Teknik 5424259 User manual

You could totally write
a novel on this.
Trestle Desk
Model 5424259
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4
5-23
24-26
27-29
30
31
Page 2
Short Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Q TOP (1)
R END (2)
S LEFT FRONT (1)
T RIGHT FRONT (1)
U BACK (1)
V LEFT UPRIGHT (1)
W RIGHT UPRIGHT (1)
X STRETCHER (2)
Y LEFT FRONT/RIGHT REAR LEG (2)
Z RIGHT FRONT/LEFT REAR LEG (2)
AA DRAWER FRONT (1)
BB DRAWER BOX FRONT (1)
CC LEFT DRAWER SIDE (1)
DD RIGHT DRAWER SIDE (1)
EE DRAWER BOTTOM (1)
FF DRAWER BACK (1)
Q
R
R
S
T
U
V
W
X
X
Y
Y
Z
Z
AA
BB
CC
DD
EE
FF
Page 3

Hardware Identification
DRAWER RIGHT - 1
19
HIDDEN CAM - 8
21 CAM DOWEL - 8 22 WOOD DOWEL - 8 23
PULL - 1
24 APPLIQUE CARD - 1
25
DRAWER LEFT - 1
20
CABINET RIGHT - 1
17 CABINET LEFT - 1 18
Page 4
SILVER 1-1/2" PAN HEAD SCREW - 2
28
GOLD 1-1/2" FLAT HEAD SCREW - 20
26
SILVER 1" PAN HEAD SCREW - 10
29
GOLD 1/2" FLAT HEAD SCREW - 12
27

Step 1
Page 5
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Using a hammer tap eight CAM DOWELS (22) into
the TOP (Q).
Q
22 (8 used)

å Insert eight WOOD DOWELS (23) to the LEGS (Y and Z).
Step 2
Y
Y
Z
Z
23
(8 used)
Page 6

å Push eight HIDDEN CAMS (21) into the ENDS (R)
and UPRIGHTS (V and W).
Step 3
R
R
V
W
Unfinished surface
Unfinished surface Finished surface
Finished surface
21
Arrow
(8 used)
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Page 7
Just think. The sooner
you do this, the sooner
you do something else.

å Fasten the UPRIGHTS (V and W) to the BACK (U). Use
two GOLD 1-1/2" FLAT HEAD SCREWS (26).
Step 4
U
W
V
Surface with HIDDEN CAMS
Unfinished surface
Finished edge
Finished edge
Unfinished surface
Finished edge
GOLD 1- 1/2" FLAT HEAD SCREW
(2 used in this step)
26
Page 8

å Fasten the FRONTS (S and T) to the UPRIGHTS (V and W).
Use two GOLD 1-1/2" FLAT HEAD SCREWS (26).
Step 5
S
T
V
W
Finished edge
Finished edge
Finished surface
Finished surface
GOLD 1- 1/2" FLAT HEAD SCREW
(2 used in this step)
26
Page 9

å Fasten the ENDS (R) to the FRONTS (S and T) and BACK (U).
Use four GOLD 1-1/2" FLAT HEAD SCREWS (26).
Step 6
US
T
R
R
Finished edge
Unfinished surface
Finished edge
Surface without
HIDDEN CAMS
GOLD 1- 1/2" FLAT HEAD SCREW
(4 used in this step)
26
26
Page 10