Step 2
D
C
Do not tighten the TWIST-LOCK® FASTENERS in this step.
36F
These holes
must be here.
Page 8

Step 3
Open end
å Separate the EXTENSION SLIDES (40MC) from the EXTENSION RAILS (40MA) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (40MA) to the UPRIGHTS (C and D). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged
diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other
hole that lines up with the hole in the UPRIGHT. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the FILE DRAWERS.
Push the black lever in and pull the SLIDE from the RAIL.
40MA40MC
Open end
3
2
1
1
2
3
4
4
D
C
GOLD 5/16" FLAT HEAD SCREW
(4 used for the RAILS)
3S
Page 9

å Fasten two CABINET RIGHTS (40CA) to the LEFT
UPRIGHT (D) and two CABINET LEFTS (40CB) to the
RIGHT UPRIGHT (C). Use eight GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #4.
å Fasten the L-LOCK BRACKET (76G) to the LEFT
UPRIGHT (D) exactly as shown. Use two BLACK 9/16"
LARGE HEAD SCREWS (1S).
Step 4
1
2
3
4
1
2
34
Roller end
GOLD 5/16" FLAT HEAD SCREW
(8 used for the RAILS)
3S
BLACK 9/16" LARGE HEAD SCREW
(2 used for the BRACKET)
1S
D
C
Roller end
76G
Page 10